S1D2504A01-D0B0

JULY. 2000 DATA SHEET S1D2504A01 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER 24-DIP-300 The S1D2504A01 is very high frequency video amplifier system with I2C BUS control used in Monitors. It contains 3 matched R/G/B video Amplifiers and provides flexible interfacing to the I2C BUS controlled adjustment systems. FUNCTIONS • • • • • • • • • R/G/B Video Amplifier I2C BUS Control Contrast Control Brightness Control Cut-Off Brightness Control R/G/B SUB Contrast/Cut Off Control Blank/Clamp Gate Auto beam current limitation (ABL) is possible with external pin. The S1D2504A01 includes white balance adjustment that is effective on brightness (by Cut-Off control for each channel). ORDERING INFORMATION Device S1D2504A01-D0B0 Package 24-DIP-300 Operating Temperature -20 °C — 75 C ° FEATURES • • 3-Channel matched R/G/B Video Amplifiers I2C BUS control items – Contrast control for the 3 channels – Brightness control for the 3 channels – SUB Contrast control for each channel – Cut-Off control for each channel – Cut-Off Brightness control for the 3 channels – Switch Registers for SBLK and Cut-Off Offset Current Built-in ABL (Automatic Beam Limitation) Built-in Video output Brightness clamp 3-Channel R/G/B Video Amplifier 85 MHz @f-3 dB Contrast Control Range: -38 dB SUB Contrast Control Range: -11 dB Capable of 7 Vpp Output Swing • • • • • • 1 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER BLOCK DIAGRAM ONE (RED) OF THREE CHANNELS BLK VCC1 RIN 1 A2 23 VIDEO CONTRAST SUB CONTRAST ROUT RCLP 2 3 4 2.4V A1 A3 CLP 24 16 21 GND1 GIN gm2 + CT OFFSET BLK CLP + CUT OFF GND2 BIN VCC2 5 6 7 GND(L) 9 CONTRAST (00H) B DRIVE (04H) G DRIVE (03H) R DRIVE (02H) ABL 8 CLAMP GATE SCL SDA 10 11 I2C BUS CONTROL BLANK GATE SOFT BLANK D7 (01H) CONTROL 2 _ RCT GOUT + 22 15 GCLP GCT BOUT CT BRT 18 17 BCLP BCT VCC3 CUT OFF OFFSET D6:5 (01H) 14 20 19 CUT OFF BRIGHT (05H) BRIGHTNESS (01H) G CUT OFF (07H) R CUT OFF (06H) B CUT OFF (08H) GND3 12 CLP 13 BLK I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 PIN CONFIGURATION 1 VCC1 RCLP 24 2 RIN ROUT 23 3 GND1 GCLP 22 4 GIN GOUT 21 5 KA2504 GND2 VCC3 20 6 BIN S1D2504A01 GND3 19 7 VCC2 BOUT 18 8 ABL BCLP 17 9 GND(L) RCT 16 10 SCL GCT 15 11 SDA BCT 14 12 CLP BLK 13 Table 1. Pin Configuration NO 1 2 3 4 5 6 7 8 9 10 11 12 Symbol VCC1 RIN GND1 GIN GND2 BIN VCC2 ABL GND (L) SCL SDA CLP I/O I I I I I/O I/O I Configuration Normal Power Supply Red Video Input Normal Ground Green Video Input Normal Ground Blue Video Input Normal Power Supply Automatic Beam Limit Logic Ground Serial Clock Serial Data Clamp Gate Input NO 13 14 15 16 17 18 19 20 21 22 23 24 Symbol BLK BCT GCT RCT BCLP BOUT GND3 VCC3 GOUT GCLP ROUT RCLP I/O I I I I O O O Configuration Blank Gate Input Blue Cut off ctrl Green Cut off ctrl Red Cut off ctrl Blue Clamp