SCM1100M

1-2-6 High-voltage 3-phase Motor Driver IPMs SCM1100M Series Support for 3-shunt, Output Element : IGBT ■Features • Each half-bridge circuit consists of a pre-driver circuit that is completely independent from the others • Protection against simultaneous high- and low-side turning on • Bootstrap diodes with series resistors for suppressing inrush current are incorporated • CMOS compatible input (3.3 to 5 V) • Designed to minimize simultaneous current through both high- and low-side IGBTs by optimizing gate drive resistors • UVLO protection with auto restart • Overcurrent protection with off-time period adjustable by an external capacitor • Fault (FO indicator) signal output at protection activation: UVLO (low side only), OCP, and STP • Proprietary power DIP package • UL Recognized Component (File No.: E118037) ■Absolute Maximum Ratings Parameter Symbol SCM1101M (SCM1101MF) 450 500 600 20 20 10 20 –0.5 to +7 7 20.8(33.8) 6(3.7) 6.5(4.2) –20 to +100 150 –40 to +150 2000 SCM1103M 450 500 600 20 20 5 10 –0.5 to +7 7 19 6.3 6.5 –20 to +100 150 –40 to +150 2000 Ratings SCM1104M SCM1105MF (SCM1104MF) 450 450 500 500 600 600 20 20 20 20 8 15 16 30 –0.5 to +7 –0.5 to +7 7 7 20.2(32.9) 41.7 6.2(3.8) 3 6.5(4.2) 4 –20 to +100 –20 to +100 150 150 –40 to +150 –40 to +150 2000 2000 SCM1106M (SCM1106MF) 450 500 600 20 20 10 20 –0.5 to +7 7 20.8(33.8) 6(3.7) 6.5(4.2) –20 to +100 150 –40 to +150 2000 SCM1110MF 450 500 600 20 20 15 30 –0.5 to +7 7 41.7 3 4 –20 to +100 150 –40 to +150 2000 Unit V V V V V Adc Adc V V W °C/W °C/W °C °C °C V （Ta＝25℃） Conditions Between VBB and LS1 to LS3 Between VBB and LS1 to LS3 VCC=15V,IC=1mA,VIN=0V VCC1 to 3 and COM1 to COM3 VB1 to VB3 and HS (U,V,W) T≤1ms HIN1 to HIN3 or LIN1 to LIN3 and COM1 to COM3 FO1 to FO3 and COM1 to COM3 Tc=25°C while one IGBT element operates Per IGBT element Per FRD element Supply Voltage VBB Supply Voltage (Surge) VDC(Surge) IGBT Output Withstand Voltage VCES Control Supply Voltage VCC Control Supply Voltage (Bootstrap) VBS Output Current (continuous) Io Output Current (pulse) Iop Input Voltage VIN FO Pin Voltage VFO Power Dissipation PD Thermal Resistance (IGBT) R(j-c)Q Thermal Resistance (FRD) R(j-c)F Operating Case Temperature TOP Junction Temperature Tj Storage Temperature Tstg Insulation Withstand Voltage Viso Between rear and lead pins, AC one minute ■Recommended Operating Conditions Parameter Main Supply Voltage Control Supply Voltage Minimum Input Pulse Width Input Signal Dead Time FO Pull-up Resistor CFO Capacitor Capacity FO Pull-up Voltage Boot Capacitor Shunt Resistor*1 PWM Carrier Frequency Junction Temperature Symbol VDC VCC,VBS tINmin(on) tINmin(off) tdead RFO CFO VFO CBOOT RS fc Tj min. – 13.5 0.5 0.5 1.5 1 1 4.5 10 25.5 – – Ratings SCM1100M Series typ. 300 – – – – – – – – – – – Unit max. 400 16.5 – – – 22 10 5.5 220 – 20*2 125 V V µs µs µs kΩ nF V uF mΩ kHz °C Conditions Between VBB and LS ON pulse OFF pulse For Ip≤rated output current (pulse) *1: The shunt resistance varies depending on the rated current. *2: 10 for SCM1101M(F)/SCM1015MF 144 ICs SCM1100M Series ■Electrical Characteristics Parameter Control Supply Voltage Control Supply Current Bootstrap Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Hold Time Blanking Time IGBT Output