Chip tantalum capacitors
(Bottom surface electrode type : Large capacitance)
TCT series AL case
Datasheet
●Features
1) Bottom electrode configuration results in significantly greater compactness.
2) Filet formation enables easy visibility after mounting.
3) Ideal for noise removal on power supply lines with limited space.
4) Eco-friendly halogen-free products.
●Dimensions
(Unit: mm)
Dimensions
Size
L
3.2±0.2
W1
1.6±0.2
W2
1.2±0.2
H
1.1±0.1
S
0.8±0.2
●Part No. Explanation
T
C
T
①
A
L
②
① Series name
TCT
② Case style
AL：3216-3216(12)size
③ Rated voltage
CODE
Rated voltage(V)
0E
2.5
0G
4
0J
6.3
1A
10
1C
16
1D
20
1E
25
1V
35
1H
50
1
A
4
③
7
6
④
M
⑤
8
R －
⑥
⑦
④ Nominal capacitance
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure representing
the number of 0's.
⑤ Capacitance tolerance
M：±20%
⑥ Taping
8: Tape width
R: Positive electrode on the side opposite to sprocket hole
⑦ Discrimination code
*Contact us
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
1/7
2021.4.9 - Rev.003
TCT series AL case
Datasheet
●Rated table
Impedance(Ω)
Capacitance
(μF)
1.0
(105)
2.2
(225)
3.3
(335)
4.7
(475)
6.8
(685)
10
(106)
15
(156)
22
(226)
33
(336)
47
(476)
68
(686)
100
(107)
150
(157)
220
(227)
2.5
4
Rated voltage (V.DC)
10
16
20
6.3
25
35
50
8
8
8
4
4
4
4
2.5
3
2.7
☆2.5
☆2.5
☆Contact us
●Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity: The polarity should be shown by bar. (on the anode side)
(2) Rated DC voltage: A voltage code is shown as below table.
(3) Capacitance: A capacitance code is shown as below table.
Voltage Code
e
g
j
A
C
D
E
V
H
Rated DC
Voltage (V)
2.5
4
6.3
10
16
20
25
35
50
Capacitance
Code
E
N
S
A
E
J
N
S
W
a
Nominal
Capacitance (μF)
0.15
0.33
0.47
1.0
1.5
2.2
3.3
4.7
6.8
10
Capacitance
Code
e
j
n
s
w
a
e
j
n
s
Nominal
Capacitance (μF)
15
22
33
47
68
100
150
220
330
470
Visual typical example
voltage code and capacitance code are variable with parts number.
[TCT series AL case]
EX.)
A
(1)
s
(2)
As
(1) voltage code
*Contact us (2) capacitance code
Manufacture code
Anode band
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
2/7
2021.4.9 - Rev.003
TCT series AL case
Datasheet
●Characteristics
Item
Test conditions
(based on JIS C 5101-1 and JIS C 5101-3)
Voltage reduction when temperature exceeds
+85°C
Performance
Operating Temperature
-55℃~+125℃
Maximum operating
temperature with no
voltage derating
Rated voltage (V.DC)
Category voltage (V.DC)
Surge voltage (V.DC)
DC Leakage current
+85℃
Refer to " Standard list ".
Refer to " Standard list ".
Refer to " Standard list ".
Shall be satisfied the value on
" Standard list ".
Capacitance tolerance
Shall be satisfied allowance range.
±20%
Tangent of loss angle
(Df,tanδ)
Shall be satisfied the value on
" Standard list ".
Impedance
Shall be satisfied the value on
" Standard list ".
Resistance to
Soldering
heat
Temperature
cycle
Appearance
There should be no significant
abnormality.
L.C.
The indications should be clear.
Less than 200% of initial limit.
⊿C/C
Within +20/-30% of initial value.
DF
(tanδ)
Appearance
Less than 200% of initial limit.
L.C.
There should be no significant
abnormality.
The indications should be clear.
Less than 200% of initial limit.
⊿C/C
Within ±30% of initial value.
DF
(tanδ)
Less than 200% of initial limit.
*Contact us
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
3/7
at 85℃
at 125℃
at 85℃
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
Voltage : Rated voltage for 5min
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
Measuring frequency
:120 ± 12Hz
Measuring voltage
:0.5Vrms + 1.5V.DC
:DC Equivalent series circuit
Measuring circuit
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
Measuring frequency
:120 ± 12Hz
Measuring voltage
:0.5Vrms + 1.5V.DC
Measuring circuit
:DC Equivalent series circuit
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
Measuring frequency
:100 ± 10kHz
Measuring voltage
:0.5Vrms or less
Measuring circuit
:DC Equivalent series circuit
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Solder temp
:240 ± 5°C
Duration
:10 ± 0.5s
Repetition
:1
After the specimens, leave it at room temperature
for over 24h and then measure the sample.
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Temp.
Time
1
30±3min
-55±3℃
2
Room Temp.
3min or less
3
30±3min
125±2℃
4
Room Temp.
3min or less
After the specimens, leave it at room temperature
for over 24h and then measure the sample.
2021.4.9 - Rev.003
TCT series AL case
Item
Moisture
resistance
Performance
Appearance
L.C.
⊿C/C
Temperature
Stability
Datasheet
There should be no significant
abnormality.
The indications should be clear.
Less than 200% of initial limit.
Within ±20% of initial value.
DF
Less than 300% of initial limit.
(tanδ)
Temp.：-55℃
⊿C/C
Within 0/-15% of initial value.
DF
(tanδ)
L.C.