Cap Blue Video Output Drive Power Ground Drive Power Supply Green Video Output Green Clamp Cap Red Video Output Red Clamp Cap 3 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER PIN DESCRIPTION Table 2. Pin Description Pin No 1 2 Pin Name VCC1 Red Video Input (RIN) 2.4V Schematic VCC Description Normal VCC 4 Green Video Input (GIN) Video Input (Maximum 0.7 Vpp) PIN 2 8 Blue Video Input (BIN) 3 5 7 8 GND1 GND2 VCC2 VCC Normal Ground Normal Ground Logic VCC ABL PIN 8 Auto Beam Limitation (Control Range: 0.5 ~ 4.5 V ) 9 GND (L) - Logic Ground 4 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 Table 2. Pin Description (Continued) Pin No 10 Pin Name Serial Clock Input (SCL) Schematic Description 3.2V 11 Serial Data Input (SDA) PIN 10 SCL, SDA for I2C Bus Control 5.1V VCC 12 Clamp Gate Input (CLP) Clamp Gate Input: TTL Level Active Low Clamp Gate Min. Duty PIN12 f: 34 kHz duty: 0.3 µS 7V VCC 13 Blank Gate Input (BLK) PIN13 Blank Gate Input: TTL Level Active Low 14 Blue Cut-Off (BCT) vcc vcc 15 Green Cut-Off (GCT) Cut-Off Control Output Icut-off = Ict+Ictbrt+Ics 1+Ics 2 Ict : 0 ~ 540µA pin 14 lctbrt lct Ictbrt: 0 ~ 160µA Ics 1 : 80µA Ics 2 : 160µA CS2 CS1 16 Red Cut-Off (RCT) 5 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER Table 2. Pin Description (Continued) Pin No 17 Pin Name Blue Clamp Cap (BCLP) Bright Vout Schematic + PIN 17 Description - 22 Green Clamp Cap (GCLP) Clamp Cap for Brightness (During Clamp Gate Low) 24 Red Clamp Cap (RCLP) 18 Blue Video Output (BOUT) vcc 21 Green Video Output (GOUT) PIN 18 Video Out 23 Red Video Output (ROUT) GND3 VCC3 - 663uA 19 20 Normal Ground Drive VCC 6 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 ABSOLUTE MAXIMUM RATINGS NO 1 2 Item Normal, Logic, Driver Power Supply Maximum Power Dissipation Symbol VCC 1, 2, 3 PDmax Value 13.2 1.5 Unit V W THERMAL CHARACTERISTICS NO 1 2 3 4 Storage Temperature Operating Temperature Thermal Resistance (Junction ambient) Junction Temperature Item Symbol Tstg Topr θja Tj Value -65 — 150 -20 — 75 60.0 150.0 Unit °C °C °C/W °C ESD PARAMETER NO 1 2 3 Human Body Model (C = 100pF, R = 1.5k Ω) Machine Model (C = 200pF, R = 0) Charge Device Model Item Symbol HBM MM CDM Value 2000 300 800 Unit V V V I2C BUS ELECTRICAL CHARACTERISTICS Symbol VinH VinL IinH IinL fSCL Description High Level Input Voltage Low Level Input Voltage High Level Input Current Low Level Input Current SCL Clock frequency Min 3.0 Typ Max 1.5 1.0 -10 200 Unit V V µA µA kHz 7 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER ELECTRICAL CHARACTERISTICS DC Electrical Characteristics (Tamb = 25 °C, VCC = 12 V, VDD = 12 V) Table 3. DC Electrical Characteristics No Parameter Symbol Min 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Supply Current Maxium Supply Curent R Input Bias Voltage G Input Bias Voltage