SVC241D-05A

SVC Varistors Type SVC Varistors Type Introduction SVC series Varistors are gapless ceramic surge absorbers of a new type made of metal oxide which is designed to protect various kinds of electronic devices and semiconducting elements from surges. Suffix Code Taping Type Code 5 7 8 9 1 Bulk Type Pitch of Component(mm) 12.7 15.0 30.0 25.4 30.0 Lead Spacing(mm) 5.0 7.5 7.5 7.5 10.0 Code 5 7 1 Lead Spacing(mm) 5.0 7.5 10.0 DISC Ceramic Capacitors www.samwha.com F 114 Features High discharge current capability up to 4000 Amps. Excellent clamping characteristics. Fast response time under 50 nanesesconds. Improve Product safety UL, CSA, VDE recognized SVC Characteristic Curves V - Ⅰ Curve Small - current region of V -Ⅰcurve Temporary power frequency over voltage capability How to Order SVC 471 D-14A FF 7 Basic Type ZnO Varistor Varistor Nominal Voltage (The first two digit indicate significaticant digits) (The 3rd digit indicate the number of zeros following) Style D : Disk Type Varistor B Type Packing Style & Lead Variation Lead Spacing & Pitch of Component Withstand discharge impulse current characteristics(Typical) A Type Withstand discharge impulse current characteristics(Typical) Chip Element Size(Dia) 05 : Ø5mm, 07 : Ø7mm, 10 : Ø10mm, 14 : Ø14mm, 20 :Ø20mm Classification A : High Voltage(82V and above) B : Low Voltage(less then 68V) Packing Style S Taping Type Flat Pack K F Lead Variation Straight Type In-Kink Type Out-Kink Type B Packing Style S W Bulk K L N Lead Variation Straight Long Type Kink Short Type Kink Long Type Kink Short Type Straight Short Type SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 115 SVC Varistors Type Specification Maximum Ratings Applied Voltage Chip Element RMS DC Size 50/60Hz (25℃ ) (25℃ ) Dia (mm) SVC 180D-05B SVC 180D-07B SVC 180D-10B 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 60 85 50 65 40 56 35 45 30 38 25 31 20 26 17 22 14 18 11 14 Characteristics Nominal Varistor ④ Peak Voltage Vnom (Volts) Tolerance Min.(Volts) Max.(Volts) Max. Clamping ⑤ Typical Voltage @ Test Capacitance Current(8/20㎲) Vc (Volts) 40 36 18 16 20 36 36 36 48 43 22 20 24 43 43 43 60 53 27 24 30 53 54 53 73 65 33 30 36 65 65 65 86 77 39 35 43 77 77 77 104 93 47 42 52 93 93 93 123 110 56 50 62 110 110 110 150 135 68 61 75 135 135 135 145 135 82 74 90 135 135 135 175 165 100 90 110 165 165 165 Maximum Ratings Applied Voltage Chip Element RMS DC Size 50/60Hz (25℃ ) (25℃ ) Dia (mm) SVC 121D-05A SVC 121D-07A SVC 121D-10A SVC 121D-14A SVC 121D-20A SVC 151D-05A SVC 151D-07A SVC 151D-10A SVC 151D-14A SVC 151D-20A SVC 201D-05A SVC 201D-07A SVC 201D-10A SVC 201D-14A SVC 201D-20A SVC 221D-05A SVC 221D-07A SVC 221D-10A SVC 221D-14A SVC 221D-20A SVC 241D-05A SVC 241D-07A SVC 241D-10A SVC 241D-14A SVC 241D-20A SVC 271D-05A SVC 271D-07A SVC 271D-10A SVC 271D-14A SVC 271D-20A SVC 361D-05A SVC 361D-07A SVC 361D-10A SVC 361D-14A SVC 361D-20A SVC 391D-05A SVC 391D-07A SVC 391D-10A SVC 391D-14A SVC 391D-20A SVC 431D-05A SVC 431D-07A SVC 431D-10A SVC 431D-14A SVC 431D-20A SVC 471D-05A SVC 471D-07A SVC 471D-10A SVC 471D-14A SVC 471D-20A 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 5 7 10 14 20 300 385 275 350 250 320 230 300 175 225 150 200 140 180 130 170 95 125 75 100 Characteristics Nominal Varistor ④ Peak Voltage Vnom (Volts) Tolerance Min.