LV7150V_0712

Ordering number : ENA0896A LV7150V Overview Bi-CMOS IC Switch for the Wideband Video Signal (with LPF) The LV7150V is switch for the wideband video signal. It has the two input switches by three channels. It built in the 6MHz/12MHz/30MHz-LPF. It is the best for the filter to remove the digital clock noise of the Y/Pb/Pr or RGB Analog video signal before the A/D converter. It can correspond to the full HD signal because it provides the flat frequency response to 60MHz. Functions • Two input switches × three channels • Y/Pb/Pr and RGB signal inputs • Flat frequency response to 60MHz (Bypass filter) • 6MHz/12MHz/30MHz-LPF Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Operating temperature Storage temperature Symbol VCC max Pd max Topr Tstg Ta≤75°C Mounted on a specified board * Conditions Ratings 6 300 -20 to +75 -40 to +125 Unit V mW °C °C Note *: Mounted on a specified board: 114.3mm×76.1mm×1.6mm glass epoxy Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. D1907 TI IM 20071127-S00006 / 72507 TI IM No.A0896-1/7 LV7150V Recommended Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Operating supply voltage Range Symbol VCC VCC opg Conditions Ratings 5 4.75 to 5.25 Unit V V Electrical Characteristics at Ta = 25°C, VCC = 5.0V Parameter Input Point Input signal Signal Freq Mag Out Point Test Condition min Ratings typ max unit VCC supply current & Internal reference regulator VCC supply current Internal reference regulator voltage Voltage gain Voltage gain Py/Pb/Pr R/G/B Frequency response Frequency response at LPF_Through Frequency response 1 at 6MHz_LPF Frequency response 2 at 6MHz _LPF Frequency response 1 at 12MHz_LPF Frequency response 2 at 12MHz_LPF Frequency response 1 at 30MHz_LPF Frequency response 2 at 30MHz_LPF Frequency response 3 at 30MHz_LPF S/N S/N ratio at 30MHz_LPF Py R G B Crosstalk Crosstalk Py/Pb/Pr R/G/B T1A T2A T4A T5A T7A T8A SIG2 5M 700mVpp T15 T13 T11 The ratio of the output leak of the non-selection input -60.0 -55.0 dB T1A T2A T4A T5A T7A T8A SIG1 T15 650mVpp T13 T11 30MHz_LPF is selected, The S/N ratio from 100kHz to 30MHz -60.0 -50.0 dB Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A SIG2 SIG2 SIG2 SIG2 SIG2 SIG2 SIG2 SIG2 60M 100k 6M 100k T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 LPF_Through is selected, Output gain difference between 100kHz and 60MHz 6MHz_LPF is selected, Output gain difference between 100kHz and 6MHz 6MHz_LPF is selected, Output gain difference between 100kHz and 13.5MHz 12MHz_LPF is selected, Output gain difference between 100kHz and 12MHz 12MHz_LPF is selected, Output gain difference between 100kHz and 27MHz 30MHz_LPF is selected, Output gain difference between 100kHz and 20MHz 30MHz_LPF is selected, Output gain difference between 100kHz and 30MHz 30MHz_LPF is selected, Output gain difference between 100kHz and 74MHz -45.0 -33.0 dB -3.5 -1.0 1.5 dB -1.0 0.0 1.0 dB -30.0 -20.0 dB -3.0 0.0 1.0 dB -30.0 -20.0 dB -3.0 0.0 1.0 dB -3.0 -1.0 1.0 dB T1A T2A T4A T5A T7A T8A SIG2 100k 300mVpp T15 T13 T11 Output gain for input -0.5 -0.2 0.0 dB V3 T16 At non-signal, The current flows to 3pin The voltage of 16pin 2.8 3.0 3.2 V 26 34 42 mA 13.5M 100k Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B 12M 100k 27M 100k 20M 100k 30M 100k 74M 100k 30M 100k Continued on next page. No.A0896-2/7 