FTS1003

Ordering number:ENN6154A P-Channel Silicon MOSFET FTS1003 Load Switching Applications Features · Low ON resistance. · 2.5V drive. · Mounting height 1.1mm. Package Dimensions unit:mm 2147A [FTS1003] 0.65 8 5 0.5 0.95 3.0 0.425 1 4 0.25 (0.95) 1 : Drain 2 : Source 3 : Source 4 : Gate 5 : Drain 6 : Source 7 : Source 0.125 8 : Drain SANYO : TSSOP8 4.5 Specifications Absolute Maximum Ratings at Ta = 25˚C Parameter Drain-to-Source Voltage Gate-to-Source Voltage Drain Current (DC) Drain Current (pulse) Allowable Power Dissipation Channel Temperature Storage Temperature Symbol VDSS VGSS ID IDP PD Tch Tstg PW≤10µs, duty cycle≤1% Conditions 6.4 Ratings –20 ±10 –3 –15 1.3 150 –55 to +150 Unit V V A A W ˚C ˚C Mounted on a ceramic board (1000mm2×0.8mm) Electrical Characteristics at Ta = 25˚C Parameter Drain-to-Source Breakdown Voltage Zero-Gate Voltage Drain Current Gate-to-Source Leakage Current Cutoff Voltage Forward Transfer Admittance Static Drain-to-Source On-State Resistance Input Capacitance Output Capacitance Reverse Transfer Capacitance Symbol V(BR)DSS IDSS IGSS VGS(off) | yfs | RDS(on)1 RDS(on)2 Ciss Coss Crss ID=–1mA, VGS=0 VDS=–20V, VGS=0 VGS=±8V, VDS=0 VDS=–10V, ID=–1mA VDS=–10V, ID=–3A ID=–3A, VGS=–4V ID=–1A, VGS=–2.5V VDS=–10V, f=1MHz VDS=–10V, f=1MHz VDS=–10V, f=1MHz –0.4 5 8 70 105 600 300 150 90 144 Conditions Ratings min –20 –10 ±10 –1.4 typ max Unit V µA µA V S mΩ mΩ pF pF pF Marking : S1003 Continued on next page. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 30100TS (KOTO) TA-2125 No.6154-1/4 FTS1003 Continued from preceding page. Parameter Turn-ON Delay Time Rise Time Turn-OFF Delay Time Fall Time Total Gate Charge Gate-to-Source Charge Gate-to-Drain "Miller" Charge Diode Forward Voltage Symbol td(on) tr td(off) tf Qg Qgs Qgd VSD Conditions See specified Test Circuit See specified Test Circuit See specified Test Circuit See specified Test Circuit VDS=–10V, VGS=–10V, ID=–3A VDS=–10V, VGS=–10V, ID=–3A VDS=–10V, VGS=–10V, ID=–3A IS=–3A, VGS=0 Ratings min typ 15 140 80 85 24 3 6 –1.0 –1.5 max Unit ns ns ns ns nC nC nC V Switching Time Test Circuit 0V –4V VIN VDD=–10V ID=–3A RL=3.3Ω D VOUT VIN PW=10µs D.C.≤1% G FTS1003 P.G 50Ω S -3.5 ID - VDS -6V -5V -4V -6 ID - VGS VDS=-10V -2 -3.0 V -5 Drain Current, ID – A -8V -2.5 Drain Current, ID – A -2.0 -2.5V -3V -3.5V -4 -3 0 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 0 0 -0.5 -1.0 75 -1.5 Ta -0.5 °C -1 =-2.0 25° -1.0 VGS=-1.5V -2 25° C C -1.5 -2.5 Drain-to-Source Voltage, VDS – V 100 7 5 3 2 10 7 5 3 2 1.0 7 5 3 2 0.1 -0.01 2 3 5 7 -0.1 2 3 5 7 -1.0 2 3 5 7 -10 Gate-to-Source Voltage, VGS – V 200 180 160 140 120 100 80 60 40 20 0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 | yf s | - I D VDS=-10V R DS(on) - VGS Ta=25°C ID=-3A ID=-1A Forward Transfer Admittance, | yfs | – S °C -25 Ta= 25°C °C 75 Drain Current, ID – A Static Drain-to-Source On-State Resistance, RDS(on) – mΩ Gate-to-Source Voltage, VGS – V No.6154-2/4 FTS1003 200 180 R DS(on) - Ta -10 7 5 3 I F - VSD VGS=0 Static Drain-to-Source On-State Resistance, RDS (on) – mΩ 160 140 120 100 80 60 40 20 0 -60 -40 -20 0 20 40 60 80 100 120 140 160 -1A I D= .5V =-2 VGS , =-4V VGS Forward Current, IF – A 2 -1.0 7 5 3 2 -0.1 7 5 3 2 3A, I D=- -0.01 0 -0.2 -0.4 Ta=75 -0.6 °C 25°C -25°C -0.8 -1.0 -1.2 -1.4 Ambient Temperature, Ta – ˚C 10000 7 5 3 2 1000 7 5 3 2 100 7 5 3 2 10 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 Diode Forward Voltage, VSD – V -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 0 2 4 6 8 10 12 14 16 18 20 22 24 Ciss,Coss,Crss - VDS f=1MHz Gate-to-Source Voltage, VGS – V VGS - Q g VDS=-10V ID =-3A Ciss, Coss, Crss – pF Ciss Coss Crss Drain-to-Source Voltage, VDS – V Total Gate Charge, Qg – nC SW Time - I D 1000 7 5 ASO 3 2 -10 7 5 VDD =-10V VGS=-4V IDP=-15A Switching Time, SW Time – ns 100 7 5 3 2 10 7 5 3 2 1.0 7 -0.1 2 3 5 td(off) Drain Current, ID – A 3 2 100µs 1m s ID=-3A DC tr tf 10 10 0m s era tio 3 2 -1.0 7 5 3 2 -0.1 7 5 3 2 ms op td(on) Operation in this area is limited by RDS(on). n 7 -1.0 2 3 5 7 -10 -0.01 -0.01 2 3 Ta=25°C Single pulse Mounted on a ceramic board (1000mm2×0.8mm) 5 7-0.1 23 5 7 -1.0 23 5 7 -10 23 Drain Current, ID – A 1.6 Drain-to-Source Voltage, VDS – V P D - Ta Allowable Power Dissipation, PD – W 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 M ou nt ed on ac er am ic bo ar d( 10 00 m m2 ×0 .8m m ) 160 0 20 40 60 80 100 120 140 Ambient Temperature, Ta – ˚C No.6154-3/4 FTS1003 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of March, 2000. Specifications and information herein are subject to change without notice. PS No.6154-4/4