74AUP1G374GW-Q100H

74AUP1G374-Q100 Low-power D-type flip-flop; positive-edge trigger; 3-state Rev. 1 — 19 February 2013 Product data sheet 1. General description The 74AUP1G374-Q100 provides the single D-type flip-flop with 3-state output. The flip-flop stores the state of data input (D) that meets the set-up and hold times requirements on the LOW-to-HIGH CP transition. When pin OE is LOW, the contents of the flip-flop is available at the (Q) output. When pin OE is HIGH, the output goes to the high-impedance OFF-state. Operation of input pin OE does not affect the state of the flip-flop. Schmitt trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. This product has been qualified to the Automotive Electronics Council (AEC) standard Q100 (Grade 1) and is suitable for use in automotive applications. 2. Features and benefits  Automotive product qualification in accordance with AEC-Q100 (Grade 1)  Specified from 40 C to +85 C and from 40 C to +125 C  Wide supply voltage range from 0.8 V to 3.6 V  High noise immunity  Complies with JEDEC standards:  JESD8-12 (0.8 V to 1.3 V)  JESD8-11 (0.9 V to 1.65 V)  JESD8-7 (1.2 V to 1.95 V)  JESD8-5 (1.8 V to 2.7 V)  JESD8-B (2.7 V to 3.6 V)  ESD protection:  MIL-STD-883, method 3015 Class 3A. Exceeds 5000 V  HBM JESD22-A114F Class 3A. Exceeds 5000 V  MM JESD22-A115-A exceeds 200 V (C = 200 pF, R = 0 )  Low static power consumption; ICC = 0.9 A (maximum)  Latch-up performance exceeds 100 mA per JESD 78 Class II  Inputs accept voltages up to 3.6 V  Low noise overshoot and undershoot < 10 % of VCC  IOFF circuitry provides partial Power-down mode operation 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 3. Ordering information Table 1. Ordering information Type number Package 74AUP1G374GW-Q100 Temperature range Name Description Version 40 C to +125 C plastic surface-mounted package; 6 leads SOT363 SC-88 4. Marking Table 2. Marking Type number Marking code[1] 74AUP1G374GW-Q100 aX [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. 5. Functional diagram D 3 D Q 1 CP Q Q 4 1 OE C1 3 D 6 EN CP Logic symbol OE 001aae458 001aae457 Fig 2. CP 4 6 Fig 1. D IEC logic symbol Fig 3. 001aae459 Logic diagram 6. Pinning information 6.1 Pinning $83*4 &3   2( *1'   9&& '   4 DDD Fig 4. Pin configuration SOT363 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 2 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 6.2 Pin description Table 3. Pin description Symbol Pin Description CP 1 clock input (LOW-to-HIGH, edge-triggered) GND 2 ground (0 V) D 3 data input Q 4 3-state flip-flop output VCC 5 supply voltage OE 6 output enable input (active LOW) 7. Functional description Table 4. Function table[1] Operating mode Input OE CP Load and read register L  L Load register and disable output [1] Output D Internal flip-flop l L L  h H H H  l L Z H  h H Z Q H = HIGH voltage level; h = HIGH voltage level one set-up time prior to the HIGH-to-LOW LE transition; L = LOW voltage level; l = LOW voltage level one set-up time prior to the HIGH-to-LOW LE transition; Z = high-impedance OFF-state;  = LOW-to-HIGH clock transition. 