CXOMSNSM5

CXOM OSCILLATOR 300 kHz to 120 MHz ™ Low Profile Miniature Surface Mount Crystal Oscillator DESCRIPTION Statek’s surface-mount CXOM oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. FEATURES Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques CMOS and TTL compatible Low power consumption Optional Output Enable/Disable with Tri-State Low EMI emission High shock resistance Full military testing available Hermetically sealed ceramic package APPLICATIONS A TOP GM M 4.19 actual size side view DIMENSIONS D 2 BOTTOM 3 Military & Aerospace Smart Munitions Cockpit Systems Navigation Industrial, Computer & Communications Industrial Controls Instrumentation Microprocessor Clocks Medical Infusion Pumps SUGGESTED LAND PATTERN 0.067 (1.70) 0.070 (1.78) 1 4 D B C E TYPICAL DIM A B inches 0.256 0.197 mm 6.50 5.00 1.30 1.40 1.40 1.52 MAXIMUM inches 0.263 0.204 0.055 0.063 0.065 0.070 mm 6.68 5.18 1.40 1.60 1.65 1.78 0.051 C (SM1) C (SM3/SM5) 0.055 D E 0.055 0.060 PIN CONNECTIONS 0.065 (1.65) 1. Enable/Disable (E or T) or not connected (N) 2. Ground 0.201 (5.11) 0.136 (3.45) 3. Output 4. VDD 0. 37 (3.48) 1 inches (mm) ■ GRID PLACEMENT COURTYARD S 10116 Rev E YS Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ■ ■ ■ ■ TEM C ERT I F I C AT N IO IS O 90 01 Änderungen vorbehalten / subject to change without notice SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS O Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 Calibration Tolerance2 Frequency Stability Over Temperature3 Supply Current (Typical) 5.0 V + _ + _ + _ Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC for 20 seconds 100 ppm ENABLE/DISABLE OPTIONS (E/T/N) 50 ppm for Commercial 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 4 mA 24 MHz 8 mA 30 MHz 10 mA 40 MHz 12 mA 50 MHz 14 mA 15 pF 5 ms MAX 6 ns MAX 40% MIN, 60% MAX 10 ppm MAX 3,000 g, 0.3 ms, 1/2 sine 20 g, 10-2,000 Hz swept sine Output Load (CMOS)4 Start-up Time Rise/Fall Time Duty Cycle Aging, first year Shock, survival 5 Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. COMPARISON OF ENABLE/DISABLE OPTIONS E AND T E When enabled (PIN 1 is high*) Output Oscillator Current consumption When disabled (PIN 1 is low) Output Oscillator Current consumption High Z state Stops Very low Freq. output Oscillates Normal T Vibration, survival6 Operating Temp Ranges -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 3.3 V, see CXO3M data sheet (10126). For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory about CXOMHG. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. Freq. output Oscillates Normal High Z state Oscillates Lower than normal When re-enabled (PIN 1 changes from low to high) Output recovery PACKAGING OPTIONS Delayed Immediate CXOM - Tray Pack - 16mm tape, 7˝ or 13˝ reels Per EIA 418 (see Tape and Reel data sheet 10109) * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. HOW TO ORDER CXOM SURFACE MOUNT CRYSTAL OSCILLATORS CXOM S “S” if special or custom design; otherwise blank. T Enable/Disable Option E, T, or N SM3 Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M , Frequency K = kHz M = MHz 100 Calibration Tolerance @ 250C (in ppm) / 100 Frequency Stability over Temp.Range (in ppm) / / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 200 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified S Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ■ ■ ■ ■ ■ 10116 Rev E YS TEM C ERT I F I C AT N IO IS O Änderungen vorbehalten / subject to change without notice 90 01