LV8417CS

Ordering number : ENA1996 LV8417CS Overview Bi-CMOS IC Forward/Reverse Motor Driver The LV8417CS is a 1-channel H bridge motor driver IC. The package size is extremely small with wafer level package (WLP). Moreover, the on-resistance is low (upper and lower total 0.27Ω typ.). The application voltage range is wide (2.0V to 10.5V). The H bridge of this IC is P-N composition and thereby reduces the external parts without need of charge pump. Therefore, LV8417CS realizes reduction of mounting area which enables lower cost and smaller application size. Functions • H-bridge 1-channel forward/reverse motor driver • IO max=1.0A (t≤100ms 2.0A, t≤10ms 3.8A) • BiCDMOS process • Built-in low voltage reset and thermal shutdown circuit • Output ON resistance (Upper and lower total 0.27Ω; Ts=25°C, IO=1.0A) Specifications Parameter Maximum Ratings at Ta = 25°C, SGND = PGND = 0V Symbol VM max VCC max IO max IO peak1 IO peak2 Input voltage Allowable power dissipation Operating temperature Storage temperature VIN max Pd max Topr Tstg Mounted on a specified board * t ≤ 100ms t ≤ 10ms Conditions Ratings -0.5 to 12.6 -0.5 to 6.0 1.0 2.0 3.8 -0.5 to VCC+0.5 850 -20 to +85 -55 to +150 Unit V V A A A V mW °C °C Power supply voltage (for load) Power supply voltage (for control) Output current Output peak current * Specified board : 57mm × 57mm × 1.6mm, glass epoxy both side board. Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. D0711 SY 20111012-S00003 No.A1996-1/5 LV8417CS Allowable Operating Conditions at Ta = 25°C, SGND = PGND = 0V Parameter Power supply voltage (VM pin) Power supply voltage (VCC pin) Input signal voltage Input signal frequency Symbol VM VCC VIN f max Duty = 50% Conditions Ratings 2.0 to 10.5 2.7 to 5.5 0 to VCC 200 Unit V V V kHz Electrical Characteristics Ta = 25°C, VCC = 3.0V, VM = 6.0V, SGND = PGND = 0V Parameter Standby load current drain Operating load current drain Standby control current drain Operating current consumption 1 High-level input voltage Low-level input voltage High-level input current (ENA,IN1, IN2) Low-level input current (ENA,IN1, IN2) Pull-down resistance value Output ON resistance Low-voltage detection operating voltage Low-voltage detection release voltage Thermal shutdown temperature Output block Turn-on time Output response time H Turn-off time Output response time L TPHL TIOL No load No load, Design guarantee * 8 9 0.10 0.25 0.15 0.38 μs μs Tth TPLH TIOH Design guarantee * No load No load, Design guarantee * 7 8 9 150 180 0.10 0.23 210 0.15 0.35 °C μs μs VCS2 VCC pin voltage 6 2.3 2.5 2.7 V RDN RON VCS1 ENA, IN1, IN2 Sum of top and bottom sides ON resistance. VCC pin voltage 4 5 6 2.1 100 200 0.27 2.3 400 0.4 2.5 kΩ Ω V IIL1 VIN = 0V -1.0 μA Symbol IMO IM1 ICO IC1 VIH VIL IIH1 ENA = 0V ENA = 3.0V, No load ENA = IN1 = IN2 = 0V ENA = 3.0V, No load 2.7 ≤ VCC ≤ 5.5V 2.7 ≤ VCC ≤ 5.5V VIN = 3V Conditions Remarks 1 3 2 3 0.6×VCC 0 20 0.5 80 Ratings min typ max 1.0 120 1.0 0.8 VCC 0.2×VCC 30 Unit μA μA μA mA V V μA Remarks 1. Current consumption when output at the VM pin is off. 2. Current consumption at the VCC pin when in all function stop. 3. Current consumption at the VCC pin when ENA=3V(IC starting time). 4. ENA, IN1 and IN2 pin have an internal pull-down resistor. 5. The saturation voltage of the bottom above an OUT pin is added, and the value broken by the current value is shown. 6. All output transistors are turned off if a low-voltage is detected for VCC. 7. All output transistors are turned off if the thermal protection circuit is activated. They are turned on again as the temperature goes down. 8. Rising time from 10 to 90% and falling time from 90 to 10% are specified. 9. Time until it changes OUT pin voltage 10% from the time of change of input pin voltage being 50% of VCC is specified. IN 50% 50% 90% 90% OUT 10% TPLH TIOL TPHL 10% TIOH No.A19965-2/5 LV8417CS Package Dimensions unit : mm (typ) 3418 TOP VIEW 1.47 A SIDE VIEW BOTTOM VIEW 0.235 1.5 Pd max -- Ta Specified board: 57×57×1.6mm3 glass epoxy both side board. Allowable power dissipation, Pd max -- W 1.47 B C 1.0 0.85 3 0.27 2 1 0.235 0.5 0.55 MAX 0.5 (0.42) SIDE VIEW 0.5 0.44 0.08 SANYO : WLP9(1.47X1.47) 0 -20 0 20 40 60 80 85 100 Ambient temperature, Ta -- C Pin Assignment Ball side view Top view A 0.5mm B C C B A 1 0.5mm OUT2 PGND OUT1 1 OUT1 PGND OUT2 1.47mm 2 VM SGND VCC 2 VCC SGND VM 3 IN2 IN1 ENA 3 ENA IN1 IN2 1.47mm Block Diagram VCC + - VM Starting control block Thermal protection circuit OUT1 + - ENA Output pre stage Low voltage protection circuit OUT2 IN1 IN2 Motor control logic PGND SGND No.A19965-3/5 LV8417CS Pin Functions Pin No. C-3 B-3 A-3 C-2 B-2 Pin name ENA IN1 IN2 VCC SGND Logic enable pin Driver output change pin Driver output change pin Power supply for control Ground pin for control Description Equivalent circuit VCC ENA/IN1/IN2 SGND A-2 C-1 A-1 B-1 VM OUT1 OUT2 PGND Power supply for load Driver output pin Driver output pin Ground pin for load VM OUT1 OUT2 PGND Truth Table ENA L IN1 L H H L H IN2 L L H H OUT1 Z Z H L L OUT2 Z Z L H L Mode All function stop Standby Forward Reverse Brake - : denotes a don't care value. Z : High-impedance • Current drain is zero in all function stop mode. • All power transistors turn off and the motor stops driving when the IC is detected in low voltage or thermal protection mode. No.A19965-4/5 LV8417CS Sample Application Circuit Motor connect pin OUT1 OUT2 OUT1 PGND OUT2 VCC SGND VM ENA IN1 IN2 SW1 VCC (Power pin for control) SW2 SW3 VM (Power pin for loads) VIN (Power pin for switch) ENA IN1 Logic input pin IN2 * Connect a kickback absorbing capacitor as close as possible to the IC. Characteristics deterioration of the IC or damage may result if an instantaneous voltage surge exceeding the maximum rated value is applied to the VM line due to coil kickback or other causes. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of December, 2011. Specifications and information herein are subject to change without notice. PS No.A1996-5/5