B Input Bias Voltage R Clamp Gate Low Input Voltage G Clamp Gate Low Input Voltage B Clamp Gate Low Input Voltage R Clamp Gate High Input Voltage G Clmap Gate High Input Voltage B Clamp Gate High Input Voltage Clamp Gate Low Input Current Clamp Gate High Input Current R Output Clamp Cap Charge Current G Output Clamp Cap Charge Current B Output Clamp Cap Charge Current R Output Clamp Cap Discharge Current G Output Clamp Cap Discharge Current B Output Clamp Cap Discharge Current R Blank Gate Low Input Voltage G Blank Gate Low Input Voltage B Blank Gate Low Input Voltage R Blank Gate High Input Voltage G Blank Gate High Input Voltage B Blank Gate High Input Voltage Blank Gate Low Input Current Blank Gate High Input Current ICC ICC max VRb VGb VBb V12LR V12LG V12LB V12HR V12HG V12HB I12L I12H IclampR+ IclampG+ IclampB+ IclampRIclampGIclampBV13LR V13LG V13LB V13HR V13HG V13HB I13L I13H 60 70 2.2 2.2 2.2 0.8 0.8 0.8 -5.0 0.45 0.45 0.45 -1.50 -1.50 -1.50 0.8 0.8 0.8 -5.0 Value Typ 80 90 2.4 2.4 2.4 1.5 1.5 1.5 1.5 1.5 1.5 -2.0 0.01 0.75 0.75 0.75 -0.75 -0.75 -0.75 1.5 1.5 1.5 1.5 1.5 1.5 -2.0 0.01 Max 100 110 2.6 2.6 2.6 2.0 2.0 2.0 1.0 1.50 1.50 1.50 -0.45 -0.45 -0.45 2.0 2.0 2.0 1.0 mA mA V V V V V V V V V µA µA mA mA mA mA mA mA V V V V V V µA µA Unit 8 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 Table 3. DC Electrical Characteristics (Continued) No Parameter Symbol Min 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 R BRT LOW Output Voltage (POR) G BRT Low Output Voltage (POR) B BRT Low Output Voltage (POR) R-G Black Level Output Voltage G-B Black Level Output Voltage B-R Black Level Output Voltage R Output High Voltage G Output High Voltage B Output High Voltage R Blank Output Voltage G Blank Output Voltage B Blank Output Voltage SCL High Input Current SDA High Input Current SCL/SDA Low Level Input Voltage SCL/SDA High Level Input Voltage R Input Resistance G Input Resistance B Input Resistance R Spot Killer Voltage G Spot Killer Voltage B Spot Killer Voltage R Center Ext. Cut -Off Output Current G Center Ext. Cut -Off Output Current B Center Ext. Cut -Off Output Current R Cut -Off Output Current Range G Cut -Off Output Current Range B Cut -Off Output Current Range R Cut -Off BRT Output Current Range G Cut -Off BRT Output Current Range B Cut-Off BRT Output Current Range R Ext. Cut-Off Offset Output Current1 VOporR VOporG VOporB ∆R-GBL ∆G-BBL ∆B-RBL VOHR VOHG VOHB VOBR VOBG VOBB I10H I11H VbusL VbusH Rin Gin Bin VspotR VspotG VspotB IctX_80R Ictx_80G Ictx_80B ∆IctxR ∆IctxG ∆IctxB ∆IctbrtR ∆IctbrtG ∆IctbrtB Ics1R 0.8 0.8 0.8 6.2 6.2 6.2 3 9.2 9.2 9.2 220 220 220 440 440 440 150 150 150 70 Value Typ 1.0 1.0 1.0 0.0 0.0 0.0 7.5 7.5 7.5 0.1 0.1 0.1 0.01 0.01 10 10 10 10.4 10.4 10.4 270 270 270 540 540 540 170 170 170 85 Max 1.2 1.2 1.2 ∆0.2 ∆0.2 ∆0.2 9.0 