(Volts) Max.(Volts) Max. Clamping ⑤ Typical Voltage @ Test Capacitance Current(8/20㎲) Vc (Volts) 210 200 120 108 132 200 200 200 260 250 150 135 165 250 250 250 355 340 200 185 225 340 340 340 380 360 220 198 242 360 360 360 415 395 240 216 264 395 395 395 475 455 270 247 303 455 455 455 620 595 360 324 396 595 595 595 675 650 390 351 429 650 650 650 754 710 430 387 473 710 710 710 810 775 470 423 517 775 775 775 Transient Energy ② Wtm (Joules) 0.3 0.8 1.5 3.5 10.0 0.4 0.9 2.0 4.0 13.0 0.5 1.0 2.5 5.0 15.0 0.6 1.2 3.0 6.0 20.0 0.8 1.5 3.5 7.0 24.0 1.0 1.8 4.5 8.5 30.0 1.0 2.2 5.5 10.5 35.0 1.2 2.5 6.5 12.0 40.0 1.7 3.5 8.0 14.0 27.0 2.0 4.0 10.0 18.0 30.0 Transient Energy ② Wtm (Joules) 2.5 5.0 12.0 20.0 40.0 3.0 6.0 16.0 25.0 50.0 4.0 10.0 20.0 35.0 70.0 4.5 10.0 23.0 40.0 75.0 5.0 10.0 25.0 40.0 80.0 6.0 12.0 30.0 50.0 90.0 7.5 15.0 35.0 65.0 120.0 8.0 17.0 40.0 70.0 130.0 9.0 20.0 45.0 75.0 140.0 10.0 20.0 45.0 80.0 150.0 Device Type Average Peak ③ Current Power Dissipation (8/20㎲) Ptam (Watts) 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.01 0.02 0.05 0.1 0.2 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 Device Type Average Peak ③ Current Power Dissipation (8/20㎲) Ptam (Watts) 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 0.1 0.25 0.4 0.6 1.0 Vacm (Volts) Vdcm (Volts) Itm (Amps) 125 250 500 1000 2000 125 250 500 1000 2000 125 250 500 1000 2000 125 250 500 1000 2000 125 250 500 1000 2000 125 250 500 1000 2000 125 250 500 1000 2000 125 250 500 1000 2000 400 1200 2500 4500 6500 400 1200 2500 4500 6500 Ip (Amps) 1 2.5 5 10 20 1 2.5 5 10 20 1 2.5 5 10 20 1 2.5 5 10 20 1 2.5 5 10 20 1 2.5 5 10 20 1 2.5 5 10 20 1 2.5 5 10 20 5 10 25 50 100 5 10 25 50 100 f=1kHz (㎊) 1700 3500 7000 1400 28000 1200 2500 5000 11000 22000 1100 2000 4500 9000 18000 1000 2000 4000 8000 16000 800 1600 3200 6500 13000 700 1400 2800 5500 11000 600 1300 2500 5000 10000 500 1000 2000 4000 8000 400 800 1500 3000 6000 350 700 1500 3000 6000 Vacm (Volts) Vdcm (Volts) Itm (Amps) 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 400 1200 2500 4500 6500 Ip (Amps) 5 10 25 50 100 5 10 25 50 100 5 10 25 50 100 5 10 25 50 100 5 10 25 50 100 5 10 25 50 100 5 10 25 50 100 2.55 10 25 50 100 5 10 25 50 100 5 10 25 50 100 f=1kHz (㎊) 350 700 1300 2600 5200 250 500 1000 2000 4000 200 400 800 1600 3200 170 350 700 1400 2800 170 350 700 1300 2600 150 300 600 1200 2400 120 250 500 1000 2000 110 220 450 900 1800 100 200 400 800 1600 80 170 350 700 1400 DISC Ceramic Capacitors www.samwha.com SVC 180D-14B SVC 180D-20B SVC 220D-05B SVC 220D-07B SVC 220D-10B SVC 220D-14B SVC 220D-20B SVC 270D-05B SVC 270D-07B SVC 270D-10B SVC 270D-14B SVC 270D-20B SVC 330D-05B SVC 330D-07B SVC 330D-10B SVC 330D-14B SVC 330D-20B SVC 390D-05B SVC 390D-07B SVC 390D-10B SVC 390D-14B SVC 390D-20B SVC 470D-05B SVC 470D-07B SVC 470D-10B SVC 470D-14B SVC 470D-20B SVC 560D-05B SVC 560D-07B SVC 560D-10B SVC 560D-14B SVC 