LA4613

Ordering number : EN6014 LA4613 Monolithic Linear IC LA4613 Audio Power Amplifier for Radio Cassette Recorders Overview This is a different-package version of the power amplifier LA4600 with ultralow peripheral component count. Basic power supply spec is VCC = 15V. BS capacitor, NF capacitor, and oscillation prevention CR components are incorporated into the IC circuitry. Package Dimensions unit: mm 3107-SIP13H [LA4613] 25.6 3.4 10.0 2.0 2.4 • Output power : VCC =15V/3Ω....7.0W X 2 • Built-in stanby switch • Built-in overheat protection (TSD) 1.0min 1 0.8 2.0 0.5 13 1.15 0.4 1.2 SANYO : SIP13H Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Thermal resistance Operating temperature Storage temperature Symbol Vcc max Pd max θ j-c Topr Tstg Conditions Rg=0 (No signal) With an arbitrary large heatsink Ratings 24 15.0 3.0 – 20 to +75 – 40 to +150 Unit V W °C/W °C °C Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co., Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN N1298RM(KI) No. 6014-1/7 4.5 13.9 11.2 11.8 15.4max Functions LA4613 Recommended Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Recommended load resistance Operating supply voltage range Operating load resistance range Symbol V CC RL VCC op Within maximum ratings Conditions Ratings 15 3 5.0 to 22 2.7 to 8 Unit V Ω V Ω Electrical Characteristics at Ta = 25°C, VCC = 15V, RL = 3Ω , f = 1 kHz Parameter Standby current Quiescent current Voltage gain Total harmonic distortion Output noise voltage Output voltage Symbol Ist Icco VG THD Vno Po1 Po2 Channel separation Ripple rejection ratio Stanby ON voltage Input resistance Chsep SVRR Vst Ri Conditions min Standby pin –> GND Rg=0 Vo=0 dBm Po=1w Rg=0, DIN AUDIO THD=10% Vcc=9V, RL=4Ω, THD=10% Vo=0 dBm, Rg=0, DIN AUDIO Vr=0 dBm, Rg=0, fr=100 Hz DIN AUDIO 6.0 1.5 50 45 1.5 20 20 43.0 Ratings typ 1.0 35 45.0 0.2 0.15 7.0 2.0 60 55 5.0 30 40 max 10 70 47.0 0.8 0.5 µA mA dB % mV W W dB dB V kΩ Unit Block Diagram Standby 9 Standby switching CH1 input 13 N.C 4 N.C 5 VCC 6 CH1 input amplifier Rf1 RNf1 Predrive amplifier Output amplifier 1 CH1 output Small signal 12 GND RNf2 REF amplifier Rf2 TSD protector 2 Large signal GND CH2 input 11 CH2 input amplifier Predrive amplifier Output amplifier 3 CH1 output Pop noise prevention block 8 P.P 10 N.C Ripple filter 7 Filter No. 6014-2/7 LA4613 Sample Application +5V + 1000µF 9 STANDBY 4 N.C 5 N.C 6 VCC 13 0.22µF ch1 Input ch1 1 Output + 1000µF + 3Ω 12 PRE GND LA4613 POWER GND 2 11 0.22µF ch2 Input ch2 3 Output + + 1000µF 3Ω P.P 8 + N.C 10 4.7µF Filter 7 + 100µF A11492 Pd max – Ta Allowable power dissipation, Pd max – W 16 15 14 12 10 8 6 4 With an arbitrary large heatsink 100X100X1.5mm3 11.7 AI heatsink fastening torque 39N•cm Apply silicone grease 50X50X1.5mm3 5.8 No radiator fin 2 0 –20 0 20 40 60 80 100 Ambient temperature, Ta – ˚C No. 6014-3/7 LA4613 Pin Descriptions 1. Standby switching function (9) Power is switched ON and OFF by controlling the High and Low states at pin 9, respectively (standby). To switch power ON, apply 1.5V or more, or 800 µA to pin 9. . Applied voltage Applied voltage – VBE (approx. 0.7V) + Current supplied to pin 9 = . 2 kΩ 2 kΩ 9 To bias circuit VCC 2kΩ 2kΩ • When directly connecting the microcontroller with this pin, add a resistor in series to optimize the current for the microcontroller. 2. Input pins (11,13) Voltage at the input pins is approx. 