9.0 9.0 0.2 0.2 0.2 1.0 1.0 1.5 11.2 11.2 11.2 320 320 320 640 640 640 210 210 210 100 V V V V V V V V V V V V µA µA V V kΩ kΩ kΩ V V V µA µA µA µA µA µA µA µA µA µA Unit 9 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER Table 3. DC Electrical Characteristics (Continued) No Parameter Symbol Min 60 61 62 63 64 65 66 67 68 69 70 G Ext. Cut-Off Offset Output Current1 B Ext.Cut-Off Offset Output Current1 R Ext.Cut-Off Offset Output Current2 G Ext.Cut-Off Offset Output Current2 B Ext.Cut-Off Offset Output Current2 R Soft Blank Output Voltage G Soft Blank Output Voltage B Soft Blank Output Voltage R Brightness High Output Voltage G Brightness High Output Voltage B Brightness High Output Voltage Ics1G Ics1B Ics2R Ics2G Ics2B VOsoftR VOsoftG VOsoftB VOHR VOHG VOHB 70 70 140 140 140 2.5 2.5 2.5 Value Typ 85 85 160 160 160 0.1 0.1 0.1 3.0 3.0 3.0 Max 100 100 180 180 180 0.2 0.2 0.2 3.5 3.5 3.5 µA µA µA µA µA V V V V V V Unit Current (uA) 940uA Cut-off Control Offset Total Current (0uA¡-940uA) R,G,B,Cut-off Control Current (0uA¡-540uA) Cut-off Bright Control Current (0uA¡-160uA) 540 240 160 80 CS1/2 On CS1 On Cut-off Control Offset Current (0uA¡-240uA) (Cut-off Control Offset Current & Sink Current Waveform) 10 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 AC Electrical Characteristics (Tamb = 25°C, V CC = 12 V, VDD = 12 V) Table 4. AC Electrical Characteristics No Parameter Symbol Min 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 R Video Bandwidth G Video Bandwidth B Video Bandwidth R Video Amp Gain G Video Amp Gain B Video Amp Gain Max Gain Difference between R-G AMP Max Gain Difference between G-B AMP Max Gain Difference between B-R AMP Low Gain Difference between R-G AMP Low Gain Difference between G-B AMP Low Gain Difference between B-R AMP R Sub Drive Ctrl Max. -Center G Sub Drive Ctrl Max. -Center B Sub Drive Ctrl Max. -Center R Sub Drive Ctrl Min. -Center G Sub Drive Ctrl Min. -Center B Sub Drive Ctrl Min. -Center R Contrast Ctrl Max. -Center G Contrast Ctrl Max. -Center B Contrast Ctrl Max. -Center R Contrast Ctrl Min. -Center G Contrast Ctrl Min. -Center B Contrast Ctrl Min. -Center R ABL Control Range G ABL Control Range B ABL Control Range R Video Amp THD G Video Amp THD f-3dBR f-3dBG f-3dBB AvmaxR AvmaxG AvmaxB ∆AvmaxRG ∆AvmaxGB ∆AvmaxBR ∆AvlowRG ∆AvlowGB ∆AvlowBR AvDRmax AvDGmax AvDBmax AvDRmin AvDGmin AvDBmin AvCRmax AvCGmax AvCBmax AvCRmin AvCGmin AvCBmin ∆ABLR ∆ABLG ∆ABLB THDR THDG 85 85 85 15.5 15.5 15.5 -1.0 -1.0 -1.0 -1.0 -1.0 -1.0 -3 -3 -3 -11 -11 -11 -7 -7 -7 -8.5 -8.5 -8.5 Value Typ 17.5 17.5 17.5 -4 -4 -4 -8 -8 -8 -6 -6 -6 -11.5 -11.5 -11.5 1.0 1.0 Max 19.5 19.5 19.5 1.0 1.0 1.0 1.0 1.0 1.0 -5 -5 -5 -5 -5 -5 -4 -4 -4 -35 -35 -35 -14.5 -14.5 -14.5 5.0 5.0 MHz MHz MHz dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB % % Unit 