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC supply voltage IIK input clamping current VI input voltage IOK output clamping current Conditions VI < 0 V [1] VO < 0 V [1] Min Max Unit 0.5 +4.6 V 50 - mA 0.5 +4.6 V 50 - mA 0.5 +4.6 V - 20 mA VO output voltage Active mode and Power-down mode IO output current VO = 0 V to VCC ICC supply current - 50 mA IGND ground current 50 - mA Tstg storage temperature 65 +150 C - 250 mW total power dissipation Ptot Tamb = 40 C to +125 C [2] [1] The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SC-88 packages: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K. 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 3 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 9. Recommended operating conditions Table 6. Recommended operating conditions Symbol Parameter VCC Conditions Min Max Unit supply voltage 0.8 3.6 V VI input voltage 0 3.6 V VO output voltage Active mode 0 VCC V Power-down mode; VCC = 0 V 0 3.6 V 40 +125 C 0 200 ns/V Typ Max Unit Tamb ambient temperature t/V input transition rise and fall rate VCC = 0.8 V to 3.6 V 10. Static characteristics Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min VCC = 0.8 V 0.70  VCC - - V VCC = 0.9 V to 1.95 V 0.65  VCC - - V Tamb = 25 C VIH VIL VOH VOL HIGH-level input voltage LOW-level input voltage HIGH-level output voltage LOW-level output voltage 74AUP1G374_Q100 Product data sheet VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 0.8 V - - 0.30  VCC V VCC = 0.9 V to 1.95 V - - 0.35  VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V IO = 20 A; VCC = 0.8 V to 3.6 V VCC  0.1 - - V IO = 1.1 mA; VCC = 1.1 V 0.75  VCC - - V IO = 1.7 mA; VCC = 1.4 V 1.11 - - V IO = 1.9 mA; VCC = 1.65 V 1.32 - - V IO = 2.3 mA; VCC = 2.3 V 2.05 - - V VI = VIH or VIL IO = 3.1 mA; VCC = 2.3 V 1.9 - - V IO = 2.7 mA; VCC = 3.0 V 2.72 - - V IO = 4.0 mA; VCC = 3.0 V 2.6 - - V VI = VIH or VIL IO = 20 A; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3  VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.31 V IO = 1.9 mA; VCC = 1.65 V - - 0.31 V IO = 2.3 mA; VCC = 2.3 V - - 0.31 V IO = 3.1 mA; VCC = 2.3 V - - 0.44 V IO = 2.7 mA; VCC = 3.0 V - - 0.31 V IO = 4.0 mA; VCC = 3.0 V - - 0.44 V All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 4 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit II input leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - 0.1 A IOZ OFF-state output current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V - - 0.1 A IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - 0.2 A IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - 0.2 A ICC supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 0.5 A ICC additional supply current VI = VCC  0.6 V; IO = 0 A; VCC = 3.3 V - - 40 A CI input capacitance VCC = 0 V to 3.6 V; VI = GND or VCC - 0.8 - pF CO output capacitance output enabled; VO = GND; VCC = 0 V - 1.7 - pF output disabled; VCC = 0 V to 3.6 V; VO = GND or VCC - 1.5 - pF VCC = 0.8 V 0.70  VCC - - V VCC = 0.9 V to 1.95 V 0.65  VCC - - V VCC = 2.3 V to 2.7 V 1.6 - V V [1] Tamb = 40 C to +85 C VIH VIL VOH VOL HIGH-level input voltage LOW-level input voltage HIGH-level output voltage LOW-level output voltage 74AUP1G374_Q100 