420HXW110MLT512.5X50

Messrs. Shenzhen Onstone Technology Co.Ltd. ALUMINUM ELECTROLYTIC CAPACITORS REFERENCE SHEET RoHS Compliance CUSTOMER PART No. Rubycon PART No. 420 HXW 110 M LT5 12.5X50 ISSUE No.1 DRAWING No. RER-210444 ISSUE DATE 07 April 2020 RUBYCON CORPORATION ENGINEERING DIVISION 1938-1, NISHIMINOWA, INA-SHI, NAGANO-KEN, JAPAN TEL No. 0265-72-7116 FAX No. 0265-73-3380 YOSHIHIRO KITAHARA DESIGN KAZUHIRO YONEYAMA CHECK YOSHINORI SASAKI APPROVAL RTW-1004-2 Page 1 Aluminum electrolytic capacitor Reference Sheet Drawing No.： RER-210444 420 HXW 110 M LT5 12.5X50 Issue No. ：1 1.Scope This specification covers polarized aluminum electrolytic capacitors with non-solid electrolyte for use in electronic equipments. Style：CE 04 (Radial Leaded) Reference Standard : JIS C 5101-1 Fixed capacitors for use in electronic equipment – Part 1 : Generic specification Fixed capacitors for use in electronic equipment - Part 4 : Sectional specification: Reference Standard : JIS C 5101-4 Aluminum electrolytic capacitors with solid (MnO2) and non-solid electrolyte 2.Numbering System Rated Series Voltage 420 HXW Capacitance 110 LT5 Lead Forming  Size 12.5X50 Unit : mm 2 3 F±0.5  D +0.5max. 1 Option  d± 0.05 3.Diagram of dimensions Capacitance Tolerance M L+ max. 15 min. 4 min. Dimensions D L F d α 12.5 50 5 0.6 2 ① Sleeve P.E.T. ② Case Aluminum ③ Lead Wire Copper clad Tin plated steel wire Pressure relief vent shall be provided. 4.Marking Unless otherwise specified, capacitor shall be clearly marked the following items on its body. Sleeve color: Black, Lettering color: White (1)Trade mark (2)Rated Voltage 420V (3)Nominal Capacitance 110μF (4)Polarity (Negative Polarity) (5)Series HXW (6)Lot Number (7)Upper Category 105°C 　Temperature (8)PET sleeve mark PET 5.Electrical Performance Table-1 Category Temperature Range Nominal Capacitance 20°C, 120Hz Capacitance Tolerance Rated Voltage Dissipation Factor (tanδ) Rated Ripple Current Impedance Ratio 120Hz (°C) 110 (μF) -20 ~ 20 (%) 420 (V.DC) 470 (V.DC) 20°C, 5min. 644 (μA max.) Surge Voltage Leakage Current -40 ~105 20°C, 120Hz 0.25 (max.) 105°C, 120Hz 860 (mAr.m.s.) Z-25°C/Z20°C 6 (max.) Z-40°C/Z20°C 10 (max.) RUBYCON CORPORATION RTW-1004-2 Page 2 Aluminum electrolytic capacitor Reference Sheet Drawing No.： RER-210444 HXW series Issue No. ：1 6.　PERFORMANCE Table－2 1 Endurance Capacitor under the test shall be applied the rated voltage continuously through 1000Ω series protective resistor (with rated ripple current) at following temperature and time. After the test and returned in standard condition for 1 to 2 hours, and the capacitor shall meet following requirements. 105 ±2°C 　　Temperature： Time： 2000 +72 0 h 2 Shelf Life Test Leakage Current Not more than the specified value Capacitance Change Within ±20% of the initial value Dissipation Factor Not more than 200% of the specified value Appearance No visible damage and no leakage of electrolyte. Capacitor shall be stored at following temperature and time with no voltage applied . After the test and returned in standard condition for 1 to 2 hours and the capacitor shall meet following requirements. (If any doubt arises on the judgment, the capacitors shall be pre-conditioning.) 105 ±2°C 　　Temperature： Time： 500 +24 0 h 3 Rated Ripple Current Leakage Current Not more than the specified value Capacitance Change Within ±20% of the initial value Dissipation Factor Not more than 200% of the specified value Appearance No visible damage and no leakage of electrolyte. (1) The rated ripple current is the maximum A.C. current at 120Hz and can be applied at upper category temperature. (2) The combined value of D.C. voltage and the peak A.C. voltage shall not exceed the rated voltage and shall not be reverse voltage. Frequency (Hz) 60(50) 120 500 1k 10k≤ 0.8 1 1.25 1.4 1.5 Temperature(°C) 105 85 65≥ 