560D-20B SVC 680D-05B SVC 680D-07B SVC 680D-10B SVC 680D-14B SVC 680D-20B SVC 820D-05A SVC 820D-07A SVC 820D-10A SVC 820D-14A SVC 820D-20A SVC 101D-05A SVC 101D-07A SVC 101D-10A SVC 101D-14A SVC 101D-20A 116 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 117 SVC Varistors Type Dimensions Maximum Ratings Applied Voltage Chip Element RMS DC Size 50/60Hz (25℃ ) (25℃ ) Dia (mm) SVC 561D-10A SVC 561D-14A SVC 561D-20A 10 14 20 10 14 20 10 14 20 10 14 20 10 14 20 10 14 20 10 14 20 10 14 20 10 14 20 14 20 1000 1465 680 895 625 825 550 745 510 670 485 640 460 615 420 560 385 550 350 460 (Unit:mm) A Type Type SVC 471D-05A SVC 820D-07A SVC 101D-07A SVC 121D-07A SVC 151D-07A SVC 201D-07A SVC 221D-07A SVC 241D-07A SVC 271D-07A SVC 361D-07A SVC 391D-07A SVC 431D-07A SVC 471D-07A SVC 820D-10A SVC 101D-10A SVC 121D-10A SVC 151D-10A SVC 201D-10A SVC 221D-10A SVC 241D-10A SVC 271D-10A SVC 361D-10A SVC 391D-10A SVC 431D-10A SVC 561D-10A SVC 621D-10A SVC 681D-10A SVC 751D-10A SVC 781D-10A SVC 821D-10A SVC 911D-10A SVC 102D-10A SVC 112D-10A SVC 820D-14A SVC 101D-14A SVC 121D-14A SVC 151D-14A SVC 201D-14A SVC 221D-14A SVC 241D-14A SVC 271D-14A SVC 361D-14A SVC 391D-14A SVC 431D-14A SVC 471D-14A SVC 561D-14A SVC 621D-14A SVC 681D-14A SVC 751D-14A SVC 781D-14A SVC 821D-14A SVC 911D-14A SVC 102D-14A SVC 112D-14A SVC 182D-14A SVC 820D-20A SVC 101D-20A SVC 121D-20A SVC 151D-20A SVC 201D-20A SVC 221D-20A SVC 241D-20A SVC 271D-20A SVC 361D-20A SVC 391D-20A SVC 431D-20A SVC 471D-20A SVC 561D-20A SVC 621D-20A SVC 681D-20A SVC 751D-20A SVC 781D-20A SVC 821D-20A SVC 911D-20A SVC 102D-20A SVC 112D-20A SVC 182D-20A Characteristics Nominal Varistor ④ Peak Voltage Vnom (Volts) 560 T Max. D Max. H Max. L Min. 6.0 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 6.0 6.0 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 6.0 7.5 7.5 7.5 8.5 8.5 8.5 10.5 10.5 10.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 6.0 6.0 7.5 7.5 7.5 8.5 8.5 8.5 10.5 10.5 10.5 15.0 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 6.0 6.0 7.5 7.5 7.5 8.5 8.5 8.5 10.5 10.5 10.0 15.0 7.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 23.0 23.0 23.0 23.0 23.0 23.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 24.0 10.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 F 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 Ød 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 Transient Energy ② Wtm (Joules) 45.0 85.0 150.0 45.0 85.0 150.0 45.0 90.0 160.0 50.0 100.0 175.0 50.0 105.0 180.0 55.0 110.0 190.0 60.0 120.0 215.0 65.0 130.0 230.0 70.0 140.0 250.0 24.0 400.0 Device Type Average Peak ③ Current Power Dissipation (8/20㎲) Ptam (Watts) 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.4 0.6 1.0 0.6 1.0 Max. Clamping ⑤ Typical Voltage @ Test Capacitance Current(8/20㎲) Vc (Volts) 920 920 920 1025 Vacm (Volts) Vdcm (Volts) Itm (Amps) 2500 4500 8000 2500 4500 8000 2500 4500 8000 2500 4500 8000 2500 4500 6500 2500 4500 6500 2500 4500 6500 2500 4500 6500 2500 4500 6500 4500 6500 Tolerance Min.(Volts) Max.