74LVT14D

INTEGRATED CIRCUITS 74LVT14 3.3V Hex inverter Schmitt trigger Product specification IC24 Data Handbook
     1996 Aug 28 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 DESCRIPTION FUNCTION TABLE The 74LVT14 is a high-performance BiCMOS product designed for VCC operation at 3.3V. They are capable of transforming slowly changing input signals into sharply defined, jitter free output signals. In addition, they have greater noise margin than conventional inverters. Each circuit contains a Schmitt trigger followed by a Darlington level shifter and a phase splitter driving a TTL totem-pole output. The Schmitt trigger uses positive feedback to effectively speed-up slow input transitions, and provide different input threshold voltages for positive-going and negative-going input threshold (typically 600mV) is determined internally by resistor ratios and is insensitive to temperature and supply voltage variations. INPUTS OUTPUT Dn Qn L H H L NOTES: H = High voltage level L = Low voltage level LOGIC DIAGRAM QUICK REFERENCE DATA SYMBOL CONDITIONS Tamb = 25°C; GND = 0V PARAMETER Propagation delay An to Yn tPLH tPHL A0 A1 TYPICAL CL = 50pF; VCC = 3.3V UNIT A2 A3 3.2 3.0 CIN Input capacitance VI = 0V or 3.0V ICCL Total supply current Outputs low; VCC = 3.6V ns A4 3 VCC = Pin 14 GND = Pin 7 pF A5 1 2 3 4 5 6 9 8 11 10 13 12 Y0 Y1 Y2 Y3 Y4 Y5 SV00087 1.5 mA IEC/IEEE SYMBOL PIN CONFIGURATION 1 A0 1 14 VCC Y0 2 13 A5 A1 3 12 Y5 Y1 4 11 A4 A2 5 10 Y4 Y2 6 9 A3 GND 7 8 Y3 SA00338 1 2 3 4 5 6 9 8 11 10 13 12 PIN DESCRIPTION SF00031 PIN NUMBER SYMBOL 1, 3, 5, 9, 11, 13 An Data inputs 2, 4, 6, 8, 10, 12 Yn Data outputs 7 GND Ground (0V) 14 VCC Positive supply voltage NAME AND FUNCTION ORDERING INFORMATION TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA DWG NUMBER 14-Pin Plastic SO PACKAGES –40°C to +85°C 74LVT14 D 74LVT14 D SOT108-1 14-Pin Plastic SSOP –40°C to +85°C 74LVT14 DB 74LVT14 DB SOT337-1 14-Pin Plastic TSSOP –40°C to +85°C 74LVT14 PW 74LVT14 PWDH SOT402-1 1996 Aug 28 2 853-1870 17244 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 LOGIC SYMBOL 1 3 5 9 11 13 A0 A1 A2 A3 A4 A5 Y0 Y1 Y2 Y3 Y4 Y5 VCC = Pin 14 GND = Pin 7 2 4 6 8 10 12 SV00088 ABSOLUTE MAXIMUM RATINGS1, 2 SYMBOL VCC IIK PARAMETER RATING UNIT –0.5 to +4.6 V –50 mA –0.5 to +7.0 V VO < 0 –50 mA Output in Off or High state –0.5 to +7.0 V Output in High state –32 Output in Low state 64 DC supply voltage DC input diode current VI < 0 voltage3 VI DC input IOK DC output diode current VOUT CONDITIONS DC output voltage3 IOUT DC output current Tstg Storage temperature range mA °C –65 to 150 NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C. 3. The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed. RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL VCC PARAMETER UNIT DC supply voltage MIN MAX 2.7 3.6 V 0 5.5 V VI Input voltage VIH High-level input voltage VIL Low-level Input voltage 0.8 V IOH High-level output current –20 mA IOL Low-level output current 32 mA ∆t/∆v Input transition rise or fall rate; Outputs enabled 10 ns/V Tamb Operating free-air temperature range +85 °C 1996 Aug 28 2.0 –40 3 V Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 DC ELECTRICAL CHARACTERISTICS Over recommended operating conditions Voltages are referenced to GND (ground = 0V) LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C MIN TYP1 MAX UNIT VT+ Positive-going threshold VCC = 3.3V 1.5 1.7 2.0 V VT– Negative-going threshold VCC = 3.3V 0.9 1.1 1.3 V ∆VT Hysteresis VCC = 3.3V 0.4 0.6 VIK Input clamp voltage VCC = 2.7V; IIK = –18mA –1.2 VCC = 2.7 to 3.6V; IOH = –100µA VOH High-level output voltage VOL Low–level output voltage II Input leakage current IOFF Output off current ICCH Quiescent supply current ∆ICC CI V VCC–0.2 VCC = 2.7V; IOH = –6mA 2.4 VCC = 3.0V; IOH = –20mA 2.0 V VCC = 2.7V; IOL = 100µA 0.2 VCC = 2.7V; IOL = 24mA 0.5 VCC = 3.0V; IOL = 32mA 0.5 VCC = 0 or 3.6V; VI = 5.5V 10 VCC = 3.6V; VI = VCC or GND ±1 VCC = 0V; VI or VO = 0 to 4.5V ±100 VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0 0.02 V µA µA mA VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0 ICCL V Additional supply current per input pin2 VCC = 3V to 3.6V; One input at VCC–0.6V, Other inputs at VCC or GND Input capacitance VI = 3V or 0 1.5 3 µA 0.2 3 pF NOTES: 1. All typical values are at VCC = 3.3V and Tamb = 25°C. 2. This is the increase in supply current for each input at the specificed voltage level other than VCC or GND AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL tPLH tPHL TEST CONDITION PARAMETER Propagation delay An to Yn VCC = 3.3V ±0.3V Waveform 1 AC WAVEFORMS VM = 1.5V, VIN = GND to 2.7V An VM VM tPHL Yn VM tPLH VM SA00341 Waveform 1. Propagation delay for inverting outputs 1996 Aug 28 4 VCC = 2.7V MIN TYP MAX MAX 1.0 1.0 3.8 3.2 5.7 4.5 6.9 4.1 UNIT ns Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 TEST CIRCUIT AND WAVEFORMS VCC 10% 0V tTHL (tF) D.U.T. RT CL AMP (V) VM 10% VOUT PULSE GENERATOR 90% VM NEGATIVE PULSE VIN tW 90% tTLH (tR) tTLH (tR) RL tTHL (tF) 90% POSITIVE PULSE Test Circuit for Outputs AMP (V) 90% VM VM 10% 10% tW 0V VM = 1.5V Input Pulse Definition INPUT PULSE REQUIREMENTS DEFINITIONS FAMILY RL = Load resistor; see AC CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC CHARACTERISTICS for value. 74LVT RT = Termination resistance should be equal to ZOUT of pulse generators. 1996 Aug 28 Amplitude Rep. Rate 2.7V ≤10MHz tW tR tF 500ns ≤2.5ns ≤2.5ns SV00022 5 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 SO14: plastic small outline package; 14 leads; body width 3.9 mm 1996 Aug 28 6 SOT108-1 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm 1996 Aug 28 7 SOT337-1 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm 1996 Aug 28 8 SOT402-1 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 NOTES 1996 Aug 28 9 Philips Semiconductors Product specification 3.3V Hex inverter Schmitt trigger 74LVT14 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Formative or in Design This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. Preliminary Specification Preproduction Product This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product Specification Full Production This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act.  Copyright Philips Electronics North America Corporation 1996 All rights reserved. Printed in U.S.A.