Withstand Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Boot Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Recovery Time Boot Diode Series Resistance Symbol VCC ICC Ibs VIH VIL VH IIH IIL VUVHL VUVHH VUVLL VUVLH VFOL VFOH VTRIP tP tbk VCES ICES VCE(sat) VF IIB VFB trr RB td(on) tr trr td(off) tf td(on) tr trr td(off) tf SCM1101M/SCM1101MF min. typ. max. 13.5 – 16.5 – 5 8 – 400 800 – 2 2.5 1 1.5 – – 0.5 – – 50 100 – – 2 10 – 12 10.5 – 12.5 10.5 – 12.5 11 – 13 – – 0.5 4.8 – – 0.46 0.5 0.54 2 – – – 2 – 600 – – – – 1 – 1.75 2.2 – 1.7 2.2 – 5 10 – 1.1 1.3 – 70 – 17.6 22 26.4 – 320 – – 50 – – 80 – – 560 – – 210 – – 350 – – 80 – – 140 – – 610 – – 200 – min. 13.5 – – – 1 – – – 10 10.5 10.5 11 – 4.8 0.46 2 – 600 – – – – – – 17.6 – – – – – – – – – – Ratings SCM1103M typ. – 5 400 2 1.5 0.5 50 – – – – – – – 0.5 – 2 – – 1.7 1.4 5 1.1 70 22 340 60 80 430 240 380 90 100 500 220 max. 16.5 8 800 2.5 – – 100 2 12 12.5 12.5 13 0.5 – 0.54 – – – 1 2.1 2 10 1.3 – 26.4 – – – – – – – – – – SCM1104M/SCM1104MF min. typ. max. 13.5 – 16.5 – 5 8 – 400 800 – 2 2.5 1 1.5 – – 0.5 – – 50 100 – – 2 10 – 12 10.5 – 12.5 10.5 – 12.5 11 – 13 – – 0.5 4.8 – – 0.46 0.5 0.54 2 – – – 2 – 600 – – – – 1 – 1.75 2.2 – 1.6 2.2 – 5 10 – 1.1 1.3 – 70 – 17.6 22 26.4 – 360 – – 70 – – 80 – – 560 – – 210 – – 420 – – 110 – – 140 – – 630 – – 210 – Unit V mA uA V Conditions Between VCC and COM VCC=15V, 3 circuits total VB-HS=15V, 1 circuit VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, VIN=5V VCC=15V, VIN=0V VCC=15V µA V V V ms µs V mA V V µA V ns Ω VCC=15V,VFO=5V RFO=10kΩ VCC=15V VCC=15V, CFO=2.2nF VCC=15V VCC=15V, IC=1mA, VIN=0V VCC=15V, VCE=600V, VIN=0V VCC=15V, IC=rated output current (continuous) VIN=5V VCC=15V, IF=rated output current (continuous), VIN=0V VR=600V IF=0.15A IF/IRP=100mA/100mA VDC=300V, V CC=15V IC=10A(SCM1101M), IC=5A(SCM1103M), IC=8A(SCM1104M) HIN=0 to 5V Inductive load VDC=300V, V CC=15V IC=10A(SCM1101M), IC=5A(SCM1103M), IC=8A(SCM1104M) HIN=0 to 5V Inductive load High Side Switching Time ns Low Side Switching Time ns Parameter Control Supply Voltage Control Supply Current Bootstrap Supply Current Input Voltage Input Voltage Hysteresis Width Input Current Undervoltage Lock Out (high side) Undervoltage Lock Out (low side) FO Pin Output Voltage Overcurrent Protection Trip Voltage Overcurrent Protection Hold Time Blanking Time IGBT Output Withstand Voltage IGBT Output Leakage Current IGBT Output Saturation Voltage Boot Diode Forward Voltage Boot Diode Leakage Current Boot Diode Forward Voltage Boot Diode Recovery Time Boot Diode Series Resistance Symbol VCC ICC Ibs VIH VIL VH IIH IIL VUVHL VUVHH VUVLL VUVLH VFOL VFOH VTRIP tP tbk VCES ICES VCE(sat) VF IIB VFB trr RB td(on) tr trr td(off) tf td(on) tr trr td(off) tf min. 13.5 – – – 1 – – – 10 10.5 10.5 11 – 4.8 0.46 2 – 600 – – – – – – 17.6 – – – – – – – – – – High Side Switching Time Low Side Switching Time SCM1105MF typ. – 5 400 2 1.5 0.5 50 – – – – – – – 0.5 – 2 – – 1.75 1.75 5 1.1 70 22 365 80 90 690 200 415 135 115 790 205 max. 16.5 8 800 2.5 – – 100 2 12 12.5 12.5 13 0.5 – 0.54 – – – 1 2.2 2.2 10 1.3 – 26.4 – – – – – – – – – – Ratings SCM1106M/SCM1106MF min. typ. max. 13.5 – 16.5 – 5 8 – 400 800 – 2 2.5 1 1.5 – – 0.5 – – 50 100 – – 2 10 – 12 10.5 – 12.5 10.5 – 12.5 11 – 13 – – 0.5 4.8 – – 