(Volts) 504 616 Ip (Amps) 25 50 100 25 50 100 25 50 100 25 50 100 25 50 100 25 50 100 25 50 100 25 50 100 25 50 100 50 100 f=1kHz (㎊) 300 600 1200 270 550 1100 250 500 1000 220 450 900 220 440 880 210 420 840 180 380 750 180 350 700 150 300 600 200 400 SVC 621D-10A SVC 621D-14A SVC 621D-20A SVC 681D-10A SVC 681D-14A SVC 681D-20A SVC 751D-10A SVC 751D-14A SVC 751D-20A SVC 781D-10A SVC 781D-14A SVC 781D-20A SVC 821D-10A SVC 821D-14A SVC 821D-20A SVC 911D-10A SVC 911D-14A SVC 911D-20A SVC 102D-10A SVC 102D-14A SVC 102D-20A SVC 112D-10A SVC 112D-14A SVC 112D-20A SVC 182D-14A SVC 182D-20A Straight Type Forming Type DISC Ceramic Capacitors www.samwha.com 620 558 682 1025 1025 1120 B Type Type SVC 180D-05B SVC 220D-05B SVC 270D-05B SVC 330D-05B SVC 390D-05B SVC 470D-05B SVC 560D-05B SVC 680D-05B SVC 180D-07D SVC 220D-07D SVC 270D-07D SVC 330D-07D SVC 390D-07D SVC 470D-07D SVC 560D-07D SVC 680D-07D SVC 180D-10B SVC 220D-10B SVC 270D-10B SVC 330D-10B SVC 390D-10B SVC 470D-10B SVC 560D-10B SVC 680D-10B SVC 180D-14B SVC 220D-14B SVC 270D-14B SVC 330D-14B SVC 390D-14B SVC 470D-14B SVC 560D-14B SVC 680D-14B SVC 180D-20B SVC 220D-20B SVC 270D-20B SVC 330D-20B SVC 390D-20B SVC 470D-20B SVC 560D-20B SVC 680D-20B 680 612 748 1120 1120 1240 T Max. D Max. H Max. L Min. 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 17.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 F 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 Ød 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 750 675 825 1240 1240 1290 780 702 858 1290 1290 1355 820 738 902 1355 1355 1500 910 819 1001 1500 1500 1650 1000 900 1100 1650 1650 1815 1100 990 1210 1815 1815 2970 2970 1800 1620 1980 Notes : ① The waveform of the maximum DC applied voltage is flat. When a ripple voltage as from a rectifier source is supplied make sure that the peak voltage is kept under th Vdcm An AC applied voltage(50/60Hz) form a since waveshape. When the distortion in the waveform is extensive make sure that the peak voltage is less than times the Vacm. ② Energy : Wtm Transient energy ratings are given in the Wtm column of the specifications in Joules(watt-second). The rating is the maximum allowable energy for a single impulse of 2ms square-waveform current with continuous voltage applied. Energy ratings are based on a shift of Vnom of less than ±10% of initial value. ③ Transient peak current(Itm) The peak current rating. Itm. of varistor is based on an 8/20 ㎲ test impulse waveshape. This peak current is the maximum peak current in which the nominal varistor voltage shift does not exceed ±10% when the test impulse is applied once at 5 mimutes intervals. ④ Nominal varistor voltage : Vnom Indicates the varistor terminal voltage measured with a 1mA DC applied. -0.1mA DC in the case of the 0.5A and 05B series. ⑤ Maximum clamping voltage : Vc Indicates the peak teminal voltage measured with an 8/20㎲ impulse current applied. Operating ambient temperature : -40℃ to +80℃ Storage temperature : -40℃ to +125℃ UL and CSA recognized(UL 1449, UL 497B or UL 1414, CSA) SVC varistors have been tested by Underwiter’s Laboratories, Inc. and Canadian Standards Association UL File No. E97754, E151195, E154171. CSA File No. LR78923. Type SVC 820D-05A SVC 101D-05A SVC 121D-05A SVC 151D-05A SVC 201D-05A SVC 221D-05A SVC 241D-05A SVC 271D-05A SVC 361D-05A SVC 391D-05A SVC 431D-05A T Max. D Max. H Max. L Min. 