Product data sheet - VCC = 3.0 V to 3.6 V 2.0 - - VCC = 0.8 V - - 0.30  VCC V VCC = 0.9 V to 1.95 V - - 0.35  VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V IO = 20 A; VCC = 0.8 V to 3.6 V VCC  0.1 - - V IO = 1.1 mA; VCC = 1.1 V 0.7  VCC - - V IO = 1.7 mA; VCC = 1.4 V 1.03 - - V IO = 1.9 mA; VCC = 1.65 V 1.30 - - V IO = 2.3 mA; VCC = 2.3 V 1.97 - - V IO = 3.1 mA; VCC = 2.3 V 1.85 - - V IO = 2.7 mA; VCC = 3.0 V 2.67 - - V IO = 4.0 mA; VCC = 3.0 V 2.55 - - V IO = 20 A; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3  VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.37 V IO = 1.9 mA; VCC = 1.65 V - - 0.35 V IO = 2.3 mA; VCC = 2.3 V - - 0.33 V IO = 3.1 mA; VCC = 2.3 V - - 0.45 V IO = 2.7 mA; VCC = 3.0 V - - 0.33 V IO = 4.0 mA; VCC = 3.0 V - - 0.45 V VI = VIH or VIL VI = VIH or VIL All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 5 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit II input leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - 0.5 A IOZ OFF-state output current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V - - 0.5 A IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - 0.5 A IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - 0.6 A ICC supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 0.9 A ICC additional supply current VI = VCC  0.6 V; IO = 0 A; VCC = 3.3 V - - 50 A [1] Tamb = 40 C to +125 C VIH VIL VOH VOL HIGH-level input voltage LOW-level input voltage HIGH-level output voltage LOW-level output voltage VCC = 0.8 V 0.75  VCC - - V VCC = 0.9 V to 1.95 V 0.70  VCC - - V VCC = 2.3 V to 2.7 V 1.6 - V V - VCC = 3.0 V to 3.6 V 2.0 - - VCC = 0.8 V - - 0.25  VCC V VCC = 0.9 V to 1.95 V - - 0.30  VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V VI = VIH or VIL IO = 20 A; VCC = 0.8 V to 3.6 V VCC  0.11 - - V IO = 1.1 mA; VCC = 1.1 V 0.6  VCC - - V IO = 1.7 mA; VCC = 1.4 V 0.93 - - V IO = 1.9 mA; VCC = 1.65 V 1.17 - - V IO = 2.3 mA; VCC = 2.3 V 1.77 - - V IO = 3.1 mA; VCC = 2.3 V 1.67 - - V IO = 2.7 mA; VCC = 3.0 V 2.40 - - V IO = 4.0 mA; VCC = 3.0 V 2.30 - - V IO = 20 A; VCC = 0.8 V to 3.6 V - - 0.11 V IO = 1.1 mA; VCC = 1.1 V - - 0.33  VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.41 V IO = 1.9 mA; VCC = 1.65 V - - 0.39 V IO = 2.3 mA; VCC = 2.3 V - - 0.36 V IO = 3.1 mA; VCC = 2.3 V - - 0.50 V IO = 2.7 mA; VCC = 3.0 V - - 0.36 V IO = 4.0 mA; VCC = 3.0 V - - 0.50 V VI = VIH or VIL II input leakage current VI = GND to 3.6 V; VCC = 0 V to 3.6 V - - 0.75 A IOZ OFF-state output current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V - - 0.75 A IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - 0.75 A 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 6 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit IOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V - - 0.75 A ICC supply current VI = GND or VCC; IO = 0 A; VCC = 0.8 V to 3.6 V - - 1.4 A ICC additional supply current VI = VCC  0.6 V; IO = 0 A; VCC = 3.3 V - - 75 A [1] [1] One input at VCC  0.6 V, other input at VCC or GND. 11. Dynamic characteristics Table 8. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7. Symbol Parameter 25 C 40 C to +125 C Min Typ[1] Max Min Max Min Max (85 C) (85 C) (125 C) (125 C) Conditions Unit CL = 5 pF tpd propagation CP to Q; see Figure 5 delay VCC = 0.8 V [2] - 23.6 - - - - - ns VCC = 1.1 V to 1.3 V 2.4 6.3 13.1 2.3 13.3 2.3 13.4 ns VCC = 1.4 V to 1.6 V 2.1 4.3 7.4 1.8 8.0 1.8 8.2 ns VCC = 1.65 V to 1.95 V 1.6 3.4 5.8 1.4 6.4 1.4 6.7 ns VCC = 2.3 V to 2.7 V 1.4 2.5 3.8 1.1 4.3 1.1 4.5 ns 1.2 2.1 3.0 1.0 3.4 1.0 3.6 ns VCC = 3.0 V to 3.6 V ten enable time OE to Q; see Figure 6 [3] VCC = 0.8 V tdis - 21.7 - - - - - ns VCC = 1.1 V to 1.3 V 3.3 5.2 8.1 3.0 9.1 3.0 10.0 ns VCC = 1.4 V to 1.6 V 2.6 4.1 5.6 2.4 6.1 2.4 6.7 ns VCC = 1.65 V to 1.95 V 2.3 3.4 4.6 2.0 5.1 2.0 5.6 ns VCC = 2.3 V to 2.7 V 2.0 2.8 3.7 1.8 4.0 1.8 4.4 ns VCC = 3.0 V to 3.6 V 1.9 2.6 3.4 1.8 3.5 1.8 3.9 ns - 9.8 - - - - - ns disable time OE to Q; see Figure 6 VCC = 0.8 V 74AUP1G374_Q100 Product data sheet [4] VCC = 1.1 V to 1.3 V 2.9 4.5 7.0 2.8 7.2 2.8 7.9 ns VCC = 1.4 V to 1.6 V 2.3 3.3 4.9 2.1 5.1 2.1 5.6 ns VCC = 1.65 V to 1.95 V 2.2 3.2 4.5 2.1 4.7 2.1 5.2 ns VCC = 2.3 V to 2.7 V 1.6 2.3 3.1 1.5 3.4 1.5 3.7 ns VCC = 3.0 V to 3.6 V 1.9 2.6 3.4 1.8 3.6 1.8 4.0 ns All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 7 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7. Symbol Parameter fmax maximum frequency 25 C Conditions 40 C to +125 C Unit Min Typ[1] Max VCC = 0.8 V - 53 - - - - - MHz VCC = 1.1 V to 1.3 V - 203 - 170 - 170 - MHz VCC = 1.4 V to 1.6 V - 347 - 310 - 300 - MHz VCC = 1.65 V to 1.95 V - 435 - 400 - 390 - MHz VCC = 2.3 V to 2.7 V - 550 - 490 - 480 - MHz VCC = 3.0 V to 3.6 V - 619 - 550 - 510 - MHz - 27.1 - - - - - ns VCC = 1.1 V to 1.3 V 2.7 7.2 14.7 2.5 15.0 2.5 15.1 ns VCC = 1.4 V to 1.6 V 2.3 4.9 8.6 2.0 9.1 2.0 9.4 ns VCC = 1.65 V to 1.95 V 2.1 4.0 6.5 1.9 7.0 1.9 7.3 ns VCC = 2.3 V to 2.7 V 1.8 3.1 4.4 1.5 4.9 1.5 5.1 ns 1.6 2.7 3.7 1.3 4.0 1.3 4.2 ns Min Max Min Max (85 C) (85 C) (125 C) (125 C) CP; see Figure 5 CL = 10 pF tpd propagation CP to Q; see Figure 5 delay VCC = 0.8 V [2] VCC = 3.0 V to 3.6 V ten enable time OE to Q; see Figure 6 [3] VCC = 0.8 V tdis - 25.1 - - - - - ns VCC = 1.1 V to 1.3 V 3.8 6.5 10.2 3.5 10.6 3.5 11.7 ns VCC = 1.4 V to 1.6 V 3.1 4.7 6.5 2.7 7.1 2.7 7.8 ns VCC = 1.65 V to 1.95 V 2.7 4.0 5.4 2.5 6.0 2.5 6.6 ns VCC = 2.3 V to 2.7 V 2.4 3.4 4.5 2.2 4.7 2.2 5.2 ns VCC = 3.0 V to 3.6 V 2.3 3.1 4.1 2.1 4.2 2.1 4.6 ns - 11.7 - - - - - ns VCC = 1.1 V to 1.3 V 3.9 5.6 8.3 3.9 8.4 3.9 9.2 ns VCC = 1.4 V to 1.6 V 3.1 4.2 5.8 3.0 6.1 3.0 6.7 ns VCC = 1.65 V to 1.95 V 3.2 4.3 5.7 3.1 5.9 3.1 6.5 ns VCC = 2.3 V to 2.7 V 2.3 3.1 4.0 2.2 4.2 2.2 4.6 ns VCC = 3.0 V to 3.6 V 3.0 3.8 4.8 2.9 5.0 2.9 5.5 ns VCC = 0.8 V - 52 - - - - - MHz VCC = 1.1 V to 1.3 V - 192 - 150 - 150 - MHz disable time OE to Q; see Figure 6 VCC = 0.8 V fmax maximum frequency 74AUP1G374_Q100 Product data sheet [4] CP; see Figure 5 VCC = 1.4 V to 1.6 V - 324 - 280 - 230 - MHz VCC = 1.65 V to 1.95 V - 421 - 310 - 250 - MHz VCC = 2.3 V to 2.7 V - 486 - 370 - 360 - MHz VCC = 3.0 V to 3.6 V - 550 - 410 - 360 - MHz All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 8 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7. Symbol