CXOMHGSESM5

CXOMHG OSCILLATOR 300 kHz to 120 MHz ™ High Shock, Low Profile, Miniature Surface Mount Crystal Oscillator DESCRIPTION Intended for applications requiring shock survivability to 10,000 g (and higher), Statek’s surface-mount CXOMHG oscillators are high-shock versions of the CXOM oscillators. These oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. FEATURES GM M 4.19 actual size side view High shock resistance Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques Hermetically sealed ceramic package CMOS and TTL compatible Low power consumption Optional Output Enable/Disable with Tri-State Low EMI emission Full military testing available APPLICATIONS A TOP PACKAGE DIMENSIONS D 2 BOTTOM 3 1 4 D Military & Aerospace Smart munitions Projectile electronics Industrial Engine control Down-hole drilling DIM A B C (SM1) B C E TYPICAL inches 0.256 0.197 0.051 0.055 0.055 0.060 mm 6.50 5.00 1.30 1.40 1.40 1.52 MAXIMUM inches 0.263 0.204 0.055 0.063 0.065 0.070 mm 6.68 5.18 1.40 1.60 1.65 1.78 C (SM3/SM5) SUGGESTED LAND PATTERN 0.067 (1.70) 0.070 (1.78) D E PIN CONNECTIONS 0.065 (1.65) 1. Enable/Disable (E or T) or not connected (N) 2. Ground 3. Output 4. VDD 0.201 (5.11) 0.136 (3.45) 0. 37 (3.48) 1 inches (mm) ■ Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ■ ■ ■ ■ GRID PLACEMENT COURTYARD 10160 Rev A S YS TEM C ERT I F I C AT N IO 01 Pb IS O 90 Änderungen vorbehalten / subject to change without notice SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS O Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 Calibration Tolerance2 Frequency Stability Over Temperature3 Supply Current (Typical) 5.0 V + _ + _ Supply Voltage VDD -0.5V to 7.0V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC fo 20 seconds ENABLE/DISABLE OPTIONS (E/T/N) 100 ppm 50 ppm for Commercial + _ 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 4 mA 24 MHz 8 mA 30 MHz 10 mA 40 MHz 12 mA 50 MHz 14 mA 15 pF 5 ms MAX 6 ns MAX 40% MIN, 60% MAX 10 ppm MAX 10,000 g, 0.3 ms, 1/2 sine 20 g, 10-2,000 Hz swept sine O O Output Load (CMOS)4 Start-up Time Rise/Fall Time Duty Cycle Aging, first year Shock, survival 5 Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table compares the E and T versions. COMPARISON OF ENABLE/DISABLE OPTIONS E AND T E When enabled (PIN 1 is high*) Output Oscillator Current consumption When disabled (PIN 1 is low) Output Oscillator Current consumption High Z state Stops Very low Freq. output Oscillates Normal T Vibration, survival6 Operating Temp Ranges -10 C to +70 C (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 3.3 V, see CXO3MHG data sheet. For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory for requirements above 10,000 g. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. Freq. output Oscillates Normal High Z state Oscillates Lower than normal When re-enabled (PIN 1 changes from low to high) Output recovery Delayed Immediate PACKAGING OPTIONS CXOMHG - Tray Pack - 16 mm tape, 7˝or 13˝ reels Per EIA 418 (see Tape and Reel data sheet 10109) * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. HOW TO ORDER CXOMHG SURFACE MOUNT CRYSTAL OSCILLATORS CXOMHG S “S” if special or custom design. Blank if Std. T Enable/Disable Option E, T, or N SM3 Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M Frequency K = kHz M = MHz , 100 Calibration Tolerance @ 250C (in ppm) / 100 / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified Frequency Stability over Temp.Range (in ppm) OR / / 200 Total Frequency Tolerance (in ppm) / I Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ■ ■ ■ ■ ■ Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10160 Rev A S YS TEM C ERT I F I C AT N IO Änderungen vorbehalten / subject to change without notice 01 Pb IS O 90