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 25 25 25 25 25 25 25 25 25 25 25 F 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 Ød 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 118 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 119 SVC Varistors Type FS5 Type Item Body Diameter Body Thickness Lead Diameter Pitch of sprocket Hole Pitch of Component Lead Length from Hole Center Lead Lead Length from Hole Center to Component Center Lead Spacing Deviation Along Tape. Left or Right Deviation Across Tape Carrier Tape Width Hold Down Tape Width Position of Sprocket Hole Hole Down Tape Position Lead-Wire Clinch Height Height of Component Hole Component Height Diameter of Sprocket Hole Length of Snipped Lead Total Tape Thickness Total Thickness Tape and Lead Wire Length of Snipped Lead Code Dimensions(mm) FS5 or FK5 FF9 D See page 119 T See page 119 Ød 0.5/0.50±0.05 0.6-0.8±0.05 P0 12.7±0.3 P 6.35±1.3 25.4±1.0 P1 3.85±0.7 8.95±1.0 P2 F ΔS Δh W W0 W1 W2 H0 H H1 ØD0 L t1 t2 Lx 6.35±1.3 5.0 -0.2 +0.8 Char, Curves and Lifetime Transient V-I Charactic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2-minute interval Up to 106 - pulse : 10-second interval 05B(SVC 180D-05B to SVC 680D-05B) 05B(SVC 180D-05B to SVC 680D-05B) 12.7±1.5 Voltage (V) DISC Ceramic Capacitors www.samwha.com FK5 Type FF9 Type 7.5±1.0 0±1.0 0±2.0 +1.0 18.0 -0.5 5.0Min. 9.0Min. 9.0±0.5 3.0Max. 16.0±0.5 +1.5 20.0 -1.0 32.25Max. 4.0±0.2 11.0Max. 0.7±0.2 1.5Max. 1.7Max. 1.0Max. Item Body Diameter Body Thickness Lead Diameter Pitch of sprocket Hole Pitch of Component Lead Length from Hole Center Lead Lead Length from Hole Center to Component Center Lead Spacing Deviation Along Tape. Left or Right Deviation Across Tape Carrier Tape Width Hold Down Tape Width Position of Sprocket Hole Hole Down Tape Position Lead-Wire Clinch Height Height of Component Hole Component Height Diameter of Sprocket Hole Length of Snipped Lead Total Taps Thickness Total Thickness Tape and Lead Wire Length of Snipped Lead Code D T Ød P0 P P1 P2 F ΔS Δh W W0 W1 W2 H0 H H1 ØD0 L t1 t2 Lx Dimensions(mm) FF7 FF8 See page 119 See page 119 0.6-0.8±0.05 15.0±0.3 15.0±0.3 30.0±1.0 3.75±1.0 7.50±1.5 7.5±1.0 0±1.0 0±2.0 +1.0 18.0 -0.5 5.0Min. 9.0±0.5 3.0Max. 16.0±0.5 20.0 -1.0 40.00Max. 4.0±0.2 11.0Max. 0.7±0.2 1.7Max. 1.0Max. +1.5 FF7 Type 05A(SVC 820D-05A to SVC 471D-05A) 05A(SVC 820D-05A to SVC 471D-05A) Max idle current SVC 361D-05A SVC391D-05A SVC 431D-05A Max clamping voltage 5A SVC 471D-0 SVC 471D-05A SVC 431D-05A SVC 391D-05A SVC 361D-05A SVC 271D-05A SVC 241D-05A SVC 221D-05A SVC 201D-05A 5A 1D-0 SVC 15 5A 1D-0 SVC 12 5A 1D-0 SVC 10 5A 0D-0 SVC 82 5A 1D-0 SVC 27 1D-05A SVC 24 1D-05A SVC 20 -05A 151D SVC 5A 1D-0 12 SVC -05A 121D SVC A D-05 820 SVC SVC -05A 221D FF8 Type Current (A) 120 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 121 SVC Varistors Type Transient V-I Characteristic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2-minute