400YXA1MPCST16.3X11

Mess toyogawa ALUMINUM ELECTROLYTIC CAPACITORS SPECIFICATION SHEET CUSTOMER PART No. Rubycon PART No. 400 YXA 1 M PCS T1 6.3X11 DRAWING No. REE – 114486 ISSUE DATE 10 December 2013 ISSUE No. 1 RUBYCON CORPORATION ENGINEERING DIVISION 1938-1, NISHIMINOWA, INA-SHI, NAGANO-KEN, JAPAN TEL No. 0265-72-7116 FAX No. 0265-73-3380 YUICHI KOBAYASHI DESIGN TETSUYA MIZU CHECK HIROKAZU KOUMURA APPROVAL PAGE ALUMINUM ELECTROLYTIC CAPACITORS 400 WV 1.Dimensions 1 MFD Style Operating Temperature Range Reference Standard 1 Sleeve 2 Case (YXA SERIES) 3 Lead Wire 1/6 CE 04 -25C ~ +105C JIS C 5141 , JIS C 5102 P.E.T. Aluminum CP Wire Tin plated unit : mm 2 3  d+/-0.05 F+/- 0.5 1 L+2.0MAX 2.Electrical Performance Table-1 CAPACITANCE NOMINAL TOLERANCE CAPACITANCE (%) (F) 20C, 120Hz 1 4MIN 15MIN SURGE VOLTAGE (V.DC) RATED VOLTAGE (V.DC) -20 ~ +20 400 450 D LEAKAGE CURRENT (A MAX) 20C 1min 5min 80.0 27.0 DIMENSIONS (mm) IMPEDANCE RATIO 120Hz Z-25C/Z20C D L F d 6 6.3 11 2.5 0.5 3.Marking : Unless otherwise specified, capacitor shall be clearly marked the following items on its body. Sleeve color : Black Lettering color : White (1) Trade mark (2) Rated Voltage 400V (3) Nominal Capacitance 1 F (4) Polarity (Negative Polarity) (5) Series YXA (6) Lot. No. (7) Maximum Operating temperature (8) PET sleeve mark 105C PET 4.Vent A safety vent shall be provided. YXA SERIES RUBYCON CORPORATION +0.5MAX D.F. tan  MAX 20C 120Hz MAX RIPPLE CURRENT (mA rms) 105C 120Hz 0.24 16 PAGE 2/6 5.Load Life test Capacitor under test shall be applied the rated voltage continuously through 1000 ohm series protective resistor (with maximum ripple current) at 1052C. After 2000 720 hours, capacitor shall be stored in standard condition for 2 hours or more, then capacitor shall meet following requirement. Capacitance Change : within 25% of the initially measured value. Dissipation Factor : less than 200% of the specified value. Leakage Current : less than the specified value. Appearance : notable changes shall not be found. (Except sleeve condition) 6.Shelf life test Capacitors shall be stored at 1052C with no voltage applied for 1000 480 hours. After the test and returned in standard condition for 1 to 2 hours and the capacitor shall meet following requirements. (If any doubt arises on the judgment, the capacitors shall be subjected to voltage treatment specified in JIS C 5141,5.2.) Capacitance Change : within 25% of the initially measured value. Dissipation Factor : less than 200% of the specified value. Leakage Current : less than the specified value. Appearance : notable changes shall not be found. 7.Correction factor for ripple current The maximum permissible ripple current is the maximum A.C. current at 120Hz and can be applied at maximum operating temperature. The combined value of D.C. voltage and the peak A.C. voltage shall not exceed the rated voltage and shall not be reverse voltage. < Frequency Coefficient > Freq. (Hz) 60(50) 120 500 1k 10k Multiplier 0.50 1.00 1.20 1.30 1.50 < Temperature Coefficient > Ambient Temperature(C) 105 85 65 Coefficient 1.0 1.7 2.1 Temperature coefficient shows a limit of ripple current exceeding the rated ripple current that can be passed through a capacitor at each temperature when the life expectancy of a capacitor becomes to be nearly equal with the lifetime at the rated maximum operating temperature. Ripple voltage with wide amplitude Use of aluminum electrolytic capacitor under ripple voltage with wide amplitude is equivalent to quick charge-discharge operation. When ripple voltage with the amplitude over 70Vp-p is expected for the products with rated voltage over 100V, please contact us. 8.Operation of safety vent (S-measure) Capacitors (The examination number:10) shall be added DC overvoltage(WV×1.5) below by using DC constant power supply at5-35deg.C. Maximum D.C. Current is 1A After test either of the following specification shall be satisfied. *When the safety vent does not open even 10 minutes after beginning this test the test may be ended. *Even if electrolyte was discharged after a pressure relief vent of capacitor had operated. the percentage of capacitors without short-circuit (normal vent operation)shall be more than 60%.The percentage of normal vent operation shall be more than 80% on an accumulation of regular test. YXA SERIES RUBYCON CORPORATION PAGE 3/6 9. Notes on use of aluminum electrolytic capacitors (1) Charge and discharge Do not use for the circuit that repeats quick charge or discharge (2) External stress Do not apply excessive force of pushing, pulling bending, and/or twisting to the main body, lead wire and terminals. (3) Heat resistance at soldering process In the soldering process of PC board with Capacitors mounted, secondary shrinkage or crack of sleeve may be observed when soldering temperature is too high and /or soldering time is too long. If lead wire of other components or pattern of double sided PC board touches the capacitor, the similar failure may be also originated at pre-heating, heating at hardening process of adhesive and