Test conditions
(based on JIS C 5101-1 and JIS C 5101-3)
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60±2°C and 90 to 95% RH, respectively, for
500+12/0h leave it at room temperature for
over 24h and then measure the sample.
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
Shall be satisfied the value on
" Standard list "
－
Temp.：+85℃
⊿C/C
Within +15/0% of initial value.
DF
(tanδ)
L.C.
Shall be satisfied the value on
" Standard list "
Less than 1000% of initial limit.
Temp.：+125℃
⊿C/C
Within +20/0% of initial value.
Surge
voltage
DF
(tanδ)
L.C.
Shall be satisfied the value on
" Standard list "
Less than 1250% of initial limit.
Appearance
There should be no significant
L.C.
Loading at
High
temperature
abnormality.
The indications should be clear.
Less than 200% of initial limit.
⊿C/C
Within ±20% of initial value.
DF
(tanδ)
Appearance
Less than 200% of initial limit.
There should be no significant
abnormality.
L.C.
The indications should be clear.
Less than 200% of initial limit.
⊿C/C
Within +20/-30% of initial value.
DF
(tanδ)
Less than 300% of initial limit.
*Contact us
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
4/7
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage via the serial
resistance of 1kΩ ever 5±0.5 min. for 30±5 s.
each time in the atmospheric condition of
85±2°C. Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature
for over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 1000+72/0 h
without discontinuation via the serial resistance
of 3Ω or less at a temperature of 85±2°C, leave
the sample at room temperature / humidity for
over 24h and measure the value.
2021.4.9 - Rev.003
TCT series AL case
Item
Terminal
strength
Datasheet
Performance
Capacitance
Appearance
The measured value should be
stable.
There should be no significant
abnormality.
Test conditions
(based on JIS C 5101-1 and JIS C 5101-3)
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to
1mm and by a prescribed tool maintains the
condition for 5s.
(See the figure below)
20
50
F(Apply force)
R230
1.0mm
thickness=1.6mm
45
Adhesiveness
The terminal should not come off.
45
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 2N in the two directions shown in
the figure below for 10±1s after mounting the
terminal on a circuit board.
Products
Apply force
A circuit board
Dimensions
Refer to "External dimensions".
Resistance to
solvents
The indication should be clear.
Solderability
3/4 or more surface area of the
solder coated terminal dipped in
the soldering bath should be
covered with the new solder.
Vibration
*Contact us
Capacitance
Appearance
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
Measure value should not fluctuate
during the measurement.
There should be no significant
abnormality.
5/7
Measure using a caliper of JIS B 7507 Class
2 or higher grade.
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30±5s, at room
temperature.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm / s
Pre-treatment (accelerated aging):
Leave the sample on the boiling distilled water
for 1h.
Solder temp. : 245±5°C
Duration : 3±0.5s
Solder : M705
Flux : Rosin 25% IPA 75%
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print
circuit board.
2021.4.9 - Rev.003
TCT series AL case
Datasheet
●Standard products list
Rated
Category
Surge
voltage
voltage
voltage
85℃
105℃
85℃
Cap.
Tole-
Leakage
tanδ
rance
current
120Hz
120Hz
Impedance
100kHz
25℃
Part No.
1WV
-55℃
25℃
105℃
5min
(V)
(V)
(V)
(μF)
(%)
(μA)
(%)
(%)
(%)
(Ω)
4
2.5
5
220
±20
20.0
35
20
25
2.5
TCTAL0J107M8R
6.3
4
8
100
±20
6.3
34
18
24
3
TCTAL0J157M8R
6.3
4
8
150
±20
94.5
80
30
40
2.7
＊ TCTAL0J227M8R-V1
6.3
4
6.3
220
±20
280.0
80
30
40
2.5
TCTAL1A476M8R
10
6.3
13
47
±20
4.7
35
20
25
4
＊ TCTAL1A107M8R-V1
10
6.3
10
100
±20
50.0
80
30
40
2.5
TCTAL1C226M8R
16
10
20
22
±20
3.6
35
20
25
4
TCTAL1C336M8R
16
10
20
33
±20
5.3
35
20
25
4
TCTAL1D106M8R
20
13
26
10
±20
2.0
30
15
20
8
TCTAL1D226M8R-V1
20
13
20
22
±20
4.4
35
20
25
4
TCTAL1E475M8R
25
16
32
4.7
±20
1.2
30
15
20
8
TCTAL1V335M8R
35
22
44
3.3
±20
1.2
30
15
20
8
TCTAL0G227M8R-D
*Contact us
Please ask for latest specification to our sales.
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
6/7
2021.4.9 - Rev.003
TCT series AL case
Datasheet
●Packaging specifications
Sprocket hole φDo
t1
E
A
F
B
W
t2
Component is loaded.
P1
P2
Pull-out direction
PO
Unit[㎜]
A
B
W
E
F
P1
P2
1.90±0.10
3.50±0.10
8.00±0.20
1.75±0.10
3.50±0.05
4.00±0.10
2.00±0.05
PO
DO
t1
t2
Standard packaging quantity
4.00±0.10
φ1.55±0.05
0.25±0.05
1.30±0.05
3,000pcs
9.0+1.0/0
●Reel dimensions
φ180+0/-1.5
φ60+1.0/0
φ13±0.2
11.4±1.0
Unit[㎜]
ラベル貼付位置
引き出し方向
EIAJ ET-7200A
*Contact us
www.rohm.com
© 2021 ROHM Co.,Ltd.All rights reserved.
7/7
2021.4.9 - Rev.003
Notice
Precaution on using ROHM Products
1.
Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.004
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2.
ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.004
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001