LV7150V Continued from preceding page. Parameter Group delay Group delay at LPF_Through Group delay at 6MHz_LPF Group delay at 12MHz_LPF Group delay at 30MHz_LPF Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A T1A T2A T4A T5A T7A T8A SIG2 SIG2 SIG2 SIG2 60M 100k 6M 100k 12M 100k 30M 100k T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 T15 300mVpp T13 T11 LPF_Through is selected, Delay difference between 100kHz and 60MHz 6MHz_LPF is selected, Delay difference between 100kHz and 6MHz 12MHz_LPF is selected, Delay difference between 100kHz and 12MHz 30MHz_LPF is selected, Delay difference between 100kHz and 30MHz 10.0 20.0 ns 20.0 40.0 ns 40.0 70.0 ns 0.5 2.0 ns Input Point Input signal Signal Freq Mag Out Point Test Condition min Ratings typ max unit Package Dimensions unit : mm (typ) 3178B 5.2 16 9 4.4 6.4 1 0.65 (0.33) 8 0.15 0.22 1.5max SANYO : SSOP16(225mil) Pin Control Table Pin Control Table SW No. SW1 SW2 SW3 SW4 Pin No. Pin12 Pin10 Pin9 Pin14 SW function name CLAMP/BIAS_CTL Filter_CTL1 Filter_CTL2 Input_Select_CTL Input Control Table CLAMP/BIAS_CTL Low (0 to 0.7V) High (2.3V to VCC) Mode selected CLAMP (Y/Pb/Pr_Mode) BIAS (RGB_Mode) 0.1 (1.3) 0.5 Continued on next page. No.A0896-3/7 LV7150V Continued from preceding page. Filter Control Table Filter_CTL1 Low (0 to 0.7V) Low (0 to 0.7V) High (2.3V to VCC) High (2.3V to VCC) Filter_CTL2 Low (0 to 0.7V) High (2.3V to VCC) Low (0 to 0.7V) High (2.3V to VCC) Mode selected 6Mz_LPF 12Mz_LPF 30Mz_LPF LPF_Through Input Select Control Table Input_Select_CTL Low (0 to 0.7V) High (2.3V to VCC) Mode selected CH1_select CH2_select Block Diagram Pr/R_IN1 1F + 1 BIAS 100k SW4: Input_Select _CTL VREG_3V 6MHz LPF 12MHz LPF BUF 30MHz LPF Through SW2&SW3: Filter_CTL 16 1F + Pr/R_IN2 1F + 2 BIAS 100k 15 10 F + Pr/R_OUT VCC 3 6MHz LPF 14 SW4:Input_Select_CTL Py/G_IN1 1F + CLAMP 12MHz LPF BUF SW1: CLAMP/BIAS_ CTL SW4: Input_Select _CTL SW1: CLAMP/BIAS_ CTL 30MHz LPF Through 4 BIAS 100k 13 10 F + Py/G_OUT SW2&SW3: Filter_CTL Py/G_IN2 1F + CLAMP 5 BIAS 100k 12 6MHz LPF 12MHz LPF SW1:CLAMP/BIAS_CTL GND 6 BUF 30MHz LPF Through SW2&SW3: Filter_CTL 11 10 F + Pb/B_OUT Pb/B_IN1 1F + 7 BIAS 100k 10 SW2:Filter_CTL1 Pb/B_IN2 1F + 8 BIAS 100k SW4: Input_Select_CTL 9 SW3:Filter_CTL2 No.A0896-4/7 LV7150V Pin Function Pin No. P1 Pin name Pr/R_IN1 DC voltage 2.3V Signal wave form Input/Output form P2 Pr/R_IN2 2.3V P3 P4 VCC Py/G_IN1 Y/Pb/Pr: 1.8V (Clamp) RGB: 2.3V (Bias) P5 Py/G_IN2 Y/Pb/Pr: 1.8V (Clamp) RGB: 2.3V (Bias) P6 P7 GND Pb/B_IN1 2.3V Continued on next page. No.A0896-5/7 LV7150V Continued from preceding page. Pin No. P8 Pin name Pb/RB_IN2 DC voltage 2.3V Signal wave form Input/Output form P9 Filter_CTL2 High: 2.3 to VCC Low: 0 to 0.7V P10 Filter_CTL1 High: 2.3 to VCC Low: 0 to 0.7V P11 Pb/B_OUT 2.3V 200 50 11 200 P12 CLP/BIAS_CTL High: 2.3 to VCC RGB (Bias) Low: 0 to 0.7V Y/Pb/Pr (Clamp) P13 Py/G_OUT Y/Pb/Pr: 1.8V (Clamp) RGB: 2.3V (Bias) Continued on next page. No.A0896-6/7 LV7150V Continued from preceding page. Pin No. P14 Pin name Input_Select_CTL DC voltage High: 2.3 to VCC Ch2 Low: 0 to 0.7V Ch1 Signal wave form Input/Output form P15 Pr/R_OUT 2.3V P16 REG3V 3.0V SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of December, 2007. Specifications and information herein are subject to change without notice. PS No.A0896-7/7