TCTOBL1E156M8R-ZB1

Conductive polymer chip capacitors (Bottom surface electrode type : Large capacitance) TCTO series BL case Datasheet ●Features 1) Conductive polymer used at the cathode for ultra-low ESR. 2) Bottom electrode configuration results in the largest capacitance. 3) Compact, low profile, high capacitance contribute to smaller, thinner sets with greater functionality. 4) Conductive polymer has a self-healing function that prevents failure, resulting in safe, high reliability operation. ●Dimensions (Unit: mm) Dimensions Size L 3.5±0.2 W1 2.8±0.2 W2 2.0±0.2 H 1.1±0.1 S 0.8±0.2 ●Part No. Explanation T C T O ① B L ② ① Series name TCTO ② Case style BL：3528(12)size ③ Rated voltage CODE Rated voltage(V) 0D 2 0E 2.5 0G 4 0J 6.3 1A 10 1C 16 1D 20 1E 25 1V 35 www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. 0 D 4 ③ 7 7 ④ M ⑤ 8 R － ⑥ ⑦ ④ Nominal capacitance Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. ⑤ Capacitance tolerance M：±20% ⑥ Taping 8: Tape width R: Positive electrode on the side opposite to sprocket hole ⑦ Discrimination code 1/7 2021.7.1 - Rev.003 Datasheet TCTO series BL case ●Rated table ESR(mΩ) Capacitance （μF） 4.7 (475) 6.8 (685) 10 (106) 15 (156) 22 (226) 33 (336) 47 (476) 68 (686) 2 2.5 Rated voltage (V.DC) 6.3 10 16 4 100 20 25 ☆100 ☆100 100 ☆100 35 150 ☆200 70 70 ☆25/ ☆35/45 100 (107) 150 220 (157) (227) ☆25/☆35 330 (337) 20/ ☆25/ ☆25/☆35 ☆35/☆45 470 (477) 25/35 ☆25/☆35 ☆15 ☆Under development ●Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity: The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage: A voltage code is shown as below table. (3) Capacitance: A capacitance code is shown as below table. Voltage Code d e g j k A C D E V Rated DC Voltage (V) 2 2.5 4 6.3 8 10 16 20 25 35 Capacitance Code E N S A E J N S W a Nominal Capacitance (μF) 0.15 0.33 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 Capacitance Code e j n s w a e j n s Nominal Capacitance (μF) 15 22 33 47 68 100 150 220 330 470 Visual typical example voltage code and capacitance code are variable with parts number. [TCTO series BL case] EX.) d (1) s (2) (1) voltage code (2) capacitance code www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. Manufacture code ds 2/7 Anode band 2021.7.1 - Rev.003 Datasheet TCTO series BL case ●Characteristics Item Test conditions (based on JIS C 5101-1 and JIS C 5101-3) Performance Operating Temperature -55℃~+105℃ Maximum operating temperature with no voltage derating Rated voltage (V.DC) +105℃ Refer to " Standard list ". at 105℃ Category voltage (V.DC) Refer to " Standard list ". at 105℃ Surge voltage (V.DC) Refer to " Standard list ". at 85℃ DC Leakage current Shall be satisfied the value on " Standard list ". Capacitance tolerance Shall be satisfied allowance range. ±20% Tangent of loss angle (Df,tanδ) Shall be satisfied the value on " Standard list ". ESR Shall be satisfied the value on " Standard list ". As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 5min As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120 ± 12Hz Measuring voltage : 0.5Vrms + 1.5V.DC Measuring circuit : DC Equivalent series circuit As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120 ± 12Hz Measuring voltage : 0.5Vrms + 1.5V.DC Measuring circuit : DC Equivalent series circuit As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100 ± 10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 240 ± 5°C Duration : 10 ± 0.5s Repetition : 1 After the specimens, leave it at room temperature for over 24h