LA5617

Ordering number : ENN5671 Monolithic Linear IC LA5617 Multi-System Power Supply for Audio Equipment Overview The LA5617 is a multi-system power supply IC with a built-in on/off control function. It is optimal for use as the power supply IC in CD players, mini-component stereo systems, and other microcontroller controlled audio equipment. Package Dimensions unit: mm 3046D-SIP10F [LA5617] 25.2 24.0 3.6 3.6 Functions • Power supply IC with ±7.5 V outputs (±1.5 A) and an on/off control function. • The LA5617 is pin compatible with the LA5618. 16.7 max 3.5 (8.4) 14.0 1 (1.17) 2.54 1.3 0.5 10 1.6 min 0.45 1.6 Specifications Maximum Ratings at Ta = 25°C Parameter Input voltage Allowable power dissipation Operating temperature Storage temperature Symbol VCC/VEE max Pd max Topr Tstg With no heat sink Conditions SANYO: SIP10F Ratings ±18 2.0 –20 to +85 –55 to +150 Unit V W °C °C Note: On a glass epoxy printed circuit board (114.3 × 76.1 × 1.6 mm) Operating Conditions at Ta = 25°C Parameter Input voltage Output current Symbol VCC/VEE IOUT1 IOUT2 Conditions Ratings ±9.5 to ±16 0 to 1.5 –1.5 to 0 Unit V A A Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 52804TN (OT) No. 5671-1/4 LA5617 Operating Characteristics at Ta= 25°C, VCC/VEE = ±9.5 V, in the specified test circuit. Parameter Symbol Conditions Ratings min typ max Unit [+7.5 V Power Supply Block] IOUT1 = 500 mA, COUT1 = 100 µF Output voltage Dropout voltage Line regulation Load regulation Peak output current Output short current Output off voltage Ripple rejection VO1 VDROP1-1 VDROP1-2 IOUT1 = 300 mA ∆VOLN1 ∆VOLD1 IOP1 IOSC1 VO1OFF Rrej1 VEN = 0.4 V f = 120 Hz, 8.5 V ≤ VCC ≤ 16 V, CN1 = 1 µF –8.0 65 9 V ≤ VCC ≤ 16 V 5 mA ≤ IOUT1 ≤ 1 A VCC/VEE = ±12 V 1.5 7.0 7.5 1.5 1.0 20 80 1.8 1.0 0.3 8.0 2.0 1.5 100 200 V V V mV mV A A V dB [–7.5 V Power Supply Block] IOUT2 = 500 mA, COUT2 = 100 µF Output voltage Dropout voltage Line regulation Load regulation Peak output current Output short current Output off voltage Ripple rejection VO2 VDROP2-1 VDROP2-2 IOUT2 = –300 mA ∆VOLN2 ∆VOLD2 IOP2 IOSC2 VO2 OFF Rrej2 VEN = 0.4 V f = 120 Hz, 16 V ≤ VEE ≤ –8.5 V, CN2 = 1 µF VO1, VO2: Off IOUT1 = 0, IOUT2 = 0 IOUT1 = 1.5 A, IOUT2 = 0 IOUT1 = 0, IOUT2 = 0 IOUT1 = 0, IOUT2 = –1.5 A 5.0 7.0 –5.0 –12.0 –0.3 50 –16 V ≤ VEE ≤ –9 V –1 A ≤ IOUT2 ≤ –5 mA VCC/VEE = ±12 V –7.5 1.5 1.0 200 80 –1.8 –1.0 –7.0 2.0 1.5 300 200 –1.5 V V V mV mV A A V dB [Common Circuit Block] COUT1 = 100 µF, COUT2 = 100 µF Output off control voltage Current drain (positive voltage power supply block) Current drain (negative voltage power supply block) VENL IQP1 IQP2 IQM1 IQM2 0.4 V mA mA mA mA Pd max — Ta 3 Allowable power dissipation, Pd max — W 2 1 1.04 0 –20 0 20 40 60 80 100 Ambient temperature, Ta — °C Pin Assignment LA5617 1 VO1 2 VCC 3 CN1 4 EN 5 TP 6 GND 7 NC 8 CN2 9 VEE 10 VO2 Top view Note: The TP pin is used for IC testing. It must be left open during normal operation. A06994 No. 5671-2/4 LA5617 Equivalent Circuit Block Diagram VCC 2 VO1 CN1 1 Error amplifier VREF 3 Startup circuit VREF GND 6 ON/OFF Thermal protection circuit Current limiter Current limiter VMUTE VCC 140 µA ON/OFF CN2 VCC 60 kΩ Error amplifier VREF 100 Ω 100 kΩ Comparator 1.8 V 30 kΩ 8 VO2 10 VEE 9 4 EN 5 TP Note: The TP pin is used for IC testing. It must be left open during normal operation. A06995 No. 5671-3/4 LA5617 Sample Application Circuit: Mini-component stereo system power supply LA5617 CN1 3 VCC 2 VO1 and VO2 blocks 1 10 1 µF 7.5V Audio circuit block –7.5V VO1 VO2 VEE 9 8 CN2 1 µF Bias blocks 4 EN On/off control 6 GND A06996 Notes: 1. A capacitor with a low temperature coefficient must be used as the EN DELAY delay capacitor. 2. The VO1 and VO2 output capacitors must have values of at least 100 µF and capacitors with low temperature coefficients must be used to prevent oscillation at low temperatures. 3. External noise can be suppressed and ripple rejection improved by adding capacitors between CN1 and VO1 and between CN2 and VO2. Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of May, 2004. Specifications and information herein are subject to change without notice. PS No. 5671-4/4