Parameter 25 C Conditions 40 C to +125 C Unit Min Typ[1] Max - 30.6 - - - - - ns VCC = 1.1 V to 1.3 V 3.0 8.0 16.2 2.8 16.5 2.8 16.6 ns VCC = 1.4 V to 1.6 V 2.8 5.5 9.3 2.4 10.1 2.4 10.4 ns VCC = 1.65 V to 1.95 V 2.3 4.5 7.2 2.1 7.9 2.1 8.2 ns VCC = 2.3 V to 2.7 V 2.1 3.5 5.0 1.9 5.5 1.9 5.7 ns 2.0 3.1 4.3 1.7 4.7 1.7 5.0 ns - 28.6 - - - - - ns VCC = 1.1 V to 1.3 V 4.3 7.4 11.6 3.9 12.1 3.9 13.3 ns VCC = 1.4 V to 1.6 V 3.5 5.3 7.2 3.1 8.0 3.1 8.8 ns VCC = 1.65 V to 1.95 V 3.1 4.5 6.1 2.8 6.7 2.8 7.4 ns VCC = 2.3 V to 2.7 V 2.7 3.8 5.0 2.5 5.4 2.5 5.9 ns 2.7 3.6 4.7 2.5 4.9 2.5 5.4 ns Min Max Min Max (85 C) (85 C) (125 C) (125 C) CL = 15 pF tpd propagation CP to Q; see Figure 5 delay VCC = 0.8 V [2] VCC = 3.0 V to 3.6 V ten enable time OE to Q; see Figure 6 [3] VCC = 0.8 V VCC = 3.0 V to 3.6 V tdis disable time OE to Q; see Figure 6 [4] VCC = 0.8 V fmax maximum frequency - 13.5 - - - - - ns VCC = 1.1 V to 1.3 V 5.0 6.8 9.5 4.9 9.6 4.9 10.6 ns VCC = 1.4 V to 1.6 V 3.9 5.1 6.8 3.8 7.0 3.8 7.7 ns VCC = 1.65 V to 1.95 V 4.3 5.4 7.0 4.1 7.2 4.1 7.9 ns VCC = 2.3 V to 2.7 V 3.0 3.9 4.9 2.9 5.1 2.9 5.6 ns VCC = 3.0 V to 3.6 V 4.1 5.1 6.2 4.0 6.4 4.0 7.0 ns VCC = 0.8 V - 50 - - - - - MHz VCC = 1.1 V to 1.3 V - 181 - 120 - 120 - MHz VCC = 1.4 V to 1.6 V - 301 - 190 - 160 - MHz VCC = 1.65 V to 1.95 V - 407 - 240 - 190 - MHz VCC = 2.3 V to 2.7 V - 422 - 300 - 270 - MHz VCC = 3.0 V to 3.6 V - 481 - 320 - 300 - MHz - 40.8 - - - - - ns CP; see Figure 5 CL = 30 pF tpd propagation CP to Q; see Figure 5 delay VCC = 0.8 V 74AUP1G374_Q100 Product data sheet [2] VCC = 1.1 V to 1.3 V 3.7 10.3 20.5 3.5 21.2 3.5 21.6 ns VCC = 1.4 V to 1.6 V 3.3 7.0 11.6 3.2 12.6 3.2 13.3 ns VCC = 1.65 V to 1.95 V 3.2 5.8 9.1 2.9 9.8 2.9 10.4 ns VCC = 2.3 V to 2.7 V 3.0 4.7 6.5 2.6 7.0 2.6 7.4 ns VCC = 3.0 V to 3.6 V 2.9 4.2 5.8 2.5 6.6 2.5 6.9 ns All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 9 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7. Symbol Parameter ten 25 C Conditions Max - 39.0 - - - - - ns VCC = 1.1 V to 1.3 V 5.6 9.8 15.7 5.0 16.5 5.0 18.2 ns VCC = 1.4 V to 1.6 V 4.6 7.0 9.5 4.1 10.6 4.1 11.7 ns VCC = 1.65 V to 1.95 V 4.1 5.9 7.9 3.7 8.6 3.7 9.5 ns VCC = 2.3 V to 2.7 V 3.7 5.0 6.6 3.3 7.1 3.3 7.8 ns 3.5 4.8 6.2 3.2 6.5 3.2 7.2 ns enable time OE to Q; see Figure 6 disable time OE to Q; see Figure 6 VCC = 0.8 V maximum frequency Min Max Min Max (85 C) (85 C) (125 C) (125 C) [3] VCC = 3.0 V to 3.6 V fmax Unit Min VCC = 0.8 V tdis 40 C to +125 C Typ[1] [4] - 19.0 - - - - - ns VCC = 1.1 V to 1.3 V 8.1 10.2 13.3 8.0 13.5 8.0 14.9 ns VCC = 1.4 V to 1.6 V 6.4 7.8 9.7 6.3 10.0 6.3 11.0 ns VCC = 1.65 V to 1.95 V 7.4 8.8 10.7 7.2 10.9 7.2 12.0 ns VCC = 2.3 V to 2.7 V 5.2 6.3 7.5 5.1 7.8 5.1 8.6 ns VCC = 3.0 V to 3.6 V 7.5 8.8 10.3 7.4 10.5 7.4 11.6 ns VCC = 0.8 V - 28 - - - - - VCC = 1.1 V to 1.3 V - 128 - 70 - 70 - MHz VCC = 1.4 V to 1.6 V - 206 - 120 - 110 - MHz VCC = 1.65 V to 1.95 V - 262 - 150 - 120 - MHz VCC = 2.3 V to 2.7 V - 269 - 190 - 170 - MHz VCC = 3.0 V to 3.6 V - 309 - 200 - 190 - MHz VCC = 0.8 V - 5.1 - - - - - ns VCC = 1.1 V to 1.3 V - 1.5 - 3.2 - 3.5 - ns VCC = 1.4 V to 1.6 V - 0.9 - 1.5 - 1.7 - ns VCC = 1.65 