CXOHT5SHGN

HIGH TEMPERATURE OSCILLATORS High Temperature/High Shock DESCRIPTION CXOHT 300 kHz - 50 MHz CXOMHT 300 kHz - 50 MHz CXOXHT 1 MHz - 50 MHz An increasing number of applications require the use of hightemperature oscillators. For these applications, Statek offers the CXOHT, CXOMHT, and CXOXHT oscillators. These oscillators are designed to operate at temperatures up to 200ºC with a total frequency stability of 200 parts-per-million at this temperature. The CXOHT is offered in a 10.16 mm x 4.57 mm package. The CXOMHT oscillator is offered in a 6.50 mm x 5.00 mm package. The CXOXHT oscillator features the smallest size of the three, and is offered in a 3.20 mm x 2.50 mm package. FEATURES 20M 20M Actual Size Top View Side View 1. 2. 3. 4. Actual Size Top View Side View Actual Size Top View Side View PIN CONNECTIONS O High temperature operation up to 200 C Excellent stability over temperature Fast start-up High shock resistance CMOS and TTL compatible Optional output enable/disable Low EMI emission Hermetically sealed ceramic package APPLICATIONS Enable/Disable (E) or No Connection (N) Ground Output VDD DIMENSIONS CXOHT MAXIMUM DIM A B C (SM1) D E F CXOMHT inches 0.190 0.055 0.350 0.135 0.060 mm 4.83 1.40 1.60 8.89 3.43 1.52 0.405 10.29 CXOMHT MAXIMUM inches 0.263 0.204 0.055 0.063 0.065 0.070 mm 6.68 5.18 1.40 1.60 1.65 1.78 CXOXHT MAXIMUM inches 0.136 0.107 0.043 0.048 0.041 0.031 mm 3.40 2.70 1.09 1.21 1.10 0.85 Industrial Downhole instrumentation Rotary shaft sensors Underground boring tools PACKAGE DIMENSIONS CXOHT 3 2 E C (SM3/SM5) 0.063 CXOXHT D 2 3 A 4 TOP C 3 3 D 4 BOTTOM 2 A TOP 3 BOTTOM D BOTTOM A TOP E 1 4 D 1 B 2 2 1 4 B 1 C 1 F 4 B C E SUGGESTED LAND PATTERN CXOHT 0.275 (6.99) 0.067 (1.70) CXOMHT 0.070 (1.78) CXOXHT 0.141 (3.6) 0.065 (1.65) 0.130 (3.30) 0.070 (1.78) 0.060 (1.52) 0.201 (5.11) 0. 36 (3.45) 1 0.110 (2.9) 0.031 (0.8) 0.039 (1.05) 0.051 (1.3) 0.039 (1.0) GRID PLACEMENT COURTYARD 0.140 (3.56) 0.135 (3.43) inches (mm) inches (mm) 0.137 (3.48) GRID PLACEMENT COURTYARD inches (mm) 10180 - Rev A SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Specifications are typical at 25OC unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 Calibration Tolerance Frequency Stability Over Temperature Total Tolerance2 Supply Current (Typical) 3.3 V ± 10% 5.0 V ± 10% ± 50 ppm, or tighter as required ± 100 ppm for 25 C to 150 C ± 150 ppm for 25OC to 175OC ± 175 ppm for 25OC to 200OC O O Supply Voltage VDD Storage Temperature Maximum Process Temperature -0.3 V to 7.0 V -55OC to 125OC 260OC, 20 seconds ENABLE/DISABLE OPTIONS (E/T/N) ± 200 ppm for 25OC to 200OC 3.3 V 5.0 V 24 MHz 3.0 mA 8.0 mA 32 MHz 5.0 mA 10.0 mA 50 MHz 6.0 mA 14.0 mA 120 MHz 23.0 mA 39.0 mA Output Load (CMOS) 15 pF Start-up Time 5 ms MAX Rise/Fall Time 6 ns MAX Duty Cycle 40% MIN, 60% MAX Aging, first year 10 ppm MAX at 25OC Aging, 1,000 Hrs 100 ppm MAX at 200OC Shock, survival3 Std: 3,000 g, 0.3 ms, 1/2 sine HG: 10,000 g, 0.3 ms, 1/2 sine 4 20 g, 10-2,000 Hz swept sine Vibration, survival Operating Temp Range -55OC up to 200OC 1. All frequencies, voltages, temperature ranges and enable/disable options may not be available. Contact factory. 2. Total Tolerance = Calibration Tolerance + Frequency Stability over temperature. 3. For non-high-shock CXOHT and CXOMHT oscillators only. The specification for CXOXHT oscillators is 5,000 g, 0.3 ms, 1/2 sine. 4. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing available. Note: All parameters are measured at ambient temperature with a 10 M!, 15 pF load. Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. COMPARISON OF ENABLE/DISABLE OPTIONS E AND T E T When enabled (PIN 1 is high*) Output Oscillator Current consumption Freq. output Oscillates Normal Freq. output Oscillates Normal When disabled (PIN 1 is low) Output Oscillator Current consumption High Z state Stops Very low High Z state Oscillates Lower than normal When re-enabled (PIN 1 changes from low to high) Output recovery Delayed Immediate PACKAGING OPTIONS * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. CXOHT, CXOMHT, CXOXHT - Tray Pack - 16 mm tape, 7” or 13” reels Per EIA 481 (see Tape and Reel data sheet # 10109) HOW TO ORDER CXOHT, CXOMHT and CXOXHT OSCILLATORS CXOMHT CXOHT CXOMHT CXOXHT Supply Voltage 4 = 3.3 V 5 = 5.0 V 4 S “S” if special or custom design. Blank if Std. E Enable/Disable Option E or T or N SM3 Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 20.0M, Frequency M = MHz K = kHz Calibration Tolerance @ 250C (in ppm) / / 200 Total Frequency Tolerance (in ppm) / H Temp. Range: H = 250C to 2000C S = Customer Specified Temp. Range HG = High Shock otherwise leave blank. OR 25 Calibration Tolerance @ 250C (in ppm) Frequency Stability over Temp. Range (in ppm) / 175 / Total Frequency Tolerance (in ppm) / H Temp. Range: H = 250C to 2000C S = Customer Specified Temp. Range Frequency Stability over Temp. Range (in ppm) Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ■ ■ ■ ■ ■ Änderungen vorbehalten / subject to change without notice