LEB100F-0524-SN

Rugged PCB type Ordering information LEB100F R LEB 100 1 2 3 F 4 -05 5 24 6 -O Recommended Noise Filter NAC-06-472 High voltage pulse noise type : NAP series Low leakage current type : NAM series *The Noise Filter is recommended *to connect with several devices. 1 Series name 2 Output wattage 3 Universal input 4 V1 Output voltage 5 V2 Output voltage 6 Optional *1 G :Low leakage current R :with Remote ON/OFF S :with Chassis SN :with Chassis & cover T :Vertical terminal block Y :with Potentiometer Z :with ZT MODEL DC OUTPUT V1 V2 LEB100F-0512 +5V 5A +12V 5(Peak 10)A LEB100F-0324 +3.3V 5A +24V 4(Peak 7)A LEB100F-0524 +5V 5A +24V 4(Peak 7)A LEB100F-0530 +5V 5A +30V 3.2(Peak 5.6)A LEB100F-0536 +5V 5A +36V 2.7(Peak 4.7)A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] FREQUENCY[Hz] INPUT ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *2 TOTAL OUTPUT WATTAGE[W] *3 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *4 RIPPLE[mVp-p] -10 - 0C *4 0 to +50C *4 RIPPLE NOISE[mVp-p] -10 - 0C *4 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *5 START-UP TIME[ms] *6 HOLD-UP TIME[ms] *6 OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] V1 OVERCURRENT PROTECTION V2 V1 OVERVOLTAGE PROTECTION V2 REMOTE ON/OFF INPUT-OUTPUT -RC *7 INPUT-FG OUTPUT-RC-FG *7 OUTPUT-OUTPUT(V1 -RC-V2) *7 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] ACIN 100V ACIN 200V LEB100F-0512 LEB100F-0324 LEB100F-0524 LEB100F-0530 AC85 - 264 1f or DC 120 - 370 1.2typ (Io=100%) 1.4typ (Io=100%) 0.6typ (Io=100%) 0.7typ (Io=100%) 50/60 (47 - 63) or DC 74typ (Io=100%) 78typ (Io=100%) 78typ (Io=100%) 78typ (Io=100%) 76typ (Io=100%) 80typ (Io=100%) 80typ (Io=100%) 80typ (Io=100%) 0.98typ 0.99typ 0.93typ 15typ (Io=100%) (At cold start) (Ta=25 C) 30typ (Io=100%) (At cold start) (Ta=25 C) 0.75max (60Hz, According to IEC60950 and DEN-AN) +5 +12 +3.3 +24 +5 +24 +5 +30 0-5 0 - 5 (Peak 10) 0 - 5 0 - 4 (Peak 7) 0 - 5 0 - 4 (Peak 7) 0 - 5 0 - 3.2 (Peak 5.6) 85 (Peak 145) 100 (Peak 172) 100 (Peak 172) 100 (Peak 172) 20max 48max 20max 96max 20max 96max 20max 120max 40max 100max 40max 150max 40max 150max 40max 180max 80max 120max 80max 120max 80max 120max 80max 200max 140max 160max 140max 160max 140max 160max 140max 240max 120max 150max 120max 150max 120max 150max 120max 300max 160max 180max 160max 180max 160max 180max 160max 360max 50max 120max 50max 240max 50max 240max 50max 300max 60max 150max 60max 290max 60max 290max 60max 350max 20max 48max 20max 96max 20max 96max 20max 120max 250max 500max 250max 500max 250max 500max 250max 500max 40typ 20typ 40typ 20typ 40typ 20typ 40typ 20typ 4.5 - 5.5 Fixed 2.85 - 3.60 Fixed 4.5 - 5.5 Fixed 4.5 - 5.5 Fixed 11.5 - 12.5 xx 23.0 - 25.0 xx 23.0 - 25.0 xx 28.7 - 31.5 xx Works over 105% of rating current and recovers automatically Works over 101% of peak current and recovers automatically Works over 115% of rating, by zener diode clamping Works at 115 - 140% of rating Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL, EN60950-1, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Complies