interval Up to 10 -pulse : 10-second interval 6 Transient V-I Characteristic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2-minute interval Up to 106-pulse : 10-second interval 07B(SVC 180D-07B to SVC 680D-07B) 07B(SVC 180D-07B to SVC 680D-07B) 10B(SVC 180D-10B to SVC 680D-10B) 10B(SVC 180D-10B to SVC 680D-10B) DISC Ceramic Capacitors SVC Max idle current Max clamping voltage SVC 180D-1 0B 180 D-1 0B 07A(SVC 820D-07A to SVC 471D-07A) 07A(SVC 820D-07A to SVC 471D-07A) 10A(SVC 820D-10A to SVC 471D-10A) 10A(SVC 820D-10A to SVC 471D-10A) www.samwha.com 122 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 123 SVC Varistors Type Transient V-I Characteristic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2-minute interval Up to 10 -pulse : 10-second interval 6 Transient V-I Characteristic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2-minute interval Up to 106-pulse : 10-second interval 10A(SVC 561D-10A to SVC 112D-10A) 10A(SVC 561D-10A to SVC 112D-10A) 14A(SVC 820D-14A to SVC 471D-14A) 14A(SVC 820D-14A to SVC 471D-14A) DISC Ceramic Capacitors 14B(SVC 180D-14B to ENC 680D-14B) www.samwha.com 124 SAMWHA CAPACITOR Co., Ltd. 1- pu lse 14B(SVC 180D-14B to SVC 680D-14B) 14A(SVC 561D-14A to SVC 182D-14A) 14A(SVC 561D-14A to SVC 182D-14A) DISC Ceramic Capacitors 125 SVC Varistors Type Transient V-I Characteristic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2-minute interval Up to 10 -pulse : 10-second interval 6 Transient V-I Characteristic Curves Current waveform under 10 A : DC over 10 A : 8/20㎲ -1 -2 Pulse Lifetime Ratings Notes : 2-pulse : 5-minute interval 3 to 10-pulse : 2- minute interval Up to 106 -pulse : 10-second interval 20B(SVC 180D-20B to SVC 680D-20B) 20B(SVC 180D-20B to SVC 680D-20B) 20A(SVC 561D-20A to SVC 182D-20A) 20A(SVC 561D-20A to SVC 182D-20A) DISC Ceramic Capacitors 20A(SVC 820D-20A to SVC 471D-20A) 20A(SVC 820D-20A to SVC 471D-20A) www.samwha.com 126 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 127 SVC Varistors Type Applications The Protection of semiconducting elements such as diodes, thyristors, transistors, IC and relays against transient Voltages. S imilar protection of many types of measuring instruments, control machinery and communication equipment and broadcasting equipment against inductive lightning and switching surges. Protection of general purpose electrical equipment, domestic mechinery and appliances. TV and radios and similar consumer products against lightning and switching surges. Line and groud circuit Varistor voltage selection table(ZE) Power Supply Voltage 100V AC 200V AC Type SVC431D -□□A SVC471D -□□A SVC751D -□□A to SVC112D -□□A* SVC182D -□□A** Notes : ① When subjected to megger testing(500V DC), the insulation resistance value can decrease due to the leakage current of the SVC, To avoid this remove the varistor or use* marked SVC. ② When subjected to dielectric strength test(1000V AC). remove the SVC or use** marked SVC. Switching Circuit Protection Protection of relay (Contact coil) Protection of semiconductors ① Connect the SVC at a position nearer to the equipment