11 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER Table 4. AC Electrical Characteristics (Continued) No Parameter Symbol Min 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 B Video Amp THD R Video Rising Time G Video Rising Time B Video Rising Time R Video Falling Time G Video Falling Time B Video Falling Time R Blank Output Rising Time G Blank Output Rising Time B Blank Output Rising Time R Blank Output Falling Time G Blank Output Falling Time B Blank Output Falling Time R Blank Rising Prop. Delay G Blank Rising Prop. Delay B Blank Rising Prop. Delay R Blank Falling Prop. Delay G Blank Falling Prop. Delay B Blank Falling Prop. Delay R Video Amp ISO1 10 kHz R Video Amp ISO2 10 kHz G Video Amp ISO1 10 kHz G Video Amp ISO2 10 kHz B Video Amp ISO1 10 kHz B Video Amp ISO2 10 kHz R Video Amp ISO1 10 MHz R Video Amp ISO2 10 MHz G Video Amp ISO1 10 MHz G Video Amp ISO2 10 MHz B Video Amp ISO1 10 MHz B Video Amp ISO2 10 MHz THDB trR trG trB tfR tfG tfB trBlankR trBlankG trBlankB tfBlankR tfBlankG tfBlankB trBlankPrR trBlankPrG trBlankPrB tfBlankPrR tfBlankPrG tfBlankPrB ISO1_10KR ISO2_10KG ISO1_10KB ISO2_10KR ISO1_10KG ISO2_10KB ISO1_10MR ISO2_10MR ISO1_10MG ISO2_10MG ISO1_10MB ISO2_10MB Value Typ 1.0 4.0 4.0 4.0 4.0 4.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 23 23 23 20 20 20 -65 -65 -65 -65 -65 -65 -50 -50 -50 -50 -50 -50 Max 5.0 5.0 5.0 5.0 5.0 5.0 5.0 15.0 15.0 15.0 15.0 15.0 15.0 50 50 50 45 45 45 -45 -45 -45 -45 -45 -45 -35 -35 -35 -35 -35 -35 % nS nS nS nS nS nS nS nS nS nS nS nS nS nS nS nS nS nS dB dB dB dB dB dB dB dB dB dB dB dB Unit 12 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 FUNCTIONAL DESCRIPTION I2C BUS Recommended Operating Conditions Table 5. I 2C BUS Recommended Operating Conditions Symbol VinH VinL fSCL tBUF tHDS tSUP tLOW tHIGH tHDAT tSUPDAT tR tF Description Input High Level Voltage Input Low Level Voltage SCL Clock frequency Hold time before a new transmission can start Hold time for Start conditions Set-Up time for Stop conditions The Low Period of SCL The High Period of SCL Hold time data Set-Up time data Rise time of SCL Fall time of SCL Min 3.0 0 1.3 0.6 0.6 1.3 0.6 0.3 0.25 Typ Max 5.0 1.5 200 1.0 3.0 Unit V V kHz uS uS uS uS uS uS uS uS uS I2C BUS Timing Requirement Stop:Clock High Start:Clock High tBUF tHDAT SDA tHDS SCL tLOW Data Change:Clock Low tHIGH tSUPDAT tSUP Figure 1. I2C BUS Timing Requirement Register Description 1. Contrast Adjustment (8-Bits) The Contrast adustment is made by controlling simultaneously the gain of three internal variable gain amplifiers through the I2C bus interface. The Contrast adjustment allows you to cover a typical range of 38 dB. 2. Sub Contrast Adjustments (8-Bits × 3) These Adustments are used to adjust the gain of each channel controlled by the I2C bus. The Sub Contrast