soldering process. (4) Insulation and PC board mounting Sleeve is for marking purpose only. It is not recognized as insulation materials. When double sided PC board is employed, note that it could cause a short circuit if lead wire of other components or pattern of double sided PC board touches capacitor. Please avoid circuit pattern runs underneath capacitor. In addition, case and cathode terminal are not insulated. (5) Adhesives and coating materials Do not use the adhesives and coating materials that contain halogenated organic solvents or chloroprene as polymer. (6) Storage Keep at a normal temperature and humidity. During a long storage time, leakage current will be increased. To prevent heat rise or any trouble that high leakage current possibly causes, voltage treatment is recommended for the capacitors that have been stored for a long time. . *Aluminum electrolytic capacitors should not be stored in high temperatures or where there is a high level of humidity. The suitable storage condition is 5C-35C and less than 75% in relative humidity. *Aluminum electrolytic capacitors should not be stored in damp conditions such as water, saltwater spray or oil spray. *Do not store aluminum electrolytic capacitors in an environment full of hazardous gas (hydrogen sulfide, sulfurous acid gas, nitrous acid, chlorine gas, ammonia or bromine gas). *Aluminum electrolytic capacitors should not be stored under exposure to ozone, ultraviolet rays or radiation. (7) Fumigation and halogenated flame retardant It may cause corrosion of internal electrodes, aluminum cases and terminal surface when the following conditions exist. *Fumigation of wooden pallets before shipment to disinfect vermin. *Existence of components or parts that contain halogenated flame retardant agent (bromine etc.) together with capacitors. *When halogenated detergents or antiseptics for preventing infection of epidemic diseases contact directly to capacitors. (8) PC board cleaning after soldering Please consult us when cleaning is subjected. Guide to application except the above are described in our catalog and EIAJ RCR-2367C. EIAJ RCR-2367C: “Safety Application Guide for fixed aluminum electrolytic capacitors for use in electronic equipment." Published by Japan Electronics and Information Technology Industries Association. YXA SERIES RUBYCON CORPORATION PAGE 4/6 TAPING SPECIFICATION OF RADIAL LEAD TYPE ALUMINUM ELECTROLYTIC CAPACITORS 1.Scope This specification covers taped radial lead type electrolytic capacitors, with case dia of  6.3 mm. 2.Requirements. 2-1. Body tape requirements are shown in 6/6 page. 2-2. All polarized capacitors must be oriented in one direction. 2-3. Leader tape shall be provided before the first capacitor and after the last one on tape at minimum length of 3 feed holes. 2-4 Maximum of 3 consecutive missing capacitors are permitted while one pack quantity meets the specification in para.4. 2-5. Mounting tape shall be spliced as shown in Fig.1. Mounting tape shall not be over lapped. lead wire adhesive tape mounting tape Fig.1 splicing tape mounting tape connection of adhesive tape connection of mounting tape 2-6. Defective capacitors shall be pulled out or clipped from the mounting tape. Remaining protrusion of the leads shall not exceed 2mm from edge of the tape, when clipped. 3. Adhesion test of mounting tape 3-1. Adhesive tape on the mounting tape shall not a tear off at the force of less than 3N {0.3kgf} when tested in a manner shown in Fig.2. 3-2. Capacitors shall not be pulled out of the tape with a following load applied to the capacitor body in a manner shown in Fig.3. Dia   8mm 10N {1.0kgf} push-pull scale pull force adhesive tape Fig.2 YXA SERIES pull force mounting tape (to fixed) RUBYCON CORPORATION fixed Fig.3 PAGE 4.Package Taped capacitors shall be packed in a carton shown in Fig.4, with tape ammunition. Packed cartons shall be marked at least polarity, rated voltage, nominal capacitance and quantity. 330 MAX WP MAX 340 MAX Fig.4 STANDARD PACKING QUANTITY YXA SERIES CASE DIA QUANTITY WP(mm) 6.3X11 2000 54 RUBYCON CORPORATION 5/6 PAGE CODE : T1 6/6 ( Positive leading ) LEAD TYPE ( DIA. 6.3 ) p p2 h h p p L  D H d F w1 w0 p0  D0 t L1 w w2 p1 Symbol d L P P0 P1 P2 F W W0 W1 W2 H L1 D0 h p t YXA Case Dia  mm 6.3 0.5 0.05 13.0 MAX 12.7 1.0 12.7 0.2 5.1 0.5 6.35 1.0 0.8 2.5  0.2 18.0 0.3 5.0 MIN 9.0 0.5 1.5 MAX 18.5 0.75 0.5 MAX 4.0 0.2 1.0 MAX 1.0 MAX 0.6 0.3 SERIES Remarks Dia of lead Height of body Distance from center to center of body Distance from center to center of driving hole Distance between center of driving hole and lead Distance between center of driving hole and body Lead spacing Width of mounting tape Width of adhesive tape Distance between center of driving hole and edge of mounting tape Max. allowable distance between mount and adhesive tape side Distance between center of driving hole and bottom of body Protrusion of lead Dia. of driving hole Off alignment of body Off alignment of body Sum of thickness for mounting and adhesive tape without lead dia. RUBYCON CORPORATION