TRR03
Resistors
Sulfur Tolerant Chip Resistors
TRR03 (0603 size)
Features 1) Unique protect materials prevent from silver sulfide occurrence under sulfur enviromnet. 2) Highly recommended for automotive, industrial and Power supply applications under sulfur environment. 3) Realize the good cost performance not like the Au terminal components from other suppliers. 4) ROHM resistors have approved ISO9001 / ISO/TS 16949 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it.
Ratings
Item Rated power Conditions Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C.
100 80
POWER LOAD (%)
Specifications 0.10W (1 / 10W) at 70°C
60 40 20 0
−55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E= Nominal resistance Operating temperature P×R E: Rated voltage (V) P: Rated power (W) R: Nominal resistance (Ω) Limiting element voltage 50V
See Table 1. −55°C to +155°C
Jumper type Resistance Rated current Max. 50mΩ 1A
Table 1 Resistance tolerance J (±5%) F (±1%) Resistance range (Ω) 1.0 ≤ R ≤ 9.1 10 ≤ R ≤ 10M (E24) 10 ≤ R ≤ 10M (E24) (E24,96) Resistance temperature coefficient (ppm/°C) ±400 ±200 ±100
Operating temperature −55°C to +155°C
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
1/4
TRR03
Resistors
Characteristics
Item Guaranteed value Resistor type Jumper type J : ±5% F : ±1% Max. 50mΩ Test conditions (JIS C 5201-1) JIS C 5201-1 4.5
Resistance Variation of resistance with temperature Overload
See Table.1 ± (2.0%+0.1Ω) Max. 50mΩ
JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Maximum overload voltage : 100V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. JIS C 5201-1 4.19 Test temp. : −55°C to +125°C 5cyc JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h to 1,048h JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h JIS C 5201-1 4.25.3 155°C Test time : 1,000h to 1,048h JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol JIS C 5201-1 4.33
Solderability
A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. ± (1.0%+0.05Ω) ± (3.0%+0.1Ω) Max. 50mΩ Max. 100mΩ
Resistance to soldering heat Rapid change of temperature Damp heat, steady state
± (3.0%+0.1Ω) Endurance at 70°C ± (3.0%+0.1Ω) Endurance
Max. 100mΩ
Max. 100mΩ
± (1.0%+0.05Ω) Resistance to solvent
Max. 50mΩ
Bend strength of the end face plating
± (1.0%+0.05Ω) Max. 50mΩ Without mechanical damage such as breaks.
2/4
TRR03
Resistors
Dimensions (Unit : mm)
① 0.4 ± 0.1 ②
③
④
No.
1
Material Silver thick film electrode Resistive element Over coating Protection electrode Silver thick film electrode Nickel electrode Sn electrode Alumina substrate
⑤ 0.3 ± 0.2 1.6 ± 0.1 ⑧ ⑦
2 3
0.45 ± 0.1
4
⑥
5 6 7 8
Packaging
Reel Taping
P0 P2 P1 φD0 E F B0
08 06 04 02 02 04 06 08
0.8 ± 0.1
W
A
B
D
A0
Heat crimp cover Tape Thick paper mount (Underside paper tape) Chip resistor Square punchout hole
T2 C
Label EIAJ ET-7200B compliant
(Unit : mm)
W
8.0±0.3
F
3.5±0.05
E
1.75±0.1
A0
1.1±0.1
B0
1.9±0.1
(Unit : mm) A B C D
D0
φ1.5 +0.1 0
P0
4.0±0.1
P1
4.0±0.1
P2
2.0±0.05
T2
Max. 1.1
φ180
0 −3
φ60
+1 0
9
+1.0 0
φ13±0.2
3/4
TRR03
Resistors
Part No. Explanation
TRR03
Part No.
EZP
J
J
±5%
Resistance tolerance Nominal resistance
F ±1% J is also used for jumper Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance Resistance tolerance code F J : : 4 digits 3 digits
Packaging Specifications Code
Part No. TRR03 Code EZP Resistance tolerance FX(±1%) J(±5%) Packaging specifications Paper tape (4mm Pitch) Reel φ180mm (7inch) Basic ordering unit (pcs) 5,000
Reel (φ180) : JEITA ET-7200B : Standard product
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121 FAX : +81-75-315-0172
Appendix1-Rev2.0