and then measure the sample. Resistance to Soldering heat Appearance L.C. Temperature cycle There should be no significant abnormality. The indications should be clear. Less than 150% of initial limit. ⊿C/C Within ±20% of initial value. DF (tanδ) Appearance Less than 150% of initial limit. L.C. There should be no significant abnormality. The indications should be clear. Less than 500% of initial limit. ⊿C/C Within ±20% of initial value. DF (tanδ) Less than 150% of initial limit. www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. 3/7 As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Temp. Time 1 30±3min -55±3℃ 2 Room Temp. 3min or less 3 30±3min 105±2℃ 4 Room Temp. 3min or less After the specimens, leave it at room temperature for over 24h and then measure the sample. 2021.7.1 - Rev.003 Datasheet TCTO series BL case Item Moisture resistance Temperature Stability Performance Appearance There should be no significant abnormality. L.C. The indications should be clear. Less than 150% of initial limit. ⊿C/C Within +30/-20% of initial value. DF Less than 150% of initial limit. (tanδ) Temp.：-55℃ ⊿C/C Within 0/-20% of initial value. DF (tanδ) L.C. Test conditions (based on JIS C 5101-1 and JIS C 5101-3) As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 60±2℃ and 90~95%(Relative Humidity) , respectively ,for 500+12/0h leave it at room temperature for over 24h and then measure the sample. As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 Shall be satisfied the value on " Standard list " － Temp.：+105℃ ⊿C/C Within +80/0% of initial value. Surge voltage DF (tanδ) L.C. Shall be satisfied the value on " Standard list " Less than 1000% of initial limit. Appearance There should be no significant L.C. Loading at High temperature abnormality. The indications should be clear. Less than 150% of initial limit. ⊿C/C Within ±20% of initial value. DF (tanδ) Appearance Less than 150% of initial limit. L.C. There should be no significant abnormality. The indications should be clear. Less than 200% of initial limit. ⊿C/C Within ±20% of initial value. DF (tanδ) Less than 150% of initial limit. www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. 4/7 As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 Apply the specified surge voltage via the serial resistance of 1kΩ ever 5±0.5 min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage or category voltage for 1000+72/0hwithout discontinuation via the serial resistance of 3Ωor less at a temperature of 105±2℃ , leave the sample at room temperature/ humidity for over 24h and measure the value. 2021.7.1 - Rev.003 Datasheet TCTO series BL case Item Terminal strength Performance Capacitance Appearance The measured value should be stable. There should be no significant abnormality. Test conditions (based on JIS C 5101-1 and JIS C 5101-3) As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintains the condition for 5s. (See the figure below) 20 50 F(Apply force) R230 1.0mm thickness=1.6mm 45 Adhesiveness The terminal should not come off. 45 As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 2N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. Products Apply force A circuit board Dimensions Refer to "External dimensions". Resistance to solvents The indication should be clear. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. Vibration Capacitance Appearance www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. Measure value should not fluctuate during the measurement. There should be no significant abnormality. 