LA42031

Ordering number : ENA0394 Monolithic Linear IC LA42031 Overview Audio Output for TV application 5W Monaural Power Amplifier LA42031 is 5W monaural AF power amplifier intended for televisions. Functions • 3W Monaural (VCC = 9V, RL = 8Ω, THD = 10%). • 5W Monaural (VCC = 11V, RL = 8Ω, THD = 10%). • Built-in standby function. • Built-in mute function. • Built-in various protection circuit (short to VCC/short to groumd/load shorting/overheating). Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Maximum junction temperature Thermal resistance Operating temperature Storage temperature Symbol VCC max Pd max Tj max θjc Topr Tstg No signal Infinitely large heat sink Conditions Ratings 16 15 150 3 -25 to +75 -40 to +150 Unit V W °C °C/W °C °C Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Recommended load resistance Allowable operating supply voltage range Symbol VCC RL VCC op Conditions Ratings 9 8 5.5 to 15 Unit V Ω V Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 40407 MS PC 20060404-S00009 No.A0394-1/7 LA42031 Electrical Characteristics at Ta = 25°C, VCC = 9V, RL = 8Ω, f = 1kHz, Rg = 600Ω Parameter Standby current Quiescent current Output power Symbol Ist ICCO PO1 PO2 Total harmonic distortion Voltage gain Output noise voltage Ripple rejection ratio Mute attenuation value Mute control voltage (pin 6) THD VG VNO SVRR ATT Vmute Amplifier OFF Rg = 0, RL = OPEN THD = 10% VCC = 11V, THD = 10% PO = 1W VO = 0dBm Rg = 0, BPF = 20Hz to 20kHz Rg = 0, fR = 100Hz, VCCR = 0dBm VO = 1Vrms, BPF = 20Hz to 20kHz Mute ON *1 Mute OFF Standby control voltage (pin 5) Vst Amplifier ON *1 Amplifier OFF Input resistance Ri 40 80 1.7 0 2.5 0 21 30 33 25 2 Conditions min Ratings typ 0 45 3 5 0.06 35 0.2 50 90 3.0 0.5 15 0.5 39 0.2 37 0.4 max 10 90 μA mA W W % dB mVrms dB dB V V V V kΩ Unit *1 : Note that the STANDBY pin (pin 5) and MUTE pin (pin 6) incorporate the anti-static diode and that decrease of the VCC 7 pin potential below that of pin 5/6 causes the current to flow through the diode. Package Dimensions unit : mm (typ) 3107B 18 Pd max -- Ta Infinitely large heat sink 15 25.6 C0.7 3.4 (10.0) ( 2.0) 2.4 Allowable power dissipation, Pd max – W 16 14 12 10 8 6 4 2 0 --20 3.0 min 100×100×1.5mm3 11.7 θjc=3ºC/W 11.2 (11.8) 15.4max (13.9) 50×50×1.5mm3 5.8 4.5 1 0.5 2.0 (0.8) 1.15 13 1.0 min No heat sink 0.4 1.2 0 20 40 60 80 100 120 140 160 Ambient temperature, Ta – ˚C SANYO : SIP13H No.A0394-2/7 LA42031 Block Diagram Standby 5 VCC 7 MUTE 6 VCC/ground shorting protection circuit Load shorting protection circuit Thermal protection circuit PWR 10 GND PRE GND 3 8 IN 4 Ri= 30kΩ Input amplifier Output amplifier 9 +OUT2 -OUT2 1 Ripple Filter Test Circuit LA42031 Ripple Filter 1 C2 + 47μF /16V PRE GND 3 PWR GND 10 N.C. 2 IN 4 STBY MUTE 5 6 VCC +OUT -OUT 9 N.C. 11 N.C. 12 N.C. 13 * C1 4.7μF /10V C3 10μF /10V R1 15kΩ + 7 8 C4 1000μF /16V + RL C5 0.1μF R4 2.2Ω C6 0.1μF R5 2.2Ω +5V * LA42031 employs the zero-bias type input circuit, with the input pin potential being nearly zero (about 0.01V). Accordingly, the polarity must be determined according to the DC potential of a circuit connected to the previous stage of LA42031. No.A0394-3/7 LA42031 External Components C1 : The input coupling capacitors, for which 4.7μF or less is recommended. LA42031 employs the zero-bias type input circuit, with the input pin potential being nearly zero (about 0.01V). Accordingly, the polarity must be determined according to the DC potential of a circuit connected to the previous stage of LA42031. : Capacitor for starting time of the ripple filter and amplifier, for which 47μF is recommended. : Capacitor and resistor for mute. C3 is necessary even when the mute function is not used. : Power capacitor. : Capacitor and resistor for oscillation prevention. For C5, C6, the polyester film capacitor with superior temperature characteristics (Mylar capacitor) is recommended. Use R2, R3 of 2.2Ω along with the capacitor. C2 C3, R1 C4 C5, C6 R2, R3 1. Mute function (pin 6) With the pin 6 voltage of 1.7V (minimum) or more, the mute function is turned ON. Set the VM application voltage so that the pin 6 voltage becomes. 