adjustment allows you to cover a typical range of 12 dB. 13 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER 3. Brightness Adjustment (5-Bits) The Brightness adjustment controls to add the same black level (pedestal) to the 3-channel R/G/B signals by I2C bus. 4. Cut-Off Adjustments (8-Bits × 3) These Adjustments are used to adjust the white balance of the each channel controlled by the I2C bus. 5. Cut-Off Brightness Adjustment (8-Bits) The Cut-Off Brightness Adjustment controls the 3-channel Cut-Off by I2C bus. 6. Slave Address The 2-wire serial interface is an I2C BUS interface. The Slave address of the S1D2504A01 is DCH (hexadecimal) Bit 8 1 Bit 7 1 Bit 6 0 Bit 5 1 Bit 4 1 Bit 3 1 Bit 2 0 Bit 1 0 (W) 7. Data Transfer All Bytes are sent MSB (Most Significant Bit) bit first and the write data transfer is closed by a STOP. The MCU can write data into the S1D2504A01 registers. To write data into the S1D2504A01, after a start, MCU must send : - The I2C address slave byte with a low level for R/W bit (bit 1) - The byte of the internal register address where the MCU wants to write data. (SUB Address) - The Data sent to slave - Stop - 1-Byte Data Transfer STA Slave ADRS W A SUB ADRS A DATA A STO - Multi-Data Transfer STA Slave ADRS W A Sub ADRS A DATA A Sub ADRS A DATA A --- --- Sub ADRS A DATA A STO - Automatic increment The automatic increment feature of the slave address enables a quick slave receiver initialization within one transmission by the I 2C BUS controller. STA Slave ADRS W A Auto ADRS A DATA (00H) A DATA (01H) A DATA (02H) A --- --- DATA (07H) A DATA (08H) A STO 14 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 8. I2C Write Operation: A complete data transfer MSB LSB S CL transfer ¡æ S DA W Generated by slave ST ART Slave address ACK Register address ACK Data byte ACK S T OP The automatic increment feature of the sub address enables a quick slave receiver initialization within one transmission, by the I2C Bus controller. 9. Sub Address Allocation Map (Slave address: DCH) SUB Addres [Hex] D7 00H 01H 02H 03H 04H 05H 06H 07H 08H SBLK CS1 CS2 D6 D5 Initial Value [Hex] D2 D1 D0 80H 00H 80H 80H 80H 80H 80H 80H 80H Function D4 D3 Contrast Control Brightness Control R Sub Contrast Control G Sub Contrast Control B Sub Contrast Control Cut-Off Brightness Control R Cut-Off Control G Cut-Off Control B Cut-Off Control NOTE: SBLK: Soft Blanking Switch (1: ON, 0: OFF) CS1/2: Cut-off Control Offset Current Switch (CS1: 80µA, CS2: 160µA) 15 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER - Contrast Register (SUB ADRS: 00H) (Vin = 0.56 Vpp, bright: 00H, sub: FFH) Hex 00 80 FF D7 0 1 1 D6 0 0 1 D5 0 0 1 D4 0 0 1 D3 0 0 1 D2 0 0 1 D1 0 0 1 D0 0 0 1 Contrast (Vpp) 0 1.12 4.2 0.0164 Gain (dB) -30.0 11.5 17.5 O Int value (Hex) increment/bit - Brightness