V to 1.95 V - 0.7 - 1.0 - 1.1 - ns VCC = 2.3 V to 2.7 V - 0.5 - 0.8 - 0.8 - ns VCC = 3.0 V to 3.6 V - 0.5 - 0.7 - 0.8 - ns VCC = 0.8 V - 2.1 - - - - - ns CP; see Figure 5 MHz CL = 5 pF, 10 pF, 15 pF and 30 pF tW tsu(H) pulse width set-up time HIGH 74AUP1G374_Q100 Product data sheet CP; HIGH or LOW; see Figure 5 D to CP; see Figure 5 VCC = 1.1 V to 1.3 V - 0.5 - 1.4 - 1.4 - ns VCC = 1.4 V to 1.6 V - 0.3 - 1.0 - 1.0 - ns VCC = 1.65 V to 1.95 V - 0.3 - 0.9 - 0.9 - ns VCC = 2.3 V to 2.7 V - 0.3 - 0.7 - 0.7 - ns VCC = 3.0 V to 3.6 V - 0.2 - 0.6 - 0.6 - ns All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 10 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7. Symbol Parameter tsu(L) th CPD set-up time LOW hold time 25 C Conditions Unit Min Max VCC = 0.8 V - 3.5 - - - - - ns VCC = 1.1 V to 1.3 V - 0.8 - 1.8 - 1.8 - ns VCC = 1.4 V to 1.6 V - 0.6 - 1.2 - 1.2 - ns Min Max Min Max (85 C) (85 C) (125 C) (125 C) D to CP; see Figure 5 VCC = 1.65 V to 1.95 V - 0.5 - 1.1 - 1.1 - ns VCC = 2.3 V to 2.7 V - 0.4 - 1.0 - 1.0 - ns VCC = 3.0 V to 3.6 V - 0.5 - 1.0 - 1.0 - ns D to CP; see Figure 5 VCC = 0.8 V - 2.8 - - - - - ns VCC = 1.1 V to 1.3 V - 0.7 - 0 - 0 - ns VCC = 1.4 V to 1.6 V - 0.4 - 0 - 0 - ns VCC = 1.65 V to 1.95 V - 0.4 - 0 - 0 - ns VCC = 2.3 V to 2.7 V - 0.3 - 0 - 0 - ns VCC = 3.0 V to 3.6 V - 0.4 - 0 - 0 - ns - 1.7 - - - - - pF VCC = 1.1 V to 1.3 V - 1.8 - - - - - pF VCC = 1.4 V to 1.6 V - 1.8 - - - - - pF VCC = 1.65 V to 1.95 V - 2.0 - - - - - pF VCC = 2.3 V to 2.7 V - 2.3 - - - - - pF VCC = 3.0 V to 3.6 V - 2.8 - - - - - pF power VI = GND to VCC; dissipation f = 1 MHz; output enabled i capacitance VCC = 0.8 V [1] All typical values are measured at nominal VCC. [2] tpd is the same as tPLH and tPHL. [3] ten is the same as tPZH and tPZL. [4] tdis is the same as tPHZ and tPLZ. [5] 40 C to +125 C Typ[1] [5] CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD  VCC2  fi  N + (CL  VCC2  fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; (CL  VCC2  fo) = sum of the outputs; N = number of inputs switching. 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 11 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 12. Waveforms VI VM D input GND th th t su(H) t su(L) 1/fclk VI CP input VM GND tW t PHL t PLH VOH VM Q output VOL 001aad498 Measurement points are given in Table 9. The shaded areas indicate when the input is permitted to change for predictable output performance. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Fig 5. Clock propagation delays, pulse width, set-up times, hold times and maximum frequency (CP) Table 9. Measurement points Supply voltage Input Output VCC VM VI tr = tf VM VX VY 0.8 V to 1.6 V 0.5  VCC VCC  3.0 ns 0.5  VCC VOL + 0.1 V VOH  0.1 V 1.65 V to 2.7 V 0.5  VCC VCC  3.0 ns 0.5  VCC VOL + 0.15 V VOH  0.15 V 3.0 V to 3.6 V 0.5  VCC VCC  3.0 ns 0.5  VCC VOL + 0.3 V VOH  0.3 V 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 12 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state VI OE input VM GND tPLZ tPZL VCC output LOW-to-OFF OFF-to-LOW VM VX VOL tPHZ tPZH VOH VY output HIGH-to-OFF OFF-to-HIGH VM GND outputs enabled outputs enabled outputs disabled