CS3225X5R476K100NRL

TO. : NO. : APPROVAL SHEET MULTILAYER CERAMIC CAPACITOR Commercial Grade (IEC-60384 Qualified) Approved by customer : (signing or stamping here) SAMWHA CAPACITOR CO., LTD. Writtern by Checked by Approved by 2023. 02. 10. SAMWHA CAPACITOR CO., LTD. Address : 227,GYEONGGIDONG-RO, NAMSA-EUP, CHEOIN-GU, YONGIN-SI, GYEONGGI-DO, KOREA Contact : TEL 82-31-332-6441 , Home page : www.samwha.com FAX 82-31-332-7661 Contents Parts Numbering --------------------------------------------- Ⅰ. General Type ---------------------------- Page 3/16 ~ 6/16 Ⅱ. Thin Layer Large-Capacitance Type ---------- Page 7/16 ~ 9/16 Ⅲ. High Voltage Type ----------------------- Page 10/16 ~ 13/16 Enactment : March 27,1996 STANDARD NO SW - M - 04B MULTILAYER CERAMIC CAPACITOR Commercial Grade Page 1 / 16 1. General Article Application Range These specifications refer to the "Multilayer Ceramic Capacitors"mainly used to the computer equipment, communication equipment. *Caution : Industrial equipment / For the high reliability equipment / LED equipment / Etc. Please contact sales representatives or product engineers before using the products. (For details, please refer Page 16) 2. General Code (1) Type Designation CS 1608 X7R 104 K 500 N R B (1) (2) (3) (4) (5) (6) (7) (8) (9) 1) Multilayer Ceramic Capacitor (Commercial Grade) 2) Size Code : This is expressed in tens of a millimeter. The first two digits are the length, The last two digits are width. 3) Temperature Coefficient Code Classification Code Temperature Range Capacitance Tolerance Class Ⅰ C0G -55 to +125℃ ±30 ppm/℃ X5R -55 to +85℃ ±15% X7R -55 to +125℃ ±15% Y5V -30 to +85℃ +22% ~ -82% Class Ⅱ 4) Capacitance Code(Pico farads) : The nominal Capacitance Value in ㎊ is expressed by three digit numbers. The first two digits represents significant figures and the last digit denotes the number of zero ex) 104 = 100000 ㎊ R denotes decimal 8R2 = 8.2 ㎊ 5) Capacitance Tolerance Code Code 기술055(갑) Tolerance Code Tolerance B ± 0.1 ㎊ M ± 20 % C ± 0.25 ㎊ P + 100, －0% D ± 0.5 ㎊ Z + 80, －20% F ± 1.0 % H + 0.25/-0 ㎊ G ± 2.0 % I + 0/-0.25 ㎊ J ± 5 % U + 5/-0 % K ± 10 % V + 0/-5 % SAMWHA CAPACITOR CO.,LTD 70모조 A4 SW - M - 04B 2 / 16 6) Voltage Code code 6R3 100 160 250 350 500 101 201 251 501 631 102 202 302 Vol. DC 6.3V DC 10V DC 16V DC 25V DC 35V DC 50V DC 100V DC 200V DC DC 250V 500V DC 630V DC 1KV DC 2KV DC 3KV 7) Termination Code ex) N : Ni-Sn (Nickel-Tin Plate) A : Ag/Ni-Sn (Ag Epoxy/Nickel-Tin Plate) -> Soft Termination Type 8) Packing Code ex) R : 7" Reel Type L : 13" Reel Type B : Bulk Type 9) Thickness option Thickness(mm) t 0.30 0.50 0.60 0.80 0.85 1.00 1.10 1.15 1.25 Thickness(mm) Code Tol(±) 0.03 0.05 0.10 0.10 0.15 0.15 0.15 0.15 0.15 t 1.30 1.35 1.60 1.80 2.00 2.50 2.80 3.20 5.00 Blank Blank A B B E E E E Tol(±) 0.20 0.20 0.20 0.20 0.25 0.25 0.30 0.30 0.40 Code E H I J K L M N O 3. Temperature Characteristics See Page 6/16 (No.14) 4. Constructions and Dimensions (l) Dimensions (Unit : ㎜) Dimension Code 0603 1005 1608 2012 3216 3225 4520 4532 5750 Length Width L Tol(±) W