LA6510_0611

Ordering number : EN2624E LA6510 Overview Monolithic Linear IC Dual Power Operational Amplifier The LA6510 is a dual power operational amplifier IC capable of delivering larger output currents than conventional operational amplifiers. The LA6510 features an on-chip current limiter and provides high voltage gain and a high common-mode rejection ratio. The LA6510 is an ideal choice for power applications such as DC servos, capstan drivers, actuator drivers, programmable power supplies and high-quality audio amplifiers. Functions • High output current (IO max = 1.0A) • High gain • Equipped with current limiter pin • Supports single power source operation Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Differential input voltage Common mode input voltage Maximum output current Allowable power dissipation Operating temperature Storage temperature Symbol VCC / VEE max VID VICOM IO max Pd max Topr Tstg Conditions Ratings ±18 30 ±15 1.0 2.5 -40 to +85 -55 to +150 Unit V V V A W °C °C Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. N2906 MH IM / 92706 / 21506 MS PC / 11906 MS PC B8-7631,7311,7235 / 42000TN(KT) / D250JK No.2624-1/6 LA6510 Electrical Characteristics at Ta = 25°C, VCC / VEE = ±15V Parameter No-load current drain Input offset voltage Input offset current Input bias current Common-mode input voltage range Common-mode signal rejection ratio Output voltage Voltage gain Slew rate Equivalent input noise voltage Supply voltage rejection ratio Limiting current Symbol ICCO VIO IIO IB VICM CMR VO VGO SR VNI SVR ISC Rsc = 2.2Ω GV = 0, RL= 33Ω, R = 2.2Ω, C = 0.1μF Rg = 1kΩ, DIN AUDIO RL=33Ω -15 70 ±12 80 ±13 100 0.15 2 30 0.35 150 RS ≤ 10kΩ Conditions min Ratings typ 12 2 10 100 max 20 6 200 700 +13 mA mV nA nA V dB V dB V/μs μV μV/V A Unit Package Dimensions unit : mm (typ) 3046D 25.2 24.0 3.6 3.6 8 7.5 7 6 5 4 3 2.5 2 1 0 -20 Pd max - Ta With no arbitrarily large heat sink m 5m 1. 0× 12 0× 10 Allowable power dissipation, Pd max - W θj-c • 10°C/W Tightening torque: 4kg • cm 50 × 3 50 ×1 .5m m3 16.7 max With no heat sink (8.4) 14.0 1.6 min 1 (1.17) 2.54 1.3 0.5 10 0 20 40 60 80 100 120 140150160 3.5 Ambient temperature, Ta - °C 0.45 1.6 SANYO : SIP10F Pin Assignment No.2624-2/6 LA6510 Equivalent Circuit Test Circuits 1. Input offset voltage [VIO] Supply voltage rejection ratio [SVR] 2. Output voltage [VO] 3. Common-mode signal rejection ratio [CMR] Common-mode input voltage range [VICM] 4. Input bias current [IB(+)] No.2624-3/6 LA6510 5. Input bias current [IB(-)] 6. Input offset current [IIO] 7. Current drain [ICC] 8. Slew rate [SR] 9. Voltage gain [VGO] 10. Equivalent input noise voltage [VNI] No.2624-4/6 LA6510 Application Circuit Examples Current Limiter Circuit and Output Stage In source mode, when Q3 turns on and current flows into the load resistor, a voltage difference occurs across RSC, turning on Q1 and activating the current limiter. In sink mode, Q4 turns on to develop a voltage difference of the polarity opposite to that in the source mode across RSC, thus turning on Q2 and activating the limiter. A RSC can be use to set the maximum output current, but the maximum output current will vary slightly depending on the VBE temperature characteristics of the transistor. No.2624-5/6 LA6510 Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. T his catalog provides information as of November, 2006. Specifications and information herein are subject to change without notice. PS No.2624-6/6