mna644 Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Fig 6. Enable and disable times VCC VEXT 5 kΩ G VI VO DUT RT CL RL 001aac521 Test data is given in Table 10. Definitions for test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Fig 7. Test circuit for measuring switching times Table 10. Test data Supply voltage Load VEXT VCC CL 0.8 V to 3.6 V 5 pF, 10 pF, 15 pF and 30 pF 5 k or 1 M [1] RL [1] tPLH, tPHL tPZH, tPHZ tPZL, tPLZ open GND 2  VCC For measuring enable and disable times, RL = 5 k. For measuring propagation delays, set-up and hold times and pulse width, RL = 1 M.. 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 13 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 13. Package outline Plastic surface-mounted package; 6 leads SOT363 D E B y X A HE 6 5 v M A 4 Q pin 1 index A A1 1 2 e1 3 c bp Lp w M B e detail X 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A1 max bp c D E e e1 HE Lp Q v w y mm 1.1 0.8 0.1 0.30 0.20 0.25 0.10 2.2 1.8 1.35 1.15 1.3 0.65 2.2 2.0 0.45 0.15 0.25 0.15 0.2 0.2 0.1 OUTLINE VERSION REFERENCES IEC JEDEC SOT363 Fig 8. JEITA EUROPEAN PROJECTION ISSUE DATE 04-11-08 06-03-16 SC-88 Package outline SOT363 (SC-88) 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 14 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 14. Abbreviations Table 11. Abbreviations Acronym Description CDM Charged Device Model DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model MIL Military 15. Revision history Table 12. Revision history Document ID Release date Data sheet status Change notice Supersedes 74AUP1G374_Q100 v.1 20130219 Product data sheet - - 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 15 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nexperia.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet. 16.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. 74AUP1G374_Q100 Product data sheet Suitability for use in automotive applications — This Nexperia product has been qualified for use in automotive applications. Unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of a Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer. All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 16 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com 74AUP1G374_Q100 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 19 February 2013 © Nexperia B.V. 2017. All rights reserved 17 of 18 74AUP1G374-Q100 Nexperia Low-power D-type flip-flop; positive-edge trigger; 3-state 18. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 12 13 14 15 16 16.1 16.2 16.3 16.4 17 18 © General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 4 Dynamic characteristics . . . . . . . . . . . . . . . . . . 7 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 Legal information. . . . . . . . . . . . . . . . . . . . . . . 16 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 16 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Contact information. . . . . . . . . . . . . . . . . . . . . 17 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Nexperia B.V. 2017. All rights reserved For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: 19 February 2013