SSO-AD-230-TO52
Avalanche Photodiode
Special characteristics:
High gain at low bias voltage Fast rise time 230 µm diameter active area low capacitance
Parameters:
active area Dark current (M=100) 1) Total capacitance (M=100) Break down voltage UBR (at ID=2µA) Temperature coefficient of UBR Spectral responsivity (at 780 nm) Cut-off frequency (-3dB) Rise time Optimum gain Gain M "Excess Noise" factor (M=100) "Excess Noise" index (M=100) Noise current (M=100) N.E.P. (M=100, 880 nm) Operating temperature Storage temperature 50 - 60 min 200
1)
Package 1 (TO52) :
0,042 mm ∅ 230 µm max. 1,5 nA typ. 0,6 nA typ. 1,5 pF (90 ... 240) typ. 120 - 190 V typ. 0,4 %/°C min. 0,40 A/W typ. 0,45 A/W typ. 2 GHz typ. 180 ps
2
typ. 2,2 typ. 0,2 typ. 0,5 pA/Hz
½
typ. 1 * 10 W/Hz -20 ... +70°C -60 ... +100°C
-14
½
1) measurement conditions: Setup of photo current 10nA at M=1 and irradiation by a NIR-LED (880 nm, 80 nm bandwith). Rise of the photo current up to 1 µA, (M=100) by internal multiplication due to an increasing bias voltage.
SSO - AD - serie Spectral Responsivity at M=1
0,600 0,500 0,400 0,300 0,200 0,100 0,000 400 500 600 700 800 900 1000 1100 60 50 40 30 20 10 0 400 500
SSO - AD - serie Spectral Responsivity at M=100
Sabs (A/W)
Sabs (A/W)
600
700
800
900
1000
1100
Wavelength (nm)
Wavelength (nm)
SSO - AD - serie quantum efficiency for M=1
1,00 0,90 0,80 0,70 0,50 0,40 0,30 0,20 0,10 0,00 400 480 560 640 720 800 880 960 1040
4 2 0 0 20 Ctot (pF) 14 12 10 8 6
SSO-AD 230 Ctot=f(UR) at f=100kHz
16
0,60 QE
40 UR (V)
60
80
100
wavelength (nm)
SSO-AD 230 dark current = f(UR)
1000 100 10 M 1 0,1 0,01 0 20 40 60 80 UR (V) 100 120 140 160 10,00 100,00 10000,00
SSO-AD 230 gain = f(UR/UBR) at λ = 880 nm
1000,00
ID (pA)
1,00 0,0 0,2 0,4 UR/UBR 0,6 0,8 1,0
Maximum Ratings:
• • • • max. electrical power dissipation max. optical peak value, once max. continous optical operation ( Pelectr. = Popt. * Sabs * M * UR )
Current limiting resistor
100 mW at 22°C 200 mW for 1 s IPh (DC) ≤ 250 µA ≤ 1 mA for signal 50 µs "on" / 1 ms "out"
Bias supply voltage
Application hints:
• • • • • • • Current limit is to be realized via protecting resistor or current limiting - IC inside the supply voltage. Use of low noise read-out - IC. For higher gain a regulation of bias voltage due to the temperature is to be realized. For very small signals stray light (noise source) is to be excluded by filters in order to improve the signal-noise relation. Avoid touching the window with fingers! Careful cleaning with Ethyl alcohol possible. Avoid use of pointed and scratching tools!
min. 0,1 µF, closest to APD APD
Diode, protective circuit
Handling precautions:
• • • Soldering temperature min. Pin - length ESD - protection Storage
Read-out circuit or f.e. 50Ω Load resistance
•
260°C for max. 10 s. The device must be protected against solder flux vapour! 2mm Only small danger for the device. Standard precautionary measures are sufficient. Store devices in conductive foam.
2000/05