LA6563

Ordering number : ENN*7887 LA6563 Overview Features Monolithic Linear IC 4CH Bridge (BTL) Driver for CD The LA6563 is a 4CH bridge (BTL) driver for CD players. • Built-in bridge connection (BTL) POWER AMP 4CH • IO max 1A • MUTE circuit (main power is ON/OFF) with 3 systems • Built-in STBY circuit (all circuits are OFF) • Provides bias voltage (VREF) switching function (Select external or internal reference voltage. Internal reference voltage is 2.5V: TYP.) • Output voltage (dynamic range) is high. (6V: TYP) Specifications Maximum Ratings at Ta = 25°C Parameter Power supply voltage Symbol VCC max VS max Pd max VINB IO max VMUTE Topr Tstg Each BTL-AMP of CH1 to CH4 VCC = VS *1 VCC = VS *1 Independent IC*2 Allowable power dissipation Maximum input voltage Maximum output current MUTE pin voltage Operating temperature Storage temperature Specific board (114.3mm × 76.1mm × 1.6mm, glass epoxy resin) *2 Conditions Ratings 14 14 0.8 2.0 13 1 13 -30 to +85 -55 to +150 W V A V °C °C Unit V V *1 VCC and VS must be shorted externally to use. VCC: signal system power supply, VS: power system supply. *2 For information about allowable power dissipation, refer to the reference data of previous models. For more information, it will be described after completing the sample. Recommended Operating Conditions at Ta = 25°C Parameter Power supply voltage Symbol VCC VCC = VS Conditions Ratings 4 to 13 Unit V 61004 JO IM No.7887-1/3 LA6563 Electrical Characteristics at Ta = 25°C, VCC = VS = 8V, VREF = 1.65V, VREF-SW = 3.3V, MUTE1 = MUTE2 = MUTE3 = 3.3V, unless otherwise specified Parameter [Whole] No-load current consumption 1 No-load current consumption 2 No-load current consumption 3 STBY ON voltage STBY OFF voltage STBY hysteresis voltage [Output AMP block] Output offset voltage Output voltage Closed circuit voltage gain Slew rate MUTE ON voltage MUTE OFF voltage MUTE hysteresis voltage [Input OP-AMP block] Output offset voltage Input voltage range Output current (SINK) Output current (SOURCE) [OP-AMP block] Output offset voltage Input voltage range Output current (SINK) Output current (SOURCE) [VREF-AMP block] VREF-AMP offset voltage Internal VREF voltage VREF input voltage range VREF switch voltage 1 VREF switch voltage 2 VOFF-VREF VREF-CONST 1BIN VSW1 VSW2 Select external reference voltage *5 Select internal reference voltage *5 VREF-SW “H” (For external reference voltage selected) VREF-SW “L” (For internal reference voltage selected) -10 2.3 1 3 1 2.5 10 2.7 VCC-1.5 mV V V V V OP-VOFF OP-VIN OP-SINK OP-SOURCE SINK current SOURCE current For BUFFER -10 0 10 10 10 VCC-1.5 mV V mA mA VIN-OFF VIN-OP VIN-SINK VIN-SOURCE 300 For BUFFER -10 0 2 500 10 VCC-1.5 mV V mA µA VOFF VO VG1 SR VMUTE-ON VMUTE-OFF VMUTE-HYS Between (+) and (-) output of each channel RL = 0Ω, Voltage between (+) and (-) output of each channel *1 *2 For output by AMP alone, it must be doubled *3 MUTE *4 MUTE *4 80 5.4 0.5 2 0.5 -50 6 6 6.6 50 mV V times V/µs V V mV ICC-ON ICC-OFF ICC-OFF-STBY STBY-ON STBY-OFF STBY-HYS 80 All AMP output ON, MUTE; HI All AMP output OFF, MUTE; LOW All circuits OFF, STBY: L 2 0.5 30 5 45 10 1 mA mA mA V V mV Symbol Conditions Ratings min typ max Unit *1. Voltage for both ends of the load when connecting the 8Ω load between outputs. Input is H or L. Output is saturated. *2. Input AMP is 0 dB for BUFFER. *3. Design guaranteed performance. *4. MUTE is HI for output ON and LOW for output OFF (AMP output is OFF, HI impedance). Each MUTE activates independently to a corresponding channel. *5. VREF-SW is set to "H" for switching to external reference voltage and "L" for switching to internal reference voltage. No.7887-2/3 LA6563 Package Dimensions unit : mm 3251 PS No.7887-3/3