Register (3-ch)(SUB ADRS: 01H) (cont: 80H, sub: FFH) Hex 00 10 1f D4 0 1 1 D3 0 0 1 D2 0 0 1 D1 0 0 1 D0 0 0 1 Brightness (V) 1 2 3 0.0625 Int. value (Hex) O increment/bit - SUB Contrast Register (R/G/B-ch)(SUB ADRS: 02/03/04H) (Vin = 0.56 Vpp, bright: 00H, cont: FFH) Hex 00 80 FF D7 0 1 1 D6 0 0 1 D5 0 0 1 D4 0 0 1 D3 0 0 1 D2 0 0 1 D1 0 0 1 D0 0 0 1 Sub Contrast (Vpp) 1.33 2.65 4.2 0.0123 Gain (dB) 7.5 13.5 17.5 O Int. value (Hex) increment/bit - Cut-Off Brightness Register (3-ch) (SUB ADRS: 05H) Hex 00 80 FF D7 0 1 1 D6 0 0 1 D5 0 0 1 D4 0 0 1 D3 0 0 1 D2 0 0 1 D1 0 0 1 D0 0 0 1 Cut-Off brightness ( µA) 0 90 180 0.703 Int. value (Hex) O increment/bit - Cut-Off Register (R/G/B-ch) (SUB ADRS: 06/07/08H) (cont: 80H, sub: FFH) Hex 00 80 FF D7 0 1 1 D6 0 0 1 D5 0 0 1 D4 0 0 1 D3 0 0 1 D2 0 0 1 D1 0 0 1 D0 0 0 1 Cut-Off (µA) 0 270 540 2.11 O Int. value (Hex) increment/bit 16 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 APPLICATION BOARD CIRCUIT VCC=12V 12V + 100uF 0.1uF Vin GND 100 1 KA78T05 Vout 3 5V U? 1 + 100uF Red In 33 75 0.1uF 10uF Red Out 2 RIN ROUT 23 390 3 Green In 33 75 GND1 GCLP 22 0.1uF 24 0.1uF VCC1 2 RCLP 10uF + 4 Green Out GIN GOUT 21 390 5 GND2 VCC3 20 0.1uF + 100uF + Blue In 33 75 10uF 6 BIN GND3 19 Blue Out + 7 0.1uF 8 + 47uF 0.1uF 9 KA2504 S1D2504A01 VCC2 BOUT 18 390 ABL BCLP 17 0.1uF 75V 16 12V 75K 75K + 100uF ABL In 100 GND(L) RCT 5V 2K 2K 10 SCL GCT 15 1uF 100V BAV21 KSP92 + KSP42 2.2K + 11 SCL SDA CLP In 5V 100 100 100 12 SDA BCT 14 100 0.47uF 50V CLP BLK 13 75V 75K BLK In 100 12V 75K BAV21 KSP92 + 1uF 100V 1 SCLK 2 SDAT 1 3 ACK 2 4 3 4 5 6 7 12 11 10 9 8 SCL SDA 100 + 1uF 100V 12V 13 KSP42 2.2K + 0.47uF 50V 74HCT125 14 100 5V 75V 75K 75K BAV21 KSP92 KSP42 2.2K 0.47uF 50V + 17 S1D2504A01 APPLICATION CIRCUIT 18 75V 75K VCC=12V + 100uF 12V KSP92 75K BAV21 0.1uF 75V + 1uF 100V KSP42 + RCLP 2.2K 1 0.1uF VCC1 + 0.47uF 50V 24 + 100uF 0.1uF 100uF 0.1uF R In 33 2 ROUT 390 75V 0.1uF 75K RIN 23 RIN VCC + G In 75 10uF B In 3 GCLP 0.1uF 100uF 0.1uF GND1 + 75K 22 VEE ROUT 27 ABL SCL 33 10uF 4 GOUT 390 27 0.1uF 1uF 100V GIN 21 GIN GND 12V BAV21 + SDA 75 KSP92 CLP 5 VCC3 + 100uF 0.1uF GND2 20 GOUT + KSP42 BLK + 2.2K 33 10uF 0.47uF 50V 6 GND3 390 27 0.1uF 12V BIN 19 BIN GND + 75 KA2504 BOUT 18 GND BOUT 75V 75K To Cathode R Out G Out B Out + 17 0.1uF 7 VCC2 S1D2504A01 100uF 0.1uF 100 8 BCLP 100 + 47uF RCT 16 ABL 0.1uF 12V 75K BAV21 9 KSP92 1uF 100V GND(L) + KSP42 2.2K 100 10 GCT 100 SCL 15 100 + 0.47uF 50V 100 11 BCT SDA 14 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER 100 12 BLK CLP 13 100 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 CHARACTERISTICS CURVE 19 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER 20 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER S1D2504A01 21 S1D2504A01 I2C BUS COTROLLED R/G/B VIDEO AMPLIFIER 22