LB1848MC

Ordering number : ENA2036 Monolithic Digital IC LB1848MC Overview Low-Voltage/Low Saturation Voltage Type Bidirectional Motor Driver The LB1848MC is 2-channel low-voltage, low saturation voltage type bidirectional motor driver IC that is optimal for use as 2-phase stepping motor drivers in printers, cameras and other portable equipment. The output circuits are of the bipolar type, with PNP transistors in the upper side and NPN transistors in the lower side, and they achieve low saturation output and low power characteristics despite being provided in a miniature package. The LB1848MC products can directly control a motor from signals from a microcontroller. The LB1848MC is optimal for 2-phase excitation drive for 2-phase stepping motors using 3-input logic (ENA, IN1 and IN2). Another point is that these IC include built-in thermal shutdown circuits so that IC scorching or burning is prevented in advance even if the IC output is shorted. Functions • Optimal for 2-phase excitation drive for 2-phase stepping motors • Standby current: Zero • Low saturation voltage. VO (sat) = 0.55V typical at IO = 400mA • Thermal shutdown circuit • Through-current prevention circuit • No limitations on the magnitude relationship between the power supply voltage (VCC) and the input voltage (VIN) • “Soft off” function that reduces power supply line noise when switching from drive to standby modes. (Requires the use of one external capacitor.) Specifications Parameter Absolute Maximum Ratings at Ta = 25°C Symbol VCC max VOUT VIN IGND Pd max Topr Tstg Per channel When mounted* Conditions Ratings -0.3 to +8.0 VCC + VSF -0.3 to +8.0 800 820 -20 to +75 -40 to +150 Unit V V V mA mW °C °C Maximum supply voltage Output voltage Input voltage Ground pin outflow current Allowable power dissipation Operating temperature Storage temperature Continued on next page. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. 32112 SY 20120229-S00010 No.A2036-1/6 LB1848MC Continued from preceding page. *1: When mounted on the specified printed circuit board (114.3mm × 76.2mm × 1.5mm), glass epoxy board Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Allowable Operating Ranges at Ta = 25°C Parameter Supply voltage Input high-level voltage Input low-level voltage VIH VIL Symbol VCC Conditions Ratings 2.5 to 7.5 2.5 to 7.5 -0.3 to +0.7 Unit V V V Electrical Characteristics at Ta = 25°C, VCC = 5V Parameter Current drain Symbol ICC0 ICC1 Output saturation voltage VOUT1 VOUT2 Input current IIN IENA Spark Killer Diode Reverse current Forward voltage IS (leak) VSF IOUT = 400mA 30 1.7 µA V Conditions ENA = 0V, VIN = 3V or 0V ENA = 3V, VIN = 3V or 0V ENA = 3V, VIN = 3V or 0V, VCC = 3 to 7.5V, IOUT = 200mA ENA = 3V, VIN = 3V or 0V, VCC = 4 to 7.5V, IOUT = 400mA VIN = 5V ENA = 5V Ratings min typ 0.1 25 0.27 0.55 75 85 max 10 35 0.4 0.8 100 110 Unit µA mA V V µA µA Package Dimensions unit : mm (typ) 3426 5.0 10 6 1000 Pd max -- Ta Allowable power dissipation, Pdmax - mW 820 800 4.4 6.4 0.37 0.835 600 492 400 1 1.0 5 0.35 1.75 MAX 0.15 200 1.5 0.175 0 --20 0 20 40 60 80 100 Ambient temperature, Ta - C SANYO : SOIC10 No.A2036-2/6 LB1848MC Pin Assignment VCC IN2 ENA SOF IN1 1 2 3 4 5 Top view 10 OUT4 9 OUT3 OUT1 OUT2 GND LB1848MC 8 7 6 Block Diagram VCC IN1 OUT1 Stepping Motor OUT2 IN2 Control block ENA Thermal shutdown circuit OUT3 OUT4 GND SOF* 102 to 103 Note: When the “soft off” function is used, a capacitor must be connected to the SOF pin. IF this function is not used, this pin must be left open with absolutely no signals or lines connect. Truth Tables ENA L IN1 L H L H H IN2 L H H L OUT1 OFF H H L L OUT2 OFF L L H H OUT3 OFF H L L H OUT4 OFF L H H L Note: *1 "-" indicates a "don‛t care" input. No.A2036-3/6 LB1848MC SOF pin (“Soft off” function) operation The soft off function reduces power supply line noise due to the kickback current generated when the stepping motor drive mode is switched from drive to standby. The “soft off” function provided by this IC operates when a capacitor (0.001 to 0.01µF) is connected between the SOF pin and ground. (Leave the SOF pin open to disable the soft off function.) The waveforms for each pin are shown below. ENA IN1 IN2 OUT1 OUT2 OUT3 OUT4 No kickback noise VCC SOF No.A2036-4/6 LB1848MC (Cautions) Pay attention to following two points in an application where the capacitor to GND is connected to the SOF pin: (1) Sudden startup of VCC power supply causes charging of the capacitor from the IC inside via the SOF pin at startup. During charging, the state equivalent to the one with the ENA input at “H” occurs, causing output of the corresponding logic to the output pin, which may result in driving of the load. (The output time period is dependent on the capacity of capacitor; about 2 ms for 0.01μF.) (2) To transfer from the drive mode to the standby mode by changing the ENA input from “H” to “L”, the capacitor is charged from the IC inside via the SOF pin as in the case of above (1). During this charge period, the ENA input keeps the “H” condition in IC. By changing IN1/IN2 input at this time point, the output can be changed. (The time period is equal to that of (1) above.) VCC Q1 Q2 R1 60kW ENA 43kW Drive circuit R2 SOF 80kW GND [SOF pin internal equivalent circuit diagram] 50 ICC - VCC Characterstics VCC=VIN, IN1 / 2 / 3 / 4=H / L / H / L 300W External capacitor 280 IIN -- VIN VCC=5V 240 40 Current drain, ICC - mA 30 Input current, IIN - μA 0 1 2 3 4 5 6 7 8 9 200 160 20 120 80 10 40 0 0 0 1 2 3 4 5 6 7 8 9 Power-supply voltage, VCC - V 1.0 VOUT -- IOUT Input voltage, VIN - V Output saturation voltage, VOUT - V VCC=VIN=4.0V 0.8 0.6 0.4 0.2 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Input current, IOUT - A No.A2036-5/6 LB1848MC SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. T his catalog provides information as of March, 2012. Specifications and information herein are subject to change without notice. PS No.A2036-6/6