5/7 Measure using a caliper of JIS B 7507 Class 2 or higher grade. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed=25±2.5mm / s Pre-treatment (accelerated aging): Leave the sample on the boiling distilled water for 1h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25% IPA 75% As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. 2021.7.1 - Rev.003 Datasheet TCTO series BL case ●Standard products list Rated Category Surge Cap. voltage voltage voltage 105℃ 105℃ 85℃ Tole- Leakage tanδ rance current 120Hz 120Hz ESR allowable 100kHz 25℃ Part No. 1WV -55℃ 25℃ Max ripple current 105℃ ≦45℃ 5min 100kHz (V) (V) (V) (μF) (%) (μA) (%) (%) (%) (mΩ) (mArms) ＊ TCTOBL0D477M8R-ZE1 2 2 2.6 470 ±20 94.0 30 15 20 15 2,500 ＊ TCTOBL0E227M8R-ZK1 2.5 2.5 3.2 220 ±20 55.0 8 8 12 25 2,000 ＊ TCTOBL0E227M8R-ZN1 2.5 2.5 3.2 220 ±20 55.0 8 8 12 35 1,700 TCTOBL0E337M8R-2A1 2.5 2.5 3.2 330 ±20 82.5 30 15 20 20 2,200 ＊ TCTOBL0E337M8R-ZK1 2.5 2.5 3.2 330 ±20 82.5 30 15 20 25 2,000 ＊ TCTOBL0E337M8R-ZN1 2.5 2.5 3.2 330 ±20 82.5 30 15 20 35 1,700 ＊ TCTOBL0G337M8R-ZK1 4 4 5 330 ±20 132.0 30 15 20 25 2,000 ＊ TCTOBL0G337M8R-ZN1 4 4 5 330 ±20 132.0 30 15 20 35 1,700 ＊ TCTOBL0G337M8R-ZS1 4 4 5 330 ±20 132.0 30 15 20 45 1,500 ＊ TCTOBL0J107M8R-ZK1 6.3 6.3 8 100 ±20 63.0 8 8 12 25 2,000 ＊ TCTOBL0J107M8R-ZN1 6.3 6.3 8 100 ±20 63.0 8 8 12 35 1,700 TCTOBL0J107M8R-ZS1 6.3 6.3 8 100 ±20 63.0 8 8 12 45 1,500 TCTOBL0J157M8R-ZK1 6.3 6.3 8 150 ±20 94.5 30 15 20 25 2,000 TCTOBL0J157M8R-ZN1 6.3 6.3 8 150 ±20 94.5 30 15 20 35 1,700 ＊ TCTOBL0J227M8R-ZK1 6.3 6.3 8 220 ±20 139.0 30 15 20 25 2,000 ＊ TCTOBL0J227M8R-ZN1 6.3 6.3 8 220 ±20 139.0 30 15 20 35 1,700 TCTOBL1A476M8R-ZB1 10 10 13 47 ±20 47.0 8 8 12 100 1,000 TCTOBL1C336M8R-ZW1 16 16 20 33 ±20 52.8 10 10 15 70 1,200 TCTOBL1C476M8R-ZW1 16 16 20 47 ±20 75.2 10 10 15 70 1,200 ＊ TCTOBL1D226M8R-ZB1 20 20 23 22 ±20 88.0 10 10 15 100 1,000 ＊ TCTOBL1E106M8R-ZB1 25 25 29 10 ±20 50.0 10 10 15 100 1,000 TCTOBL1E156M8R-ZB1 25 25 29 15 ±20 75.0 10 10 20 100 1,000 ＊ TCTOBL1E226M8R-ZB1 25 20 29 22 ±20 110.0 10 10 20 100 1,000 TCTOBL1V685M8R-ZF1 35 35 40 6.8 ±20 47.6 10 10 15 150 800 ＊ TCTOBL1V106M8R-ZD1 35 35 40 10 ±20 70.0 10 10 15 200 700 ＊This specification has possibility of charge, due to underdevelopment product. Please ask for latest specification to our sales. www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. 6/7 2021.7.1 - Rev.003 Datasheet TCTO series BL case ●Packaging specifications Sprocket hole φDo t1 E A F B W t2 Component is loaded. P1 P2 Pull-out direction PO Unit[㎜] A B W E F P1 P2 3.20±0.10 3.80±0.10 8.00±0.20 1.75±0.10 3.50±0.05 4.00±0.10 2.00±0.05 PO DO t1 t2 Standard packaging quantity 4.00±0.10 φ1.55±0.05 0.25±0.05 1.4±0.10 3,000pcs 9.0+1.0/0 ●Reel dimensions φ180+0/-1.5 φ60+1.0/0 φ13±0.2 11.4±1.0 Unit[㎜] Label Pull-out direction EIAJ ET-7200A ●Damp proof package ①One reel is packed in aluminum bag. The size of aluminum bag is 240(a) x 250(b)mm. The size up to 230(c)mm is to zipper. ②A desiccant is packed with a reel. ③The aluminum bag is heat-sealed. ④The label of the same as the label on the reel is placed on the aluminum bag. b c a www.rohm.com © 2021 ROHM Co.,Ltd.All rights reserved. 7/7 2021.7.1 - Rev.003 Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications. 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensure the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2015 ROHM Co., Ltd. All rights reserved. R1107 A Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001