STK433-090-E

Ordering number : EN*A1248 Thick-Film Hybrid IC STK433-090-E Overview 2-channel class AB audio power IC, 80W+80W The STK433-090-E is a hybrid IC designed to be used in 80W × 80W (2-channel) class AB audio power amplifiers. Applications • Audio power amplifiers. Features • Pin-to-pin compatible outputs ranging from 80W to 150W. • Can be used to replace the STK433-200, STK433-300 series (3-channel) due to its pin compatibility. • Miniature package (67.0mm × 25.6mm × 9.0mm) • Output load impedance: RL = 6Ω supported • Allowable load shorted time: 0.3 second • Allows the use of predesigned applications for standby and mute circuits. Series Models STK433-090-E Output 1 (10%/1kHz) Output 2 (0.4%/20Hz to 20kHz) Max. rated VCC (quiescent) Max. rated VCC (6Ω) Recommended operating VCC (6Ω) Dimensions (excluding pin height) 80W×2 channels 50W×2 channels ±54V ±47V ±33V STK433-100-E 100W×2 channels 60W×2 channels ±57V ±50V ±35V STK433-120-E 120W×2 channels 80W×2 channels ±65V ±57V ±40V STK433-130-E 150W×2 channels 100W×2 channels ±71.5V ±63V ±44V 67.0mm×25.6mm×9.0mm Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 31809HKIM No. A1248-1/11 STK433-090-E Specifications Absolute maximum ratings at Ta=25°C (excluding rated temperature items), Tc=25°C unless otherwise specified Parameter Maximum quiescent supply voltage 0 Maximum supply voltage 1 Minimum operating supply voltage Maximum operating flow-in current (pin 13) Thermal resistance Junction temperature IC substrate operating temperature Storage temperature Allowable load shorted time *4 *7 Symbol VCC max (0) VCC max (1) VCC min IST OFF max θj-c Tj max Tc max Tstg ts VCC=±33V, RL=6Ω, f=50Hz, PO=50W, 1-channel active Per power transistor Both the Tj max and Tc max conditions must be met. When no signal RL≥6Ω Conditions Ratings ±54 ±47 ±10 0.6 2.1 150 125 -30 to +125 0.3 Unit V V V mA °C/W °C °C °C s Operating Characteristics at Tc=25°C, RL=6Ω, Rg=600Ω, VG=30dB, non-inductive load RL, unless otherwise specified Conditions *2 Parameter Output power *1 Symbol PO (1) PO (2) Total harmonic distortion *1 THD (1) THD (2) Frequency characteristics *1 Input impedance Output noise voltage Quiescent current Output neutral voltage Current flowing into pin13 in standby mode operating mode *7 IST OFF *7 Current flowing into pin13 in *3 fL, fH ri VNO ICCO VN IST ON VCC (V) ±33 ±33 ±33 ±33 ±33 ±33 ±39 ±39 ±39 ±33 ±33 Voltage at pin13: 5V, Current limiting resistance R1: 13kΩ 0.25 0.6 mA 1k f (Hz) 20 to 20k 1k 20 to 20k 1k 1.0 1.0 Rg=2.2kΩ No loading 20 -70 45 0 +0 -3dB 5.0 PO (W) THD (%) 0.4 10 VG=30dB 0.01 20 to 50k 55 1.0 80 +70 0 Hz kΩ mVrms mA mV mA min 47 Ratings unit typ 50 80 0.4 % max W [Remarks] *1: For 1-channel operation *2: Unless otherwise specified, use a constant-voltage power supply to supply power when inspections are carried out. *3: The output noise voltage values shown are peak values read with a VTVM. However, an AC stabilized (50Hz) power supply should be used to minimize the influence of AC primary side flicker noise on the reading. *4: Use the designated transformer power supply circuit shown in the figure below