LA4592W

Ordering number : EN5662 Monolithic Linear IC LA4592W 1.5-V Preamplifier + Power Amplifier for Headphone Stereo Products Overview The LA4592W is a single-chip 1.5-V headphone stereo system IC. The LA4592W adds a variety of functions, including a switch amplifier (for end product audio quality switches, the metal tape switch, and other switches) and an AMSS (Automatic Music Search System) function that supports blank skipping, to the earlier LA4590W. Furthermore, the LA4592W provides even lower no-signal time power levels for lower end-product power dissipation. In combination with the LA3235W 1.5-V record preamplifier IC, the LA4592W can be used to implement a record/playback cassette system with just two ICs. functions. • Ripple filter • Low boost function (BTL operation in the lowfrequency region) • Inter-track detection function (Supports AMSS and blank skipping) • Two switching amplifiers • Power switch (standby function) Features • Virtual ground impedance is reduced by built-in VREF amplifier • No capacitor required for ripple filter oscillation prevention. • Provides ample output power at low frequencies. (PO = 24 mW, VCC = 1.2 V, f = 150 Hz) • High-frequency cutoff capacitors built into the preamplifier and power amplifier inputs to minimize buzzing. Functions • Stereo preamplifier: supports auto reverse and includes a muting function. • Stereo power amplifier: Includes OCL and muting Package Dimensions Allowable power dissipation, Pd max – W unit: mm 3163A-SQFP48 [LA4592W] Ambient temperature, Ta – °C Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Operating temperature Storage temperature Symbol VCC max Pd max Topr Tstg Conditions SANYO: SQFP48 Ratings 3.0 320 –10 to +60 –40 to +125 Unit V mW °C °C Allowable Operating Ranges at Ta = 25°C Parameter Recommended supply voltage Operating supply voltage range Symbol VCC VCCop Conditions Ratings 1.5 0.95 to 2.2 Unit V V SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 73097HA (OT) No. 5662-1/5 LA4592W Operating Characteristics at Ta = 25°C, VCC = 1.2 V, f = 1 kHz, 0.775 V = 0 dB, RL = 10 kΩ (preamplifier) RL = 16 Ω (power amplifier) Parameter [PRE + PWR] Quiescent current Voltage gain (closed loop) [PRE AMP] Voltage gain (open loop) Voltage gain (closed loop) Maximum output voltage Total harmonic distortion Equivalent input noise voltage Interchannel crosstalk F/R crosstalk Ripple rejection ratio Muting output voltage [Low Boost + Power Amplifier] Voltage gain (closed loop) VG3 VG4 VG5 VG6 PO1 PO2 THD2 CT3 VNO Rr2 VM2 Ri ∆VG3 Rr3 VRF fr = 100 Hz, Vr = –30 dBm, VCC = 1.0 V, IRF = 25 mA, using a rank 6 2SB1295 VCC = 1.0 V, IRF = 25 mA VO = –20 dBm VO = –20 dBm, L.B = ON VO = –20 dBm, L.B = ON, f = 10 kHz VO = –20 dBm, L.B = ON, f = 100 Hz THD = 10 % THD = 10 %, f = 100 Hz, L.B = ON PO = 1 mW VO = –20 dBm, RV = 0 Ω RV = 0 Ω, BPF = 20 Hz to 20 kHz RV = 0 Ω, Vr = –30 dBm, fr = 100 Hz, TUNE 100 Hz VIN = –30 dBm, TUNE 1 kHz, With the muting function on 8 10 0 39 0.94 20.5 20.5 24.5 28 5 13 38 50 23 23 27.5 32 9 19 0.3 43 20 74 –90 12 1.5 25.5 25.5 30.5 36 dB dB dB dB mW mW % dB µV dB dBm kΩ dB dB V ICCO1 ICCO2 VGT VG0 VG1 VO max1 THD1 VN1 CT1 CT2 Rr1 VM1 Rg = 2.2 kΩ, RV = 0 Ω With the power switch off VO = –20 dBm, RV = 10 kΩ VO = –20dBm VO = –20dBm THD = 1 % VG = 35.3 dB/NAB, VO = 100 mV Rg = 2.2 kΩ, BPF = 20 Hz to 20 kHz Rg = 2.2 kΩ, TUNE 1 kHz, VO = –20 dBm Rg = 2.2 kΩ, TUNE 1 kHz, VO = –20 dBm Rg = 2.2 kΩ, Vr = –30 dBm, fr = 100 Hz, TUNE 100 Hz VIN = –40 dBm, TUNR 1 kHz, With the muting function on 8.5 54 60 34 100 11 0.1 57 68 35.3 210 0.08 1.3 56 78 52 –90 16 5 60 mA µA dB dB dB mV % µV dB dB dB dBm Symbol Conditions Ratings min typ max Unit 37 0.5 3.0 45 65 45 Output voltage Total harmonic distortion Interchannel crosstalk Output noise voltage Ripple rejection ratio Muting output voltage Input resistance Voltage gain difference [Ripple Filter] Ripple rejection ratio Output voltage [AMSS] Operating output voltage 1.5 33 33 0.89 The preamplifier output voltage VOAMSS1 when the AMSS VO = 0.6 V p-o With the PWR muting on. (AMSS) The preamplifier output voltage VOAMSS2 when the AMSS VO = 0.6 V p-o With the PWR muting off. (BLANK SKIP) The preamplifier output voltage when the AMSS VO = 0.6 V p-o VOAMSS3 With pin 34 shorted through a 270-Ω resistor. With the PWR muting on. The preamplifier output voltage when the AMSS VO = 0.6 V p-o VOAMSS4 With pin 34 shorted through a 270-Ω resistor. With the PWR muting on. VG7 VO max2 Rr4 VM3 VO = –25 dBm THD = 1 % With the input pins open, Vr = –30 dBm, fr = 100 Hz, TUNE 100 Hz VIN = –20 dBm, TUNE 1 kHz, SW OFF 3.33 4.7 6.64 mV Operating output voltage 479 675 953 µV Operating output voltage 2.62 3.7 5.23 mV Operating output voltage [SW AMP] Voltage gain (closed loop) Maximum output voltage Ripple rejection ratio Output voltage when off 375 530 749 µV –1.2 25 50 –0.7 60 75 –0.2 dB mV dB –90 dBm No. 5662-2/5 LA4592W AMSS Temperature Characteristics (Values for reference only) Parameter AMSS Symbol Ta VOAMSS1 Operating output voltage VOAMSS2 The preamplifier output voltage when the AMSS VO = 0.6 V p-o 605 675 735 µV The preamplifier output voltage when the AMSS VO = 0.6 V p-o With the PWR muting on. (AMSS) Conditions Ratings min –10 3.9 typ 25 4.7 max 50 5.4 Unit °C mV Block Diagram System control Ripple filter Bias No. 5662-3/5 LA4592W Test Circuit Diagram System control Ripple filter Bias No. 5662-4/5 LA4592W Sample Application Circuit System control *: Adjust the values of the capacitors marked with an asterisk to match the timing required by the end product. s No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. s Anyone purchasing any products described or contained herein for an above-mentioned use shall: Œ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use:  Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. s Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of July, 1997. Specifications and information herein are subject to change without notice. No. 5662-5/5 Ripple filter Bias