1.7V or more. The mute time constant is determined by R1 and C3. Determine the constant after careful review because it is related to the pop sound at mute ON/OFF. C3 is necessary even when the mute function is not used because it is related to the pop sound when the amplifier is turned ON. Note that the MUTE pin (pin 6) incorporates the anti-static diodo and that decrease of the VCC pin 7 potential below that of pin 6 causes the current to flow through the diode. Mute VCC VM R1 6 C3 + 10μF 2kΩ 20kΩ 2kΩ 2. Standby function (pin 5) The amplifier is turned ON when the voltage of 2.5V (minimum) or more is applied to pin 5. Pin 5 control voltage Pin 5 voltage 0 to 0.5 2.5 to 15 Amplifier OFF ON Standby ON OFF Standby VCC 2VBE VS RSTB 5 15kΩ 30kΩ To suppress the inrush current to pin 5 when the VSTB application voltage is high, insert the control resistor (RSTB). Example : Tosuppress the pin 5 inrush current to 500μA or less RSTB = Applied voltage (VSTB) -2VBE (About 1.4V) -15kΩ 500μA 1.5kΩ Note that the standby pin (pin 5) incorporates the anti-electrostatic diode, allowing the cu orrent to flow through the diode when the potential of VCC pin 7 decreases below that of pin 5. No.A0394-4/7 LA42031 Cautions for us 1. Short-circuit (power-output short-circuit), ground fault (GND-output short-circuit), and load short-circuit protective circuits are incorporated. They are activated in case of abnormal connection. These circuits remain active while such abnormal connection continues and is reset automatically when the abnormality is removed. In certain conditions, the protective circuits may be locked and continue to be active even when the abnormality is removed. In this case, either enter the standby mode or turn OFF the power supply. 2. The thermal protection circuit is incorporated and is activated when the junction temperature (Tj) rises to about 160°C or more. The output is controlled to return gradually to the attenuated state. 3. When the product is used near the maximum rating, even the slightest change in the condition may cause exceeding of the maximum rating, resulting possibly in breakdown. Take the sufficient margin for the supply voltage, etc. and always use the product within a range never exceeding the maximum rating. No.A0394-5/7 LA42031 60 ICCO – VCC RL = open Rg = 0Ω Output power, PO – W 12 Quiescent current, ICCO – A 50 10 Rg = 600Ω f = 1kHz THD = 10% PO – VCC 40 8 30 6 20 4 10 2 0 0 2 4 6 8 10 12 14 16 0 4 6 8 10 12 14 16 Supply voltage, VCC – V 1.5 7 5 3 2 0.1 7 5 3 2 0.1 7 5 3 2 0.01 0.1 2 3 5 7 2 3 5 7 THD – PO Supply voltage, VCC – V 1.5 7 5 3 2 0.1 7 5 3 2 0.1 7 5 3 2 0.01 23 5 7 100 23 5 7 1k 23 5 7 10k 23 5 7100k THD – f Total harmonic distortion, THD – % 10kHz 100Hz 1kHz 1 10 Total harmonic distortion, THD – % VCC = 9V RL = 8Ω Rg = 600Ω VCC = 9V RL = 8Ω Rg = 600Ω PO = 1W 10 Output power, PO – W 2 Frequency, f – Hz 0.4 Response – f VNO – Rg VCC = 9V RL = 8Ω DIN AUDIO 0 Output noise voltage, VNO – mVrms 23 5 7 1k 23 5 7 10k 23 5 7100k 0.3 Response – dB –2 –4 0.2 –6 0.1 –8 – 10 VCC = 14V RL = 8Ω Rg = 600Ω VO = 0dBm 23 5 7 100 10 0 100 2 3 Frequency, f – Hz 0 Resistance for signal generation, Rg – Ω 5 7 1k 2 3 5 7 10k 2 3 5 7 100k Mute Pin – ATT Ripple rejection ratio, SVRR – dB Mute attenuation value, Mute ATT – dB VCC = 9V RL = 8Ω DIN AUDIO 0 – 10 – 20 – 20 RL = 8Ω Rg = 0 fr = 100Hz VR = 0dBm CVCC = 0.1μF SVRR – VCC – 40 – 30 – 60 – 40 – 50 – 80 – 60 – 70 – 100 0.5 0.7 0.9 1.1 1.3 1.5 1.7 4 6 8 10 12 14 16 Mute contorol voltage, Vmute – V Supply voltage, VCC – V No.A0394-6/7 LA42031 0 SVRR – fr Ripple rejection ratio, SVRR – dB Ripple rejection ratio, SVRR – dB – 10 – 20 VCC = 9V RL = 8Ω Rg = 0 VR = 0dBm CVCC = 0.1μF 0 – 10 SVRR – VCCR VCC = 9V SVRR = 20log (VO/VCCR) RL = 8Ω Rg = 0 fR = 100Hz CVCC = 0.1μF – 20 – 30 – 30 – 40 – 40 – 50 – 50 – 60 – 70 10 23 5 7 100 23 5 7 1k 23 5 7 10k 23 5 7100k – 60 – 70 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 Ripple frequency, fr – Hz 5 Pd – PO VCC = 9V Rg = 600Ω f = 1kHz VCCR– Vrms Allowable power dissipation, Pd – W 4 3 2 1 0 0.1 2 3 5 7 1 2 3 5 7 10 Output power, PO – W SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of April, 2007. Specifications and information herein are subject to change without notice. PS No.A0394-7/7