CX-1V-03

CX-1V-03 CRYSTAL 10 kHz to 600 kHz ™ Miniature Quartz Crystal for Pierce Oscillators DESCRIPTION The CX-1V quartz crystal is a high quality tuning fork resonator for use in Pierce (single inverter) oscillators. The CX-1V is hermetically sealed in a rugged, miniature ceramic package, one-fourth the size of an eight-pin mini-DIP. The CX-1V crystal is manufactured using the STATEK-developed photolithographic process, and was designed utilizing the experience acquired by producing millions of crystals for industrial, commercial, military and medical applications. FEATURES PACKAGE DIMENSIONS actual size side view Miniature tuning fork design High shock resistance Designed for low power applications Compatible with hybrid or PC board packaging Low aging Full military testing available Ideal for battery operated applications Designed and manufactured in the USA PACKAGE HANDLING E F A D B TYP. DIM A B C D E F INCHES .315 .140 .070 .300 .020 .150 mm 8.00 3.56 1.78 7.62 0.51 3.81 C MAX. INCHES .330 .155 .080 .310 .040 .160 mm 8.38 3.94 2.03 7.87 1.02 4.06 The CX crystal is hermetically sealed in a ceramic package. Normal handling and soldering precautions for small, low thermal mass parts are adequate when installing or testing CX crystals. CX crystals may be wave soldered, with proper precaution taken to avoid desoldering the leads. A slow machine rate or too high a pre-heat temperature or solder bath temperature can damage the crystals. Lead to package solder interface temperature should not exceed 175oC, glass lid to package seal rim temperature should not exceed 210oC. If the seal rim reaches temperatures above the maximum specified, the package may lose its hermeticity. Loss of hermeticity results in a frequency decrease and motional resistance increase. EQUIVALENT CIRCUIT Leads 0.013” x 0.018” (0.33 x 0.46 mm) typical. CONVENTIONAL CMOS PIERCE OSCILLATOR CIRCUIT Rf BUFFER OSC Freq (fO) Contact factory for design guidelines C0 1 L1 C1 R1 2 CG AMPLIFIER CS RA R1 Motional Resistance L1 Motional Inductance C1 Motional Capacitance C0 Shunt Capacitance CX-1 CD 10101 - Rev B RSG Electronic Components GmbH, Sprendlinger Landstr. 115, 63069 Offenbach, Germany, Tel. +49 69 - 984047-0, Fax: +49 69 - 9840-77, www.rsg-electronic.de SPECIFICATIONS Specifications are typical at 25oC unless otherwise noted. Specifications are subject to change without notice. Frequency Range 10 kHz to 600 kHz Calibration Tolerance* A,B, or C (see below) Figure 1 Motional Resistance (R1) MAX.: 2x Typ.@10-169.9 kHz 2.5x Typ.@170-600 kHz Motional Capacitance (C1) Figure 2 Quality Factor (Q) Figure 3 Min. is 0.25x Typ. Shunt Capacitance (C0) 2.0 pF MAX. Drive Level 0.5 W MAX.@10-24.9 kHz 1.0 W MAX.@ 25-600 kHz Turning Point (T )** Figure 4 O Temperature Coefficient (k) -0.035 ppm/0C2 Aging, first year 5ppm MAX. Shock, survival*** 1,000g 1msec., 1/2 sine Vibration, survival*** 20g rms 10-2,000 Hz Operating Temperature -10oC to +70oC Commercial -40oC to +85oC Industrial -55oC to +125oC Military Storage Temperature -55oC to +125oC Max Process Temperature See package handling * Tighter frequency calibration available. ** Other turning point available. *** Higher shock and vibration available. FIGURE 1 CX-1V TYPICAL MOTIONAL RESISTANCE (R1) 300 200 100 50 R1 (k ) 20 10 5 2 10 20 50 100 200 600 Frequency (kHz) FIGURE 2 CX-1V TYPICAL MOTIONAL CAPACITANCE (C1) 5 C1 (fF) 2 1.0 0.5 10 20 50 100 200 600 Frequency (kHz) FIGURE 3 CX-1V TYPICAL QUALITY FACTOR (Q) 300 200 CX-1V Crystal Calibration Tolerance at 25oC (in 1000's) 100 50 Frequency Range (kHz) Calibration 10-74.9 A B C + _ + _ + _ 75-169.9 + _ + _ + _ 170-249.9 + _ + _ + _ 250-600 + _ + _ + _ 0.003% 0.01% 0.1% 0.005% 0.01% 0.1% 0.01% 0.02% 0.2% 0.02% 0.05% 0.5% 20 10 20 50 100 200 600 Frequency (kHz) FIGURE 4 CX-1V TYPICAL TURNING POINT TEMP (T0) . Load Capacitance (CL), Used to Calibrate CX-1V (other CL available) Frequency Range (kHz) 10-15.9 16-24.9 25-54.9 Load Capacitance (pF) 11 10 9 Frequency Range (kHz) 55-99.9 100-179.9 180-600 Load TO ( C) 8 5 4 O Capacitance (pF) +80 +70 +60 +50 +40 +30 +20 +10 0 -10 -20 10 20 50 100 200 600 HOW TO ORDER CX-1V-03 LEADED CRYSTALS Frequency (kHz) Note: Frequency (f) deviation from frequency (fo ) @ turning point 2 f-fO = k(T-T ) O fO CX-1V “S” if special or custom design. Blank if Std. -03 Side Leads 32.768 kHz (A /I ) Temp. Range: C = Commercial I = Industrial M = Military S = Specify *Other calibration fill in ppm. Frequency Calibration Tolerance* @ 250C (A) (B) (C) PACKAGING CX-1V-03 -Tray Pack (Standard) 10101 - Rev B RSG Electronic Components GmbH, Sprendlinger Landstr. 115, 63069 Offenbach, Germany, Tel. +49 69 - 984047-0, Fax: +49 69 - 9840-77, www.rsg-electronic.de