0.46 0.5 0.54 2 – – – 2 – 600 – – – – 1 – 2.2 2.6 – 1.7 2.2 – 5 10 – 1.1 1.3 – 70 – 17.6 22 26.4 – 320 – – 50 – – 80 – – 490 – – 80 – – 350 – – 80 – – 140 – – 540 – – 80 – min. 13.5 – – – 1 – – – 10 10.5 10.5 11 – 4.8 0.46 2 – 600 – – – – – – 17.6 – – – – – – – – – – SCM1110MF typ. – 5 400 2 1.5 0.5 50 – – – – – – – 0.5 – 2 – – 2.2 1.75 5 1.1 70 22 365 80 90 650 85 415 135 115 755 85 Unit max. 16.5 8 800 2.5 – – 100 2 12 12.5 12.5 13 0.5 – 0.54 – – – 1 2.6 2.2 10 1.3 – 26.4 – – – – – – – – – – V mA uA V Conditions Between VCC and COM VCC=15V, 3 circuits total VB-HS=15V, 1 circuit VCC=15V, Output:ON VCC=15V, Output:OFF VCC=15V VCC=15V, VIN=5V VCC=15V, VIN=0V VCC=15V µA V V V ms µs V mA V V µA V ns Ω VCC=15V, VFO=5V RFO=10kΩ VCC=15V VCC=15V,CFO=2.2nF VCC=15V VCC=15V, IC=1mA, VIN=0V VCC=15V, VCE=600V, VIN=0V VCC=15V, IC=rated output current (continuous) VIN=5V VCC=15V, IF=rated output current (continuous), VIN=0V VR=600V IF=0.15A IF/IRP=100mA/100mA VDC=300V, VCC=15V IC=15A(SCM1105M), IC=10A(SCM1106M), IC=15A(SCM1110MF) HIN=0 to 5V Inductive load VDC=300V, VCC=15V IC=15A(SCM1105M), IC=10A(SCM1106M), IC=15A(SCM1110MF) HIN=0 to 5V Inductive load ns ns ICs 145 1-2-6 High-voltage 3-phase Motor Driver ICs ■Internal Block Diagram (Single Circuit) HS VB VB VBB VCC VCC HIN LIN UV Detect Input Logic & Shoot Through Prevention Level Shift HO HIN LIN Drive Corcuit HS U,V,W UV Detect O.C. Protect COM FO CFO COM FO CFO Drive Corcuit LD LS LS HVIC ■Typical Connection Diagram 8 7 CBOOT 6 VCC HIN LIN Input Logic & Shoot Through Prevention VB UV Detect Level Shift HO Drive Circuit SCM1100M 31 5 3 32 HS The input pulldown resistor is built in IC (about 100 kΩ). However, if the input is expected to be unstable or very fluctuant, it needs to be reinforced with external resistor. Attach capacitors near IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated. UV Detect O.C. Protect 4 1 2 16 15 CBOOT 14 13 Controller COM FO CFO Drive Circuit LO 33 LS HVIC1 28 VB UV Detect Input Logic & Shoot Through Prevention Level Shift Drive Circuit 29 HS UV Detect O.C. Protect M VCC HIN LIN HO 11 12 9 10 24 23 CBOOT 22 21 19 VFO RFO 20 17 18 CN VCC COM FO CFO Drive Circuit LO 30 LS HVIC2 25 VB VCC HIN LIN Input Logic & Shoot Through Prevention UV Detect Level Shift Drive Circuit 26 HS UV Detect O.C. Protect HO COM FO CFO Drive Circuit LO 27 LS HVIC3 RS VBB CFO 146 ICs SCM1100M Series ■External Dimensions (SCM) (Unit : mm) Pitch tolerance by the lead root size: ±0.1 (lead center) Planar state diagram Root (lead center) JAPAN Part No. Lot No. (lead center) (lead center) (lead center) Pitch tolerance by the lead root size: ±0.1 (lead center) C lead cross-section (S=9) B lead cross-section (S=9) A lead cross-section (S=9) D lead cross-section (S=9) (Size after solder dip) Without Fin (SCM1100M) Forming No. 2551 Product Mass: Approx. 12.6g Pitch tolerance by the lead root size: ±0.1 (lead center) Planar state diagram Root (lead center) JAPAN Part No. Lot No. (lead center) (lead center) (lead center) Pitch tolerance by the lead root size: ±0.1 (lead center) C lead cross-section (S=9) B lead cross-section (S=9) A lead cross-section (S=9) D lead cross-section (S=9) (Size after solder dip) With Fin (SCM1100MF) Forming No. 2552 Product Mass: Approx. 13.5g ICs 147