than the overcurrent protection device “Ⅰ” (fuse, MCCB) as is shown in the diagram. When the SVC is shorted, the overcurrent protection device “Ⅰ” operates (trips or blow off the fuse). ② If the overcurrent protection device “Ⅰ” not be installed can in Ⅰ” “ position, connect a fuse at “Ⅱ” position. Select fuse rated current for the SVC referring to the following table. SVC Applicable fuse rated current(A) 05A 05B 1 to 2 07A 07B 2 to 3 10A 10B 3 to 5 14A 14B 3 to 10 20A 20B 5 to 15 DISC Ceramic Capacitors www.samwha.com Varistor voltage selection guide Power Supply Voltage 12V DC 24V DC 100V DC Type SVC220D -□□B SVC390D -□□B SVC151D -□□A SVC201D -□□A 100V AC SVC221D -□□A SVC241D -□□A SVC271D -□□A Notes : ① The power supply voltage must not exceed the maximum allowable circuit voltage of the SVC Power Supply Circuit Protection Line circuit Varistor voltage selection table (ZL) Power Supply Voltage Type SVC201D -□□A 100V AC SVC221D -□□A SVC241D -□□A SVC271D -□□A* SVC391D -□□A 200V AC 12V DC 24V DC Notes : ① The power supply voltage must not exceed the maximum allowable circuit voltage. ② Since independent wiring loads and capacitive loads cause the voltage build-up at the time of opening or closing the load, use SVC having a varistor voltage as high as possible.(*mark) ③ The bold faced portions of the type letters vary. SVC431D -□□A SVC471D -□□A* SVC220D -□□B SVC390D -□□B Select varistors taking a note of operating conditions peculiar to the equipment. ③ When“Z2”SVC is connected between the equipment and ground install an ELCB (Earth Leakage Circuit Breaker). If not possible, connect a fuse or thermal fuse at Ⅲ”position. “ Installation ① When operated at location near heating element or exposed to direct sun light, confirm that the ambient temparature range. ② When operated in dusty or dirty locations, or exposed to corrosive atomospheres, or where metallic powders or salt can be expected, be sure to mount within a protective enclosure. AC/DC single-phase circuit AC three-phase circuit Molding When shielding the SVC in a resin molding, take a note of the materials used and temperature, since they influence the reliability. For further information please contact SAMWHA Telecommunication Circuit Protection ② Pay due attention to the surge energy generated by the load. ③ Select SVC referring to the pulse lifetime rating. ④ To further reduce the tendency of sparking across the contacts connect a capacitors parallel with the SVC. This will also protect the equipment from electromagnetic wave jamming. Current, power and energy rating vs, temperature Application Notes Varistor voltage selection guied Power Supply Voltage 12V DC Type SVC180D -□□B SVC220D -□□B SVC820D -□□A 24V AC Notes : The varistor SVC has a capacitance value. Take not of this when applying them to high-frequency signal circuits. SVC390D -□□B SVC820D -□□A Overcurrent protection When surges exceed the rating for the SVC, short-circuits or damages can be expected. Take following precautions. AC/DC single-phase circuit AC three-phase circuit Electrical Characteristics Operating ambient temperature Storage