Tol(±) 0.60 1.00 1.60 2.00 3.20 3.20 4.50 4.50 5.70 0.03 0.05 0.15 0.20 0.30 0.40 0.40 0.40 0.50 0.30 0.50 0.80 1.25 1.60 2.50 2.00 3.20 5.00 0.03 0.05 0.10 0.15 0.20 0.25 0.25 0.30 0.40 *1005 Size ≥4.7㎌ ⇒ L, W, T : Tol±0.15 *2012 Size ≥10㎌ ⇒ W : 1.25±0.20, T : 0.85±0.15 T1(min) G(min) 0.05 0.15 0.20 0.20 0.30 0.30 0.30 0.30 0.30 0.15 0.30 0.50 0.70 1.20 1.00 1.00 2.20 3.20 *1608 Size ≥10㎌ ⇒ W : 0.80±0.15, T : 0.80±0.15 *3216 Size ≥47㎌ ⇒ W : 1.60±0.30, T : 1.60±0.30 (2) Construction of Termination 기술055(갑) SAMWHA CAPACITOR CO.,LTD 70모조 A4 Ⅰ. General Type SW - M - 04B 3 / 16 Specifications and Test Methods (General) No. Item Specification Class Ⅰ Test Methods and Conditions Class Ⅱ 1 Operating Temperature Range X7R : -55 to +125℃ X5R : -55 to +85℃ Y5V : -30 to +85℃ 2 Insulation Resistance 3 Voltage proof No defects or abnormalities 4 Capacitance within the specified tolerance C0G :-55 to+125℃ ․Applied the rated voltage for 2 minutes of charging, The charge/discharge current is less than 50mA. C0G : The rated voltage ×300% X7R, X5R, Y5V : 〃 ×250% More than 10,000 ㏁ or 500Ω.F (Whichever is smaller) - Applied between the terminations for 1 to 5 seconds. - The charge/discharge current is less than 50mA. The capacitance/Q/D.F. should be measured at 25℃ at the requency and voltage shown in the table. Cap Char. 50V min 25V 16V 10V 6.3V 30㎊min : Q≧1,000(DF≦0.1%) 5 Dissipation Factor X7R X5R ≦2.5%/ ≦3%/ ≦3.5%/ *≦5% *≦7% *≦7% ≦5%/ ≦5%/ *≦10% *≦10% 30㎊max : Q≧400+20C (DF≦1/ (400+20C)) Y5V 6 ≦9%/ ≦12.5%/ *≦12.5% *≦15% continuously. No defects which may affect performance within ±2.5% Capacitance or ±0.25㎊ change (whichever is larger) 30㎊min : Q≧1,000 (DF≦0.1%) Resistance Dissipation Factor to 30㎊max (or Q) Soldering : Q≧400+20C Heat (DF≦1/(400+20C)) I.R. 기술055(을) ≦7%/ *≦9% 95% of the terminations is to be soldered evenly and Solderability Appearance 7 ≦5%/ *≦9% X7R, X5R: ≦ ±7.5% Y5V : ≦ ±20% Char. X7R X5R Y5V 50V min 25V 16V 10V ≦2.5%/ ≦3%/ ≦3.5%/ ≦5%/ *≦5% *≦7% *≦7% *≦10% ≦5%/ ≦7%/ ≦9%/ ≦12.5%/ *≦9% *≦9% *≦12.5% *≦15% More than 10,000㏁ or 500Ω.F (whichever is smaller) SAMWHA CAPACITOR CO.,LTD ≦15% Testing Testing frequency Voltage C0G (C10㎌) 120±24㎐ 0.5±0.1 Vrms ․ Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ․ Measurement after test Take it out and set it for 24±2 hours (Class Ⅰ) or 24±2 hours (Class Ⅱ) then measure *Pb-Free type Solder : 96.5Sn-3Ag-0.5Cu Solder temperature : 245±5℃ Immersion time : 3±0.1sec *Pre-Heating : at 80~120℃ for 10~30sec ․Preheat the capacitor at 120 to 150℃ for 1 minute. (Preheating for 3225,4520,4532 Step1:100℃ to 120℃, 1min Step2:170℃ to 200℃, 1min ) 6.3V Immerse the capacitor in a eutectic solder solution ≦5%/ *≦10% ․Soldering Temp:260 ±5℃ ․Immersion Time:10 ±0.5 sec ․Initial measurement ≦15% Perform the initial measurement according to Note1 for Class Ⅱ ․Measurement after test Take it out and set it for 24±2 hours (Class Ⅰ) or 24±2 hours (Class Ⅱ) then measure 70모조 A4 SW - M - 04B 4 / 16 Specification No. Item Appearance Capacitance Change Class Ⅰ Rapid change of temperature Dissipation