1.0 1.7 2.1 Capacitance (μF) 110 Coefficient ◇Temperature coefficient shows a limit of ripple current exceeding the rated ripple current that can be passed through a capacitor at each temperature when the life expectancy of a capacitor becomes to be nearly equal with the lifetime at the rated upper category temperature. ◇Use of aluminum electrolytic capacitor under ripple voltage with wide amplitude is equivalent to quick charge-discharge operation. When ripple voltage with the amplitude over 70Vp-p is expected for the products with rated voltage over 100V, please contact us. RUBYCON CORPORATION RTW-1004-2 Page 3 Aluminum electrolytic capacitor Reference Sheet Drawing No.： RER-210444 HXW series Issue No. ：1 Notes on use of aluminum electrolytic capacitors (1) Charge and discharge Do not use for the circuit that repeats quick charge or discharge. (2) External stress Do not apply excessive force of pushing, pulling bending, and/or twisting to the main body, lead wire and terminals. (3) Heat resistance at soldering process In the soldering process of PC board with Capacitors mounted, secondary shrinkage or crack of sleeve may be observed when soldering temperature is too high and /or soldering time is too long. If lead wire of other components or pattern of double sided PC board touches the capacitor, the similar failure may be also originated at pre-heating, heating at hardening process of adhesive and soldering process. (4) Insulation and PC board mounting Sleeve is for marking purpose only. It is not recognized as insulation materials. When double sided PC board is employed, note that it could cause a short circuit if lead wire of other components or pattern of double sided PC board touches capacitor. Please avoid circuit pattern runs underneath capacitor. In addition, case and cathode terminal are not insulated. (5) Adhesives and coating materials Do not use the adhesives and coating materials that contain halogenated organic solvents or chloroprene as polymer. (6) Storage Keep at a normal temperature and humidity. During a long storage time, leakage current will be increased. To prevent heat rise or any trouble that high leakage current possibly causes, voltage treatment is recommended for the capacitors that have been stored for a long time. (Storage Condition） *Aluminum electrolytic capacitors should not be stored in high temperatures or where there is a high level of humidity. The suitable storage condition is 5°C-35°C and less than 75% in relative humidity. *Aluminum electrolytic capacitors should not be stored in damp conditions such as water, saltwater spray or oil spray. *Do not store aluminum electrolytic capacitors in an environment full of hazardous gas (hydrogen sulfide, sulfurous acid gas, nitrous acid, chlorine gas, ammonia or bromine gas). *Aluminum electrolytic capacitors should not be stored under exposure to ozone, ultraviolet rays or radiation. (7) Fumigation and halogenated flame retardant It may cause corrosion of internal electrodes, aluminum cases and terminal surface when the following conditions exist. *Fumigation of wooden pallets before shipment to disinfect vermin. *Existence of components or parts that contain halogenated flame retardant agent (bromine etc.) together with capacitors. *When halogenated detergents of antiseptics for preventing infection of epidemic diseases contact directly to capacitors. (8) PC board cleaning after soldering Please consult us when cleaning is subjected. *Guide to application except the above are described in our catalog and JEITA RCR-2367D (including any amendments). JEITA RCR-2367D : "Safety application guide for fixed aluminum electrolytic capacitors for use in electronic equipment." 　　　　　　　　　　　　 　Published by Japan Electronics and Information Technology Industries Association. RUBYCON CORPORATION RTW-1004-2