TRR18EZPJ2R2

Sulfur Tolerant Chip Resistors TRR Series Features 1) Special construction prevents sulfur gas penetration, significantly increasing reliability. 2) Highly recommended for automotive, industrial and Power supply applications under sulfur environment. 3) ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 4) Corresponds to AEC-Q200. (TRR03 / 10 / 18) Products List Size Part No. (mm) (inch) Rated Power Limiting Element Voltage (70˚C) (W) (V) Maximum Overload Voltage (V) Temperature Resistance Coefficient Tolerance Resistance Range (ppm / °C) +500 / −250 TRR01 1005 0402 0.063 100 50 ±200 ±100 Operating Temperature Range (°C) Series (%) 1Ω to J(±5%) 9.1Ω E24 10Ω to 10MΩ 10Ω to 2.2MΩ F(±1%) Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 TRR03 1608 0603 0.1 100 50 ±200 ±100 1Ω to J(±5%) 9.1Ω E24 10Ω to 10MΩ 10Ω to 10MΩ F(±1%) Jumper type : Rmax = 50m Ω / Imax. = 1A ±400 TRR10 2012 0805 0.125 200 150 ±200 ±100 1Ω to J(±5%) −55 to +155 9.1Ω E24 10Ω to 10MΩ 10Ω to 2.2MΩ F(±1%) Jumper type : Rmax = 50m Ω / Imax. = 2A ±400 TRR18 3216 1206 0.25 400 200 ±200 ±100 1Ω to J(±5%) 9.1Ω E24 10Ω to 10MΩ 10Ω to 2.2MΩ F(±1%) Jumper type : Rmax = 50m Ω / Imax. = 2A ∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Part Number Description T R R 0 1 Part No. Size (mm [inch]) TRR 01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) (Sulfur Tolerant Chip Resistors) M Z P J Packaging Specifications Code Part No. Code Packaging specifications Quantity / Reel TRR01 MZP Paper tape (2mm Pitch) 10,000 TRR03 EZP Paper tape (4mm Pitch) 5,000 TRR10 EZP Paper tape (4mm Pitch) 5,000 TRR18 EZP Paper tape (4mm Pitch) 5,000 Resistance Tolerance D ( ±0.5% ) F ( ±1% ) J ( ±5% ) 1 0 5 Nominal Resistance Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance F J Resistance code : : 4 digits 3 digits Ex.) 1Ω = 1R0 9.1Ω = 9R1 10 Ω = 10R0 100 1M Ω = 1004 105 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 1/4 ( ±5% ) ( ±5% ) ( ±1%) ( ±5% ) ( ±1%) ( ±5% ) 2012.06 - Rev.A TRR Series Data Sheet Chip Resistor Dimensions and Markings   TRR01 / 03 TRR10 / 18 L L W W a a t t b b (Unit : mm) Marking existence ∗Including jumper type Part No. (mm) (inch) L W t a b TRR01 1005 0402 1.0±0.05 0.5±0.05 0.35±0.05 0.33±0.08 0.25 −0.1 No TRR03 1608 0603 1.6±0.1 0.8±0.1 0.45±0.1 0.4±0.1 0.3±0.2 No TRR10 2012 0805 2.0±0.1 1.25±0.1 0.55±0.1 0.43 −0.1 0.4±0.2 No TRR18 3216 1206 3.2±0.15 1.6±0.15 0.55±0.1 0.69 −0.15 0.5±0.25 No +0.15 +0.2 +0.05 Land pattern Example B D C Land A (Unit : mm) Dimensions A B C D TRR01 0.5 1.3 0.5 0.4 TRR03 1.0 2.0 0.8 0.5 TRR10 1.2 2.6 1.15 0.7 TRR18 2.2 4.0 1.5 0.9 Part No. www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 2/4 2012.06 - Rev.A TRR Series Data Sheet Derating Curve When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.  TRR01 / 03 / 10 / 18 PERCENT RATED POWER (%) 100 80 60 40 20 0 −55 0 70 100 AMBIENT TEMPERATURE (°C) 155 Characteristics Guaranteed Value Resistor Type Jumper Type Test Items Test Conditions Resistance See P.1 20°C Variation of resistance with temperature See P.1 Measurement : +20 / −55 / +20 / +125°C ± (2.0%+0.1Ω) Overload Max. 50mΩ A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability ± (1.0%+0.05Ω) Resistance to soldering heat Max. 50mΩ No remarkable abnormality on the appearance. Rated voltage (current) ×2.5, 2s Maximum overload voltage Rosin·Ethanol : 25% (Weight) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s Soldering condition : 260±5°C Duration of immersion : 10±1s Rapid change of temperature ± (1.0%+0.05Ω) Max. 50mΩ Test temp. : −55°C to +125°C 5cycle Damp heat, steady state ± (3.0%+0.1Ω) Max. 100mΩ 40°C, 93%RH (Relative Humidity) Test time : 1,000h to 1,048h Endurance at 70°C ± (3.0%+0.1Ω) Max. 100mΩ 70°C Rated voltage (current) 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h Endurance ± (3.0%+0.1Ω) Max. 100mΩ 155°C Test time : 1,000h to 1,048h Resistance to solvent ± (1.0%+0.05Ω) Max. 50mΩ 23±5°C, Immersion cleaning, 5±0.5min Solvent : 2−propanol ± (1.0%+0.05Ω) Max. 50mΩ Bend strength of the end face plating Without mechanical damage such as breaks. − Compliance Standard(s) : IEC60115−8 JISC 5201−8 Technical data Parameter Unit TRR01 TRR03 TRR10 TRR18 Insulation resistance MΩ 1000 1000 1000 1000 Failure rate Fit 0.2188 1.4841 0.5153 3.1033 mg/pc 0.70 2.12 5.05 9.51 Weight www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 3/4 2012.06 - Rev.A TRR Series Data Sheet Tape Dimensions  (Unit : mm) Paper Tape Part No. W F E A0 B0 TRR01 8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1 TRR03 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 TRR10 8.0±0.3 3.5±0.05 1.75±0.1 1.65 TRR18 8.0±0.3 3.5±0.05 1.75±0.1 1.95 Part No. D0 P0 P1 P2 T2 P0 P2 P1 φD0 E F W B0 A0 Top tape Base paper (Bottom tape) Components Cavity T2 +0.2 −0.1 +0.1 −0.05 2.4 3.5 +0.2 −0.1 +0.15 −0.05 TRR01 φ1.5 +0.1 0 4.0±0.1 2.0±0.05 2.0±0.05 Max 1.1 TRR03 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 TRR10 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 TRR18 φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 02 04 06 08 06 D 04 B 02 A 08 Reel Dimensions C Label ACCORDING TO EIAJ ET-7200B (Unit : mm) Part No. A B C D TRR01 TRR03 φ180 TRR10 0 −1.5 φ60 +1.0 0 9 +1.0 0 φ13±0.2 TRR18 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 4/4 2012.06 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. R1120A