LB1930MC

Ordering number : ENA2018 Monolithic Digital IC LB1930MC Overview Low-Voltage, Low-Saturation Bidirectional Motor Driver The LB1930MC is single-channel forward/reverse DC brush motor driver. This device is optimal for CD, DVD and Blue Ray Disk player loading motors. And it is possible to use it for others as a general-purpose product. Features • The low saturation voltage reduces IC internal heating and allows a high voltage to be applied to the motor. Thus this device can be used even in environments with a high operating ambient temperature. Output saturation voltage: Vsat1 = 0.25V typical (IO = 0.2A) (High side + low side): Vsat2 = 0.55V typical (IO = 0.5A) Operating temperature range: Ta = -30 to +85°C • The LB1930MC features the wide operating voltage range of 2.2 to 10.8V and the low standby current drain of 0.1μA, and therefore can easily be used in battery operated systems. • To minimize through currents, the LB1930MC internal logic passes through an internal standby state when switched by the input signals between forward/reverse and brake, or between forward and reverse. • There are no constraints on the relationship between the input voltage and the supply voltage. For example, the LB1930MC can be used with VCC = 3V, and VIN = 5V. • If the IC chip exceeds 180°C due to an output short causing a large current flow, the built-in thermal protection circuit suppresses the drive current to prevent fires or destruction of the IC. Specifications Parameter Supply voltage Output current Output voltage handling Applied input voltage Absolute Maximum Ratings at Ta = 25°C Symbol VCC max IOUT max VOUT max IH max Conditions Ratings 11 1000 VCC + VSF 10.5 Unit V mA V V Continued on next page. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. 32112 SY 20120228-S00004 No.A2018-1/5 LB1930MC Continued from preceding page. Parameter Allowable power dissipation Operating temperature Storage temperature Symbol Pd max Topr Tstg Conditions Mounted on a specified board * Ratings 750 -30 to +85 -55 to +150 Unit mW °C °C * Specified board: 114.3mm × 76.1mm × 1.6mm, glass epoxy board. Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Allowable Operating Ranges at Ta = 25°C Parameter Supply voltage High-level input voltage Low-level input voltage Symbol VCC VIH VIL Conditions Ratings 2.2 to 10.8 2.0 to 10 -0.3 to +0.3 Unit V V V Electrical Characteristics at Ta = 25°C, VCC = 3V Ratings Parameter Current drain Symbol ICC1 ICC2 ICC3 Output saturation voltage VO(sat)1 VO(sat)2 VO(sat)3 Input current Thermal detection operating temperature IIN THD Standby mode Forward or reverse drive operation Braking Forward or reverse drive: High side + low side, IO = 200mA Forward or reverse drive: High side + low side, IO = 500mA Forward or reverse drive: High side only, IO = 200mA VIN = 5V Design guarantee value* 150 Conditions min typ 0.1 15 22 0.25 0.55 0.15 70 180 max 5 21 31 0.35 0.75 0.25 95 200 μA mA mA V V V μA °C Unit * Design guarantee value, Do not measurement. Package Dimensions unit : mm (typ) 3426 5.0 1000 Pd max -- Ta Spesified board: 114.3×76.1×1.6mm3 glass epoxy board. Allowable power dissipation, Pd max -- mW 10 6 800 750 4.4 6.4 0.37 0.835 600 1 1.0 5 0.35 1.75 MAX 0.15 400 390 200 1.5 0 -30 -20 0 20 40 60 80 85 100 0.175 Ambient temperature, Ta -- C SANYO : SOIC10 No.A2018-2/5 LB1930MC Pin Assignment VCC 1 10 NC LB1930MC Top view VCC 1 NC 2 IN1 3 IN2 4 S-GND 5 9 OUT1 8 NC 7 OUT2 6 P-GND Block Diagram and Application Circuit Example C1=1μF IN1 3 60kΩ 80kΩ Control block OUT1 9 CPU IN2 4 60kΩ M 7 OUT2 80kΩ 5 S-GND 6 P-GND Truth Table IN1 L H L H IN2 L L H H OUT1 OFF H L H OUT2 OFF L H H Mode Standby Forward Reverse Brake No.A2018-3/5 LB1930MC 1.0 VO(sat) -- IO Output saturation voltage, VO(sat) -- V Ta = 25°C VCC = 5V 1.0 VO(sat) -- Tc Output saturation voltage, VO(sat) -- V 0.9 0.9 0.6 0.6 I O = 50 0mA total (Low + High side) 0.4 0.4 IO = 200mA 0.2 0.2 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 -40 -20 0 20 40 60 80 100 120 140 Output current, IO -- A 28 Case temperature, Tc -- °C 20 ICC -- VCC ICC -- Tc Forward/reverse 24 Brake 16 Current drain, ICC -- mA 20 Forward/reve 16 rse Current drain, ICC -- mA VC C = 8V 12 VCC = 3V 12 8 8 VCC = 2V 4 4 0 0 1 2 3 4 5 6 7 8 9 10 11 12 0 -40 -20 0 20 40 60 80 100 120 140 Supply voltage, VCC -- V 28 Case temperature, Tc -- °C Brake 160 ICC -- Tc IIN -- VIN VCC = 3V 24 Current drain, ICC -- mA 20 16 VCC = 3V Input current, IIN -- μA VC C = 8V 120 80 12 VCC = 2V 8 40 4 0 -40 -20 0 20 40 60 80 100 120 140 0 0 1 2 3 4 5 6 7 8 9 10 Case temperature, Tc -- °C 1.8 1.6 80 ICC Standby Temperature Characteristics VCC = 11V 100 IN pin Input Current vs. Temperature Characteristics VIN = 5V Input voltage, VIN -- V Current drain, ICC -- μA 1.2 Input current, IIN -- μA Under 0.01μA 0.29 60 0.8 40 0.4 20 0 -40 -20 0 20 40 60 80 100 120 140 0 -40 -20 0 20 40 60 80 100 120 140 Case temperature, Tc -- °C Case temperature, Tc -- °C No.A2018-4/5 LB1930MC Usage Notes Oscillation may occur in the VCC and P-GND lines, since these lines carry a wide range of currents. The following may help if this is a problem. (1) Lower the inductance of the wiring by making lines wider and shorter. (2) Insert capacitors with good frequency characteristics close to the IC. (3) Consider adopting the following methods if the CPU and this IC are mounted on different printed circuit boards that could easily have different ground potentials. • Connect S-GND to the CPU ground and connect P-GND to the power system ground. • Insert resistors of about 10kΩ in series between the controller outputs and the inputs on this IC. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of March, 2012. Specifications and information herein are subject to change without notice. PS No.A2018-5/5