LA73073CL

Ordering number : ENA0071 LA73073CL Overview LA73073CL is 75Ω Video driver for DSC. Monolithic Linear IC Video Driver for DSC Functions/Features • Not requires output coupling capacity. • Low voltage drive (VCC = 2.8V to 3.6V) • V sag does not occur. • Implements 6th Low Pass Filter (fc = 7.5MHz) • Current dissipation in stand-by mode : 0µA • Selectable amplifier gain of 6dB, 12dB and 16dB. (Pin control (GND/Open/VCC)) • Output drive performance allows up to 75Ω output and single system. Specitications Maximum Ratings at Ta = 25 °C Parameter Maximum supply voltage Allowable power dissipation Operating temperature Storage temperature Symbol VCC max Pd max Topr Tstg Ta ≤ 80°C, ∗Mounted on a board Conditions Ratings 4.0 160 -25 to +80 -55 to +150 Unit V mW °C °C ∗(10×20×0.8mm) Material : Paper phenol Recommended Operating Conditions at Ta = 25 °C Parameter Recommended Operating supply voltage Operating supply voltage range Symbol VCCSTD VCCRANGE Conditions Ratings 3.1 2.8 to 3.6 Unit V V Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. 92706 / 91005 MS PC B8-8039 No.0071-1/6 LA73073CL Electrical Characteristics at Ta = 25°C, VCC = 3.1V Parameter [Current dissipation part] Current dissipation 1 ( VIN = White50% ) Current dissipation 2 ( Non-signal mode ) Current dissipation 3 ( Standby mode ) [Video part] Voltage gain V6 Voltage gain V12 Voltage gain V16 Freq. Characteristic Differential Gain Differential Phase [Control terminal part] Stand-by control terminal H voltage (SET = STANDBY MODE) Stand-by control terminal L voltage (SET = ACTIVE MODE) Gain selection control terminal H voltage (SET = 16dB) Gain selection control terminal M voltage (SET = 12dB) Gain selection control terminal L voltage (SET = 6dB) VTH-G-L VTH-G-M VTH-G-H VTH-STBY-L VTH-STBY-H ICC ≤ 5µA 4-pin terminal voltage range Active mode 4-pin terminal voltage range Amp Gain = 16dB 2-pin terminal voltage range Amp Gain = 12dB 2-pin terminal voltage range Amp Gain = 6dB 2-pin terminal voltage range GND 1.0 1.2 (OPEN) 0.3 V 1.4 V VCC-0.3 VCC V VCC-0.5 GND 3.6 0.3 V V VG-L VG-M VG-H Vf DG DP VIN = 1Vp-p 100% white 2pin = Low (GND) VIN = 0.5Vp-p 100% white 2pin = MID (Open) VIN = 317mVp-p 100% white 2pin = High (VCC) f = 100kHz/5MHz 5.7 11.7 15.7 -1.5 -2.0 -2.0 6.2 12.2 16.2 -0.5 0 0 6.7 12.7 16.7 +0.5 -2.0 -2.0 dB dB dB dB % deg ICC-STBY ICC2 ICC 4pin = Low Input = White50% 4pin = Low Input = No signal 4pin = Open (High) 0 5 µA 7 11.5 15 mA 14 22 30 mA Symbol Conditions min Ratings typ max Unit Package Dimensions unit : mm 3301 No.0071-2/6 LA73073CL LA73073CL Pin Configuration, Pin Function Diagram and Block Diagram No.0071-3/6 LA73073CL Input Output Form Pin No 1 2 Symbol AGND GAINCTL Equivalent Circuit Voltage 0V 1.2V Analog GND Gain select pin Control of Pin2 H(VCC) M(OPEN) L(GND) ⇒ ⇒ ⇒ GAIN 16dB 12dB 6dB Description 3 VIN 1.1V Video input terminal (Sync-tip clamp (input High-impedance)) 4 PSAVCTL VCC or 0V Power save mode select pin Control of Pin4 H(VCC) L(GND) OPEN or VCC±0.5V 0V to 0.3V ⇒ ⇒ MODE STANDBY ACTIVE 5 GND 0V Continued on next page. No.0071-4/6 LA73073CL Continued from preceding page. Pin No 6 Symbol CLKOUT Equivalent Circuit Voltage +3.0V ↑↓ 0V Description Pin : Clock output terminal 7 ND1 +0.5V ↑↓ -2.6V (-VCC) Pin7 : The terminal which transmits an electric charge 8 VCCN 0V ↑↓ -2.5V (-VCC) Pin8 : Negative VCC 9 VOUT 0V Video output terminal (Push-pull output Low-impedance) 10 VCC 2.9V to 3.6V No.0071-5/6 LA73073CL Measurement Circuit Diagram Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of September, 2005. Specifications and information herein are subject to change without notice. PS No.0071-6/6