Factor (or Q) I.R Perform the five cycles according to the four heat treatments listed in the following table. No defects which may affect performance Within ±2.5% or ±0.25㎊ (whichever is larger) X7R, X5R : Within ±7.5% Y5V : Within ±20% Char 8 Test Methods and Conditions Class Ⅱ 30㎊min X7R : Q≧1,000 (DF≦0.1%) X5R 30㎊max : Q≧400+20C (DF≦1/(400+20C)) Y5V 50V min 25V 16V 10V 6.3V ≦5%/ ≦5%/ ≦5%/ ≦7.5%/ ≦7.5%/ *≦7.5% *≦10% *≦10% *≦12.5 *≦12.5% ≦7.5%/ ≦10%/ *≦12.5% *≦12.5% ≦12.5%/ ≦15%/ *≦15% *≦20% ≦20% Accelerated steady state More than 10,000㏁ or 500Ω.F (Whichever is smaller) No defects which may affect performance X7R, X5R : Within ±12.5% Within ±7.5% C ap a c it a n c e Y5V : Within +30%, -40% or ±0.75㎊ Change (Y5V/1.0㎌,2.2㎌,4.7㎌/10V) (whichever is larger) Within ±30% (others) 30㎊min 50V 25V 16V 10V : Q≧200 (DF≦0.5%) Char min Dissipation Factor(or Q) 30㎊max : Q≧100+10/3C DF≦1/(100+10/3C) X7R X5R Y5V I.R Appearance Capacitance Change 10 Endurance Dissipation Factor (or Q) I.R 기술055(을) 6.3V ≦5%/ ≦5%/ ≦5%/ ≦7.5%/ *≦7.5% *≦10% *≦10% *≦12.5 *≦12.5% ≦7.5%/ ≦10%/ *≦12.5% *≦12.5% ≦12.5%/ ≦15%/ *≦15% *≦20% ≦7.5%/ ≦20% More than 500㏁ or 25Ω.F (Whichever is smaller) No defects which may affect performance Within ±3% or ±0.3㎊ (whichever is larger) Char 10㎊≦Cp≦30㎊ : Q≧275+5/2C (DF≦1/(275+5/2C)) X7R X5R 10㎊max : Q≧200+10C (DF≦1/(200+10C)) Y5V 50V min 25V 16V 10V 6.3V ≦7.5%/ ≦5%/ ≦5%/ ≦5%/ ≦7.5%/ *≦10% *≦10% *≦12.5 *≦12.5% ≦7.5%/ ≦10%/ ≦12.5%/ ≦15%/ *≦15% 3 4 Temp (℃) Room Temp Max. operating temp. +3, -0 Room Temp Time (min) 30±3 2 to3 30±3 2 to3 ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ *≦20% More than 1,000㏁ or 50Ω.F (whichever & smaller) SAMWHA CAPACITOR CO.,LTD ․Temperature : 40±2℃ ․Humidity : 90~95%RH ․Hour : 500+24/-0 hrs ․Applied Voltage : Rated Voltage The charge/discharge current is less than 50mA. ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ․Measurement after test Perform the final measurement according to Note2 ․Applied voltage : Rated voltage〈 DC250V : ×200% *≦7.5% *≦12.5% *≦12.5% 2 ․Testing time : 1000+48/-0 hrs X7R, X5R : Within ±12.5% Y5V : Within ±30% (cap＜1.0㎌) Within +30%, -40% (cap≧1.0㎌) 30㎊min : Q≧350 (DF≦0.3%) 1 Min. operating temp. +0, -3 ․Measurement after test Perform the final measurement according to Note2 Appearance 9 damp heat, Step ․Temperature : C0G, X7R → 125±3℃ X5R, Y5V → 85±3℃ The charge/discharge current is less than 50mA. ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ≦20% ․Measurement after test Perform the final measurement according to Note2 70모조 A4 SW - M - 04B 5 / 16 Specification No. Item Class Ⅰ Test Methods and Conditions Class Ⅱ ․Substrate material : Glass EPOXY Board. 11 ․Thickness : 1.6㎜ 0.8㎜(0603/1005size) Substrate bending test *. Test condition - Bending limit : 1mm - Pressurizing speed : 1mm/sec - Holding time : 5±1sec No cracking or marking defects shall occur Capacitance Change Within ±5% or ±0.5pF (whichever is larger) X7R, X5R: Within ±10% Y5V: Within ±30% Appearance No defects or abnormalities Capacitance Whin the specified tolerance Char. 12 Vibration Q/DF 30㎊min : Q≧1,000 (DF≦0.1%) 30㎊max : Q≧400+20C X7R X5R (DF≦1/ (400+20C)) Y5V Appearance Capacitance Change 50V min 25V 16V ≦2.5%/ ≦3%/ ≦3.5%/ ≦5%/ ≦5%/ *≦5% *≦7% *≦7% *≦10% *≦10% ≦5%/ ≦7%/ ≦9%/ ≦12.5%/ *≦9% *≦9% *≦12.5% *≦15% 10㎊≦Cp≦30㎊ X7R : Q≧275+5/2C X5R (DF≦1/(275+5/2C)) 10㎊max : Q≧200+10C (DF≦1/(200+10C)) I.R. 