2SK3293

Ordering number:ENN6345 N-Channel Silicon MOSFET 2SK3293 Ultrahigh-Speed Switching Applications Features · Low ON resistance. · Ultrahigh-speed switching. · 4V drive. Package Dimensions unit:mm 2062A [2SK3293] 4.5 1.6 1.5 0.5 3 1.5 2 3.0 0.75 1 1.0 0.4 2.5 4.25max 0.4 Specifications Absolute Maximum Ratings at Ta = 25˚C Parameter Drain-to-Source Voltage Gate-to-Source Voltage Drain Current (DC) Drain Current (Pulse) Allowable Power Dissipation Channel Temperature Storage Temperature Symbol VDSS VGSS ID IDP PD Tch Tstg PW≤10µs, duty cycle≤1% Mounted on a ceramic board (250mm2×0.8mm) Tc=25˚C 1 : Gate 2 : Drain 3 : Source SANYO : PCP (Bottom view) Conditions Ratings 60 ±20 3 12 1.5 3.5 150 –55 to +150 Unit V V A A W W ˚C ˚C Electrical Characteristics at Ta = 25˚C Parameter Drain-to-Source Breakdown Voltage Zero Gate Voltage Drain Current Gate-to-Source Leakage Current Cutoff Voltage Forward Transfer Admittance Static Drain-to-Source On-State Resistance Symbol V(BR)DSS IDSS IGSS VGS(off) | yfs | RDS(on)1 RDS(on)2 ID=1mA, VGS=0 VDS=60V, VGS=0 VGS=±16V, VDS=0 VDS=10V, ID=1mA VDS=10V, ID=1.5A ID=1.5A, VGS=10V ID=1A, VGS=4V Conditions Ratings min 60 10 ±10 1.0 2.6 3.6 115 150 150 210 2.4 typ max Unit V µA µA V S mΩ mΩ Marking : KZ Continued on next page. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 60800TS (KOTO) TA-2737 No.6345–1/4 2SK3293 Continued from preceding page. Parameter Input Capacitance Output Capacitance Reverse Transfer Capacitance Turn-ON Delay Time Rise Time Turn-OFF Delay Time Fall Time Total Gate Charge Gate-to-Source Charge Gate-to-Drain "Miller" Charge Diode Forward Voltage Symbol Ciss Coss Crss td(on) tr td(off) tf Qg Qgs Qgd VSD IS=3A, VGS=0 VDS=10V, VGS=10V, ID=3A VDS=20V, f=1MHz VDS=20V, f=1MHz VDS=20V, f=1MHz See specified Test Circuit See specified Test Circuit See specified Test Circuit See specified Test Circuit Conditions Ratings min typ 220 75 25 7 8 30 29 8.6 1.3 1.8 0.83 1.2 max Unit pF pF pF ns ns ns ns nC nC nC V Switching Time Test Circuit VIN 10V 0V VIN PW=10µs D.C.≤1% VDD=30V ID=1.5A RL=20Ω D G VOUT P.G 50Ω 2SK3293 S 6.0V 8.0V V 3.5 ID -- VDS V 5.0 6 ID -- VGS VDS=10V V 3.0 10.0 4.0 3.5 V 5 Drain Current, ID – A 2.5 3 Drain Current, ID – A .0V 4 2.0 3 Tc= 1.0 0.5 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 1 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 IT01458 Drain-to-Source Voltage, VDS – V 250 IT01457 Gate-to-Source Voltage, VGS – V 300 RDS(on) -- VGS Tc=25°C RDS(on) -- Tc Static Drain-to-Source On-State Resistance, RDS(on) – mΩ Static Drain-to-Source On-State Resistance, RDS(on) – mΩ 200 ID=1.5A 1.0A 250 200 150 150 I D= , VG 1.0A 4V S= 100 1. I D= 100 =10 VGS 5A, V 50 50 0 0 2 4 6 8 10 12 14 16 18 20 0 --60 --25 °C 140 25° 100 120 160 IT01460 --40 --20 Gate-to-Source Voltage, VGS – V IT01459 Case Temperature, Tc – °C 0 20 40 60 80 No.6345–2/4 C VGS=2.5V 2 75° C 1.5 2SK3293 Forward Transfer Admittance, | yfs | – S 10 7 5 3 2 1.0 7 5 3 2 0.1 7 5 3 2 0.01 0.001 2 3 5 7 0.01 2 3 5 7 0.1 23 5 7 1.0 23 5 7 10 IT01461 1000 yfs -- ID VDS=10V 10 7 5 3 2 1.0 7 5 3 2 0.1 7 5 3 2 IF -- VSD VGS=0 = Tc --2 C 5° 7 C 5° °C 25 Forward Current, IF – A 75° C 25°C 0.6 0.01 0.3 0.4 0.5 --25° C 0.7 0.8 Tc= 0.9 1.0 IT01462 Drain Current, ID – A 100 7 Diode Forward Voltage, VSD – V SW Time -- ID tf Ciss, Coss, Crss -- VDS f=1MHz 7 5 Switching Time, SW Time – ns 5 Ciss, Coss, Crss – pF 3 2 3 2 Ciss tr 10 7 5 3 2 td(off) 100 7 5 3 td(on) Coss 1.0 0.1 VDD=30V VGS=10V 2 3 5 7 1.0 2 3 5 2 Crss 10 0 10 20 30 40 50 60 IT01464 Drain Current, ID – A 10 9 8 10 IT01463 100 7 5 3 2 7 Drain-to-Source Voltage,VDS – V VGS -- Qg VDS=10V ID=3A Drain Current, ID – A ASO 10 0µ s Gate-to-Source Voltage, VGS – V IDP=12A ID=3A DC 10µs 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 10 7 5 3 2 1.0 7 5 3 2 0.1 7 5 3 2 1m s 10 10 op era ms 0m Operation in this area is limited by RDS(on). s tio n Total Gate Charge, Qg – nC 2.0 0.01 0.1 Tc=25˚C 1pulse 2 3 5 7 1.0 2 3 5 7 10 2 3 IT01465 4.0 Drain-to-Source Voltage,VDS – V 5 7 100 IT01466 PD -- Ta Allowable Power Dissipation, PD – W PD -- Tc Allowable Power Dissipation, PD – W 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1.5 M ou nte do na 1.0 ce ram ic bo ard (2 50 0.5 mm 2 ×0 .8m m) 140 160 0 0 20 Ambient Temperature, Ta – °C 40 60 80 100 120 0 20 40 IT01468 Case Temperature, Tc – °C 60 80 100 120 140 160 IT01467 No.6345–3/4 2SK3293 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of June, 2000. Specifications and information herein are subject to change without notice. PS No.6345–4/4