temperature Voltage temperatur coefficient Insulation resistance(at500V) -40℃ to +85℃ -40℃ to +125℃ -0.05% ℃ Over 1000MΩ 128 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 129 SVC Varistors Type Recognized standards Standard Date Content Transient Voltage surge suppressors Protectors for data communication and fire alarm circuirt Varistor for Across - The - Line use as transient protection on 120Vac system Surge Suppression Applicable SVC series Cord connected and Direct UL 1449 04. 06. 02 Plug in Type Equipment Pemanently connected type equipment 05Series, 07Series, 10Series 14Series, 20Series 10Series, 14Series, 20Series E151195 File No. Contect Protection Microwave Oven UL UL 497B C22.2 NO.1-M 1981 VDE 02. 06 SVC 180D - □ ~SVC 821D -□ E154171 Thytister Protection Triac Protection DISC Ceramic Capacitors www.samwha.com CAS 04. 08. 02 02. 05. 16 02. 05. 16 99. 08. 25 94. 12. 15 250V AC SVC 201D - □ ~ SVC 182D -□ LR78923 4000153 40001516 116012 ID03/0294 SVC 180 - □ -SVC 112D -14 TV Booster Sound Output Circuit ISO 9001:2000 Application Exampel Fire Alarm System Stove, Boiler Varistor Terminology Varistor Voltage : Vnom Traffic Signal Control Vending Machine Clamping Voltage : Vc Maximum terminal voltage (peak voltage across the varistor) measured with an applied 8/20㎲ impulse of a given peak current. Varistor peak terminal voltage measured with a specified current applied The DC current applied is 1mA normally. Solenold Brake, Clutch 130 SAMWHA CAPACITOR Co., Ltd. DISC Ceramic Capacitors 131 Capacitance Typical values measured at a test frequency of 1kHz Test current waveform Characteristics tests for Varistors are carried out by using 8/20㎲ test impulses Data such as the maximum clamping voltage(Vc)and the transient peak current(Itm) are obtained by using this impulse current However, for the Vc characteristics of the Axial Package type a 10mA DC squarewave current is used to cary out the test. Rated peak transient current : itm Maximum peak current through the varistor with line voltage applied. The maximum peak current with in the varistor voltage change ratio of ±10% with the standard 8/20㎲ impulse current applied two times at 5 minute interval. Rated transient energy : Wtm Maximum allowable energy for a single impulse of 2ms square-wave current waveform with rated continuous voltage applied. Maximum energy rating base on a shift of Vnom of less than ±10% of initial value. DISC Ceramic Capacitors www.samwha.com Surface Mount Disc Capacitors Surface Mount Disc Capacitors 134 Rated RMS Voltage : Vacm Maximum continuous sinusoidal RMS voltage at 50/60Hz which may be applied. Rated DC Voltage : Vdcm Maximum continuous DC voltage which may be applied. Pulse lifetime rating This is expressed as the maximum allowable number of impulse currents applied. 8/20 ㎲ impulse current(or 2ms square wave) is applied at prescribed interval. This curve also provides for derating current as required with repetitive pulsing. Rated average power dissipation : Ptam Maximum average power that can be applied within the specified ambient temperature. 132 SAMWHA CAPACITOR Co., Ltd.