with IEC61000-3-2 75X35X222mm (WXHXD) /420g max (without chassis and cover) Convection *6 *7 * * * with the input voltage held constant at the rated input/output. ACIN 100V,lo=100% Applicable when remote control (optional) is added. Series/Parallel operation is not possible. Derating is required when operated with chassis and cover. A sound may occur from power supply at peak loading. LEB100F-0536 78typ (Io=100%) 80typ (Io=100%) LEB OUTPUT +5 +36 0-5 0 - 2.7 (Peak 4.7) 100 (Peak 172) 20max 144max 40max 180max 80max 200max 140max 240max 120max 300max 160max 360max 50max 300max 60max 350max 20max 144max 250max 500max 40typ 20typ 4.5 - 5.5 Fixed 34.5 - 37.5 xx PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 *4 Specification is changed at option, refer to Instruction Manual 5. Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 4. In detail. Refer to Instruction Manual 2.2 in detail. This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM101). *5 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, F-2 LEB100F External view + 235-0.5 8 4-M4 Mounting Hole Name plate 20 30 4-º3.5 Mounting Hole CN2 2-º4.5 + 65-0.5 CN1 CN3 CN4 5 Voltage adjust(V1) (197) 5 + 212 - 0.5 222 Connector for Remote ON/OFF (option) Connector for -Z (option) º4.5 2-M4 Mounting Hole CN4 CN3 RC(-) (17) CN4 252 + 235-0.5 8 32 4.5 4.5 CN3 5 3 1 FG AC (N) AC (L) 4 5 8 + 45-0.5 + 25-0.5 C1 19 G2 +V2 G1 +V1 1 CN1 CN2 42 15 20 85 75 (Lead) 3max PCB t=1.6 + COM - RC(+) PIN CONNECTION I / O Connector Mating Connector Terminal Chain : SVH-21T-P1.1 CN1 VHR-5N B3P5-VH Loose: BVH-21T-P1.1 Chain : SVH-21T-P1.1 CN2 VHR-8N B8P-VH Loose: BVH-21T-P1.1 Chain : SXH-001T-P0.6 CN3 XHP-2 (Option) B2B-XH-A Loose: BXH-001T-P0.6 Chain : SXH-001T-P0.6 CN4 XHP-3 (Option) B3B-XH-A Loose: BXH-001T-P0.6 (Mfr: J.S.T.) CN1 Pin No. Input 1 AC(L) 2 3 AC(N) 4 5 FG CN2 Pin No. Output G2 1, 2 V2 3, 4 G1 5, 6 V1 7, 8 CN3 (Option) Pin No. Remote ON/OFF 1 RC(+) 2 RC(-) CN4 (Option) Pin No. -Z 1 + COM 2 3 ¶Weight: 420g or less (Without chassis and cover) ¶Tolerance: t1 ¶Dimensions in mm. ¶PCB Material : CEM3 ¶Chassis and cover is optional. ¶Mounting torque: 1.5N · m(16kgf · cm)max ¶Keep drawing current per pin below 5A for CN2 Performance data 46 LEB ¡EFFICIENCY (LEB100F-0524) 82 ¡RISE TIME & FALL TIME (LEB100F-0524) +24V ACIN 100V Io=100% 80 78 EFFICIENCY 76 DC Output +5V AC Input 74 72 Load factor100% Load factor 50% 100 140 180 220 260 300 100ms/DIV 20ms/DIV 70 60 INPUT VOLTAGE V ¡INPUT HARMONIC CURRENT (LEB100F-0524) 10 ¡INPUT HARMONIC CURRENT (LEB100F-0524) 10 A HARMONIC CURRENT HARMONIC CURRENT 1 Load factor 100% Input voltage AC 100V A Harmonic current standard class A (at odd number) 1 Harmonic current standard class A (at odd number) Load factor 100% Input voltage AC 230V 0.1 0.1 0.01 0.01 0.001 0 10 20 30 40 0.001 0 10 20 30 40 HARMONIC ORDER HARMONIC ORDER Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ■ ■ ■ ■ ■ F-3 Änderungen vorbehalten / subject to change without notice