기술055(을) ≦15% ․Temperature : 40±2℃ within ±5% or ±0.5㎊ X7R, X5R: Within ±12.5% (Whichever is larger) Y5V: Within ±30% min Damp heat, steady state Dissipation (or Q) 6.3V No defects which may affect performance 30㎊ min 50V : Q≧350 (DF≦0.3%) Char 13 10V *After soldering and then let sit for 24±2hr(temperature compensating type), 24±2hr(high dielectric constant type) at room temperature. The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55Hz, shall be traversed(from 10Hz to 55Hz then 10Hz again) in approximately 1 minute. This motion shall be applied for a period of 2 hours in each 3mutually perpendicular directions(total is 6hours). Y5V 25V ․Humidity : 90~95%RH 16V 10V 6.3V ≦7.5%/ ≦5%/ ≦5%/ ≦5%/ ≦7.5%/ *≦7.5% *≦10% *≦10% *≦12.5 *≦12.5% ≦7.5%/ ≦10%/ *≦12.5% *≦12.5% ≦12.5%/ ≦15%/ *≦15% *≦20% ․Hour : 500+24/-0 hrs ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ≦20% ․Measurement after test Perform the final measurement according to Note2 More than 1,000㏁ or 50Ω.F (Whichever is smaller) SAMWHA CAPACITOR CO.,LTD 70모조 A4 SW - M - 04B 6 / 16 Specification No. Item Test Methods and Conditions Class Ⅰ 14 Class Ⅱ Temperature Capacitance characteristic Change of capacitance Temp Reference Cap Char. Range Temp. Change X7R Temperature Coefficient Temp Char. Range C0G Within ±15% -55 to +125℃ X5R -55 to +85℃ Y5V -30 to +85℃ 25℃ Within ±15% Within +22% -82% Temperature Coefficient -55 to ±30 ppm/℃ +125℃ (1) Temperature Compensating Type The tem perature coefficient is determined using the capacitance measured in step 3 as a reference, W hen cycling the tem perature sequentially from step 1 through 5,(C0G: +25 to 125℃) the capacitance shall be with in the specified tolerance for the temperature coefficient. The capacitance drift is calculated by dividing the difference between the maximum measured values in the step 1, 3 and 5 by the cap. value in step 3 Step Temperature(℃) 1 25±2 2 -55±3 3 25±2 4 125±3(for C0G) 5 25±2 (2) High Dielectric Constant Type The ranges of capacitance change compared with the 25℃ value over the temperature range shown in the table shall be in the specified range. *Note1. Initial Measurement for Class Ⅱ Perform a heat treatment at 150+0,-10℃ for one hour and then let sit for 24±2 hours at room temperature,then measure *Note2. Measurement after test 1.Class Ⅰ Let sit for 24±2 hours at room temperature,then measurement 2.Class Ⅱ Perform a heat treatment at 150+0,-10℃ for one hour and then let sit for 24±2 hours at room temperature,then measure. "Following the International standards, the title of each test item is subject to change." 