2 VBE (1.4V). Input impedance is approx. 30 kΩ. • The recommended value for the input capacitor is 0.22 µF, but this can be varied in order to adjust the starting time (ts). (The starting time is the time required from applying voltage to the standby pin until sound output is obtained.) Input capacitator Starting time ts 1.0 µF 0.2s 2.2 µF 0.3s 3.3 µF 0.5s 4.7 µF 0.65s 10 µF 1.5s 3. Filter (decoupling) pin (7) Pin voltage is approx. 1/2 VCC. The recommended value for the filter capacitor is 100 µF. When capacitance is lower, pop noise when setting the standby pin to Low (power OFF) will increase. Filter capacitor= 100 µF AC voltage (100 mV) Filter capacitor= 47 µF AC voltage (200 mV) Output DC voltage Output DC voltage A11495 A11496 No. 6014-4/7 LA4613 4. P.P (pop noise) pin (8) VCC – VCE (approx. 0.3V) – 5.6V Voltage at pin 8 . . + 5.6V = 2 • The recommended value for the P.P capacitor is 4.7 µF. When capacitance is lower than 2.2 µF, pop noise when setting the standby pin to Low (power OFF) will increase. When capacitance is higher than 10 µF, the sound will not be cut off when setting the standby pin to Low (power OFF). 5kΩ 8 5kΩ VCC Zener voltage =5.6V To input amplifier/ bias circuit A11497 5. Muting The output signal can be controlled by connecting pin 7 (Filter) to ground via a resistance of 300 to 500 Ω. If resistance is higher than 750 Ω, the suppression ratio will decrease. Output AC Voltage Output DC Voltage Mute ON Mute OFF A11498 No. 6014-5/7 LA4613 12 VCC – PO ICCO – mA THD=10% f=1kHz 80 70 60 50 40 30 20 10 0 4 VCC – ICCO Rg=0 10 PO – W 8 Output power, R L= 4Ω 6 4 2 0 4 8 R L= 3Ω Ω =8 RL 12 16 20 24 Quiescent current, 8 12 16 20 24 28 Supply voltage, 10 7 5 3 2 1.0 7 5 3 2 VCC – V VCC=15V RL=3Ω PO=1W Rg=600Ω 100 7 5 3 2 10 7 5 3 2 1.0 7 5 3 2 0.1 7 5 3 2 0.01 0.1 2 Supply voltage, VCC – V THD – f THD – % THD – PO VCC=15V RL=3Ω PO=1W Rg=600Ω Total harmonic distortion, THD – % Total harmonic distortion, 2ch 0.1 7 5 3 2 0.01 10 23 5 7 100 2 3 5 7 1k 23 5 7 10k 23 5 7 100k 2ch 1ch 1ch 3 5 7 1.0 2 3 5 7 10 Frequency, 80 f – Hz 80 Output power, PO – W VCC=15V RL=3Ω Vr=0dBm Rg=0 DIN AUDIO Chsep – f SVRR – dB SVRR – f Chsep – dB 70 70 ch2-ch1 60 60 ch1 ch2 ch1-ch2 Channel separation, 50 Ripple rejection, 3 50 40 40 30 20 2 VCC=15V RL=3Ω VO=0dBm Rg=0 DIN AUDIO 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 30 20 2 3 5 7 100 2 3 5 7 1k 2 3 Frequency, 1 f – Hz 1.0 Frequency, f – Hz f – Response ut= 220 0µF VNO – Rg VCC=15V RL=3Ω DIN AUDIO 0 –1 VNO – mV Output noise voltage, VCC=15V RL=3Ω VO=0dBm 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 5 7 1k 2 3 5 7 10k Response – dB Co –2 –3 –4 –5 –6 –7 –8 10 Cout =100 0 µF 23 5 7 100 23 5 7 1k 23 5 7 10k 23 5 7 100k 2 3 5 7 Frequency, f – Hz Signal source impedance, Rg – Ω No. 6014-6/7 LA4613 10 9 Pd – W 8 7 6 5 4 3 2 1 0 7 0.1 2 3 5 7 1.0 2 3 5 7 10 Pd – W RL=3Ω f=1kHz Rg=600Ω Pd – PO 10 9 8 7 6 5 4 3 2 1 0 7 0.1 2 3 Pd – PO RL=4Ω f=1kHz Rg=600Ω Power dissipation, VC 2 =1 V CC V V CC=9V Power dissipation, = C V 15 5V =1 CC V V =12 VCC VCC=9V 5 7 1.0 2 3 5 7 10 Output power, 6 PO – W RL=8Ω f=1kHz Rg=600Ω Output power, PO – W Pd – PO Pd – W 5 4 Power dissipation, 3 V =15 V CC VCC=12V VC C=9 V 2 1 0 7 0.1 2 3 5 7 1.0 2 3 5 7 10 Output power, PO – W Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 1998. Specifications and information herein are subject to change without notice. PS No. 6014-7/7