기술055(을) SAMWHA CAPACITOR CO.,LTD 70모조 A4 Ⅱ. Thin Layer Large-Capacitance Type SW - M - 04B Specifications and Test Methods (Thin Layer Large-Capacitance Type) No. 1 2 3 4 Item Specification Operating X7R : -55 to +125℃ Temperature X5R : -55 to +85℃ Range Y5V : -30 to +85℃ Insulation Voltage proof Capacitance Test Methods and Conditions ․Applied the rated voltage for 2 minutes of charging, The charge/discharge current is less than 50mA. 50Ω․F min Resistance 7 / 16 No defects or abnormalities X7R, X5R, Y5V : The rated voltage × 250% - Applied between the terminations for 1 to 5 seconds. within the specified tolerance - The charge/discharge current is less than 50mA. The capacitance/D.F. should be measured at 25℃ at the frequency and voltage shown in the table. 5 Dissipation Factor X7R, X5R : 12.5%max *3216 Size 100㎌ : 15%max Y5V : 20%max Capacitance Frequency Voltage C≦10㎌ 1 ± 0.1kHz 0.5~1.0Vrms C>10㎌ 120 ± 24Hz 0.5±0.1Vrms ․ Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ․ Measurement after test Take it out and set it for 24±2 hours (Class Ⅱ) then measure *Pb-Free type 6 Solderability Appearance 95% of the terminations is to be soldered evenly and Solder : 96.5Sn-3Ag-0.5Cu Solder temperature : 245±5℃ continuously. Immersion time : 3±0.1sec No defects which may affect performance Capacitance X7R, X5R : Within±7.5% Resistance 7 to Soldering Heat change Y5V Dissipation X7R, X5R : 12.5%max *3216 Size 100㎌ : 15%max Factor Y5V : Within±20% : 20%max 260±5℃ for 10±0.5 seconds. ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ 50Ω․F min ․Measurement after test Let sit at room temperature for 24±2 hours,then measure. Appearance No defects which may affect performance Perform the five cycles according to the four heat treatments listed in the following table. Rapid Dissipation change of Factor temperature I.R 기술055(을) (Preheating for 3225,4520,4532 Step1:100℃ to 120℃, 1min Step2:170℃ to 200℃, 1min ) Immerse the capacitor in a eutectic solder solution at I.R. Capacitance X7R, X5R : Within ±7.5% Change Y5V : Within ±20% 8 *Pre-Heating : at 80~120℃ for 10~30sec Preheat the capacitor at 120 to 150℃ for 1 minute. X7R, X5R : 12.5%max *3216 Size 100㎌ : 15%max Y5V 50Ω․F min : 20%max Step 1 2 3 4 Temp (℃) Min. operating temp. +0/-3 Room Temp Max. operating temp. +3/-0 Room Temp Time (min) 30±3 2 to3 30±3 2 to3 ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ․Measurement after test Perform the final measurement according to Note2 SAMWHA CAPACITOR CO.,LTD 70모조 A4 SW - M - 04B No. 9 Item Endurance Specification Appearance No defects which may affect performance Capacitance Change X7R, X5R : Within ±12.5% Y5V : Within ±30% Dissipation Factor I.R X7R, X5R : 20%max *3216 Size 100㎌ : 30%max Y5V : 40%max 8 / 16 Test Methods and Conditions Apply 150% of the rated voltage for 1000+48/-0 hrs at the maximum operating temperature ±3℃. The charge/discharge current is less than 50mA. -Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ -Measurement after test Perform the final measurement according to Note2 12.5Ω․F min ․Substrate material : Glass EPOXY Board. 10 ․Thickness : 1.6㎜ 0.8㎜(0603/1005size) Substrate bending test *. Test condition - Bending limit : 1mm - Pressurizing speed : 1mm/sec - Holding time : 5±1sec No cracking or marking defects shall occur Capacitance Change X7R, X5R: Within ±10% Y5V : Within ±30% Within +30/-40% (cap≥10㎌) Appearance No defects or abnormalities Capacitance Whin the specified tolerance 11 Vibration X7R, X5R : 12.5%max D i s s i p a t i o n *3216 Size 100㎌ : 15%max Factor Y5V : 20%max Appearance Accelerated 12 damp heat, steady state Capacitance X7R, X5R: Within ±12.5% Change Y5V Dissipation Factor I.R. 기술055(을) No defects which may affect performance : Within ±30% X7R, X5R : 20%max *3216 Size 100㎌ : 30%max Y5V : 40%max 12.5Ω․F min After soldering and then let sit for 24±2hr at room temperature. The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55Hz, shall be traversed(from 10Hz to 55Hz then 10Hz again) in approximately 1 minute. This motion shall be applied for a period of 2 hours in each 3mutually perpendicular directions(total is 6hours). Apply the rated voltage at 40±2℃ and 90 to 95%RH for 500+24/-0 hrs. The charge/discharge current is less than 50mA. ․Initial measurement Perform the initial measurement according to Note1 for Class Ⅱ ․Measurement after test Perform the final measurement according to Note2 SAMWHA CAPACITOR CO.,LTD 70모조 A4 SW - M - 04B No. 13 Item Specification 9 / 16 Test Methods and Conditions Char. Temp. Range Temperature characteristic Reference Temp. X5R -55 to +85℃ 25℃ Within ±15% of capacitance X7R -55 to +125℃ 25℃ Within ±15% Y5V -30 to +85℃ 25℃ Within +22/-82% Cap. Change The capacitance change should be measured after 5 min. at each specified temperature stage. The ranges of capacitance change compared with the 25℃ value over the temperature ranges shown in the table should be within the specified ranges. *Note1. Initial Measurement for Class Ⅱ Perform a heat treatment at 150+0,-10℃ for one hour and then let sit for 24±2 hours at room temperature,then measure *Note2. Measurement after test Class Ⅱ Perform a heat treatment at 150+0,-10℃ for one hour and then let sit for 24±2 hours at room temperature,then measure. "Following the International standards, the title of each test item is subject to change." 기술055(을) SAMWHA CAPACITOR CO.,LTD 70모조 A4 Ⅲ. High Voltage Type SW - M - 04B 10 / 16 Specifications and Test Methods (High voltage type) Specification No. Item Test Methods and Conditions Class Ⅰ Class Ⅱ X7R : -55 to +125℃ 1 Operating Temperature Range C0G :-55 to+125℃ 2 Dimensions Within the specified dimension Using calipers No failure should be observed when voltage in table is applied between the terminations, provided the charge/discharge current is less than 50mA. Cap. Rated voltage DC100V~630V 3 Voltage proof No defects or abnormalities C0G DC1kV, DC2kV DC3kV, DC3.15kV DC100V~630V DC1kV X7R DC2kV DC3kV 4 Insulation Resistance 5 Capacitance More than 10,000 ㏁ Cap C0G 6 Dissipation Factor Time 120% of the rated voltage 150% of the rated voltage 1to5 sec. 120% of the rated voltage Rated voltage < DC500V : Applied the rated voltage for -DC100V~1KV 2 minutes of charging. :C≥0.01㎌:More than 100㏁․㎌ :C