for the measurement of allowable load shorted time and output noise voltage. *5: The –Pre VCC (pin 1) line must be at the lowest level under any circumstances. *6: Thermal design must be implemented based on the conditions under which the customer’s end products are expected to operate on the market. *7: Be sure to use the current limiting resistor to prevent the current flowing into the standby pin (pin13) never exceeds the maximum rated value in operating mode. The circuit is turned on by applying VBE (approximately 0.6V) or higher voltage to the standby pin (pin13). *8: A thermoplastic adhesive resin is used for this hybrid IC. DBA40C 10000μF + +VCC 500Ω Designated transformer power supply (MG-200 equivalent) + 500Ω 10000μF -VCC No. A1248-2/11 STK433-090-E Package Dimensions unit:mm (typ) 67.0 60.0 (R1.8) 9.0 5.0 16.0 25.6 20.8 3.6 1 2.0 (16.0) 14 2.0=28.0 15 0.5 4.0 0.4 2.9 5.5 Internal Equivalent Circuit 3 8 Pre Driver CH1 11 12 + - Pre Driver CH2 15 14 + - Bias Circuit 1 2 SUB 10 9 54 67 13 No. A1248-3/11 STK433-090-E Application Circuit Example STK433-090-E -PRE -VCC +VCC Ch1 OUT Ch1 OUT Ch2 OUT Ch2 OUT +PRE SUB GND Ch1 IN Ch1 NF ST-BY Ch2 NF Ch2 IN 1 2 3 0.22Ω 4 5 0.22Ω 6 7 8 9 10 11 12 13 14 15 Stand-by Control (V#13) 100pF 100pF 100Ω /1W 56kΩ 56kΩ 3pF 56kΩ 3pF 1.8kΩ 10μF /10V 1.8kΩ 10μF /10V 2.2μF /50V 470pF 1kΩ Ch2 IN GND Ch1 IN 3μH 2.2μF /50V +VCC 100μF /100V 100μF /100V 0.1μF 100Ω/1W 100μF /100V 4.7Ω 4.7Ω/1W 470pF 1kΩ 56kΩ Ch2 OUT GND 100μF /100V 3μH GND GND 4.7Ω/1W 0.1μF -VCC 4.7Ω Ch1 OUT SUB.GND Sample PCB Trace Pattern C23 No. A1248-4/11 STK433-090-E STK433-100/STK433-300Sr PCB PARTS LIST PCB Name: STK403-000Sr/100Sr/200Sr PCBA Location No. * 2ch AMP doesn’t mount parts of ( ). Hybrid IC#1 Pin Position R01 R02, R03 (R4) R05, R06, R08, R09 (R7, R10) R11, R12 (R13) R14, R15 (R16) R17, R18 (R19) R20, R21 (R22) C01, C02, C03, C23 C04, C05 (C06) C07, C08 (C09) C10, C11 (C12) C13, C14 (C15) C16, C17 (C18) C19, C20 (C21) R34, R35 (R36) L01, L02 (L3) Stand-By Control Circuit Tr1 D1 R30 R31 R32 R33 C32 J1, J2, J3, J4, J5, J6, J8, J9 J7, JS2, JS3, JS4, JS5, JS7 JS8, JS9 JS6, JS10 JS1 ERG1SJ101 (*3) ERG1SJ101 RN16S102FK RN16S563FK RN16S182FK RN14S4R7FK ERX1SJ4R7 ERX2SJR22 100MV100HC 50MV2R2HC DD104-63B471K50 DD104-63CJ030C50 10MV10HC ECQ-V1H104JZ DD104-63B***K50 RN16S302FK 2SC2274 (Reference) GMB01 (Reference) RN16S***FK RN16S333FK RN16S102FK RN16S202FK 10MV33HC 100Ω, 1W PARTS RATING Component 100Ω,1W 1kΩ, 1/6W 56kΩ, 1/6W 1.8kΩ, 1/6W 4.7Ω, 1/4W 4.7Ω, 1W 0.22Ω, 2W 100μF, 100V 2.2μF, 50V 470pF, 50V 3pF, 50V 10μF, 10V 0.1μF, 50V ***pF, 50V 3kΩ, 1/6W 3μH STK433-100Sr (*2) enabled enabled enabled enabled enabled enabled enabled enabled enabled (*1) enabled enabled enabled (*1) enabled 100pF Short enabled enabled enabled 13kΩ enabled enabled enabled enabled enabled enabled enabled 2.7kΩ 68pF STK433-300Sr VCE≥50V, IC≥10mA Di ***kΩ, 1/6W 33kΩ, 1/6W 1kΩ, 1/6W 2kΩ, 1/6W 33μF, 10V (*1) Capacitor mark “A” side is “-” (negative). (*2) STK433-100Sr (2ch AMP) doesn’t mount parts of ( ). (*3) Add parts C23 to the other side of PCB. No. A1248-5/11 STK433-090-E Pin Assignments [STK433-000/-100/-200Sr & STK415/416-100Sr Pin Layout] 1 2ch class-AB STK433-030-E 30W/JEITA STK433-040-E 40W/JEITA STK433-060-E 50W/JEITA STK433-070-E 60W/JEITA STK433-090-E 80W/JEITA STK433-100-E 100W/JEITA STK433-120-E 120W/JEITA STK433-130-E 150W/JEITA 1 3ch class-AB STK433-230A-E 30W/JEITA STK433-240A-E 40W/JEITA STK433-260A-E 50W/JEITA STK433-270-E 60W/JEITA STK433-290-E 80W/JEITA STK433-300-E 100W/JEITA STK433-320-E 120W/JEITA STK433-330-E 15W/JEITA 1 2ch class-H STK415-090-E 80W/JEITA STK415-100-E 90W/JEITA STK415-120-E 120W/JEITA STK415-130-E 150W/JEITA STK415-140-E 180W/JEITA + V L V L + O F F S E T 1 3ch class-H STK416-090-E 80W/JEITA STK416-100-E 90W/JEITA STK416-120-E 120W/JEITA STK416-130-E 150W/JEITA + V L V L + O F F S E T O F F S E T P R E V H + V H O U T / C H 1 + O U T / C H 1 2 3 O F F S E T 4 5 6 7 P R E V H + V H O U T / C H 1 + 8 O U T / C H 1 9 2 3 4 5 6 7 P R E V C C + V C C O U T / C H 1 + 8 O U T / C H 1 9 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 P R E V C C + V C C O U T / C H 1 + O U T / C H 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2ch classAB/2.00mm O U T / C H 2 + O U T / C H 2 + P R E S U B • G N D G N D I N / C H 1 N F / C H 1 S T A N D | B Y N F / C H 2 I N / C H 2 3ch classAB/2.00mm O U T / C H 2 + 10 O U T / C H 2 11 12 + P R E S U B • G N D 13 14 15 16 G N D I N / C H 1 N F / C H 1 S T A N D | B Y 17 18 19 N F / C H 2 I N / C H 2 I N / C H 3 N F / C H 3 O U T / C H 3 + O U T / C H 3 - 2ch classH/2.00mm O U T / C H 2 + 10 O U T / C H 2 11 12 + P R E S U B • G N D 13 14 15 16 G N D I N / C H 1 N F / C H 1 S T A N D | B Y 17 18 19 20 21 22 23 N F / C H 2 I N / C H 2 3ch classH/2.00mm O U T / C H 2 + O U T / C H 2 + P R E S U B • G N D G N D I N / C H 1 N F / C H 1 S T A N D | B Y N F / C H 2 I N / C H 2 I N / C H 3 N F / C H 3 O U T / C H 3 + O U T / C H 3 - No. A1248-6/11 STK433-090-E Evaluation Board Characteristics Total power dissipation within the board, Pd - W 100 7 5 3 2 THD - PO VCC=±33V VG=30dB RL=6Ω 2ch Drive Rg=600Ω Tc=25°C 120 Pd - PO VCC=±33V VG=30dB f=1kHz Rg=600Ω Tc=25°C RL=6Ω 2ch Drive (same output rating) Total harmonic distortion, THD - % 10 7 5 3 2 1.0 7 5 3 2 0.1 7 5 3 2 0.01 7 5 3 2 0.001 0.1 100 80 60 f=20kHz 40 f=1kH z 20 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100 ITF02640 0 0.1 23 5 7 1.0 23 5 7 10 23 5 7 100 23 5 71000 ITF02641 Output power, PO/ch - W 120 Output power, PO/ch - W 120 PO - VCC PO - f 100 Output power, PO/ch - W Output power, PO/ch - W 80 f=1kHz RL=6Ω 2ch Drive VG=30dB Rg=600Ω 100 THD=10% 80 TH D= 1 D =0 0% .4 % THD=0.4% 60 60 TH 40 40 20 20 0 10 20 30 40 50 ITF02642 Supply voltage, VCC - ±V 0 10 VCC=±33V VG=30dB Rg=600Ω Tc=25°C RL=6Ω 2ch Drive 23 5 7 100 23 5 7 1k 23 5 7 10k 23 5 7100k ITF02643 Frequency, f - Hz [Thermal Design Example for STK433-090-E (RL = 6Ω)] The thermal resistance, θc-a, of the heat sink for total power dissipation, Pd, within the hybrid IC is determined as follows. Condition 1: The hybrid IC substrate temperature, Tc, must not exceed 125°C. Pd × θc-a + Ta < 125°C ................................................................................................. (1) Ta: Guaranteed ambient temperature for the end product Condition 2: The junction temperature, Tj, of each power transistor must not exceed 150°C. Pd × θc-a + Pd/N × θj-c + Ta < 150°C .......................................................................... (2) N: Number of power transistors θj-c: Thermal resistance per power transistor However, the power dissipation, Pd, for the power transistors shall be allocated equally among the number of power transistors. The following inequalities result from solving equations (1) and (2) for θc-a. θc-a < (125 − Ta)/Pd ...................................................................................................... (1)' θc-a < (150 − Ta)/Pd − θj-c/N ........................................................................................ (2)' Values that satisfy these two inequalities at the same time represent the required heat sink thermal resistance. When the following specifications have been stipulated, the required heat sink thermal resistance can be determined from formulas (1)' and (2)'. • Supply voltage VCC • Load resistance RL • Guaranteed ambient temperature Ta No. A1248-7/11 STK433-090-E [Example] When the IC supply voltage, VCC, is ±33V and RL is 6Ω, the total power dissipation, Pd, within the hybrid IC, will be a maximum of 75W at 1kHz for a continuous sine wave signal according to the Pd-PO characteristics. For the music signals normally handled by audio amplifiers, a value of 1/8PO max is generally used for Pd as an estimate of the power dissipation based on the type of continuous signal. (Note that the factor used may differ depending on the safety standard used.) This is: Pd ≈ 59.0W (when 1/8PO max. = 10W, PO max. = 80W). The number of power transistors in audio amplifier block of these hybrid ICs, N, is 4, and the thermal resistance per transistor, θj-c, is 2.1°C/W. Therefore, the required heat sink thermal resistance for a guaranteed ambient temperature, Ta, of 50°C will be as follows. From formula (1)' θc-a < (125 − 50)/59.0 < 1.27 From formula (2)' θc-a < (150 − 50)/59.0 − 2.1/4 < 1.17 Therefore, the value of 1.17°C/W, which satisfies both of these formulae, is the required thermal resistance of the heat sink. Note that this thermal design example assumes the use of a constant-voltage power supply, and is therefore not a verified design for any particular user’s end product. STK433-100 Series Standby Control, Mute Control, Load-short Protection & DC offset Protection application STK433-100 series -PRE -VCC +VCC Ch1 OUT Ch1 OUT Ch2 OUT Ch2 OUT +PRE SUB GND Ch1 IN Ch1 NF ST-BY Ch2 NF Ch2 IN (*1) The voltage applied to the Stand-by pin (#13) must not exceed the maximum rated value (VST max). 1 2 3 4 56kΩ 6.8kΩ 5 56kΩ 0.22Ω/2W 6 6.8kΩ 7 0.22Ω/2W 8 9 10 11 12 13 14 15 33kΩ 33μF /10V 1kΩ Stand-by Control (ex) H: Operation Mode (+5V) L: Stand-by Mode (0V) 2kΩ (*1) 13kΩ 56kΩ 56kΩ Ch2 IN Load short protection circuit 22kΩ 56kΩ Latch up circuit +VCC 0.1μF 1kΩ R1 (*1) 10kΩ 100kΩ GND Ch2 OUT 82kΩ GND -VCC GND 82kΩ Ch1 OUT DC offset protection ST-BY 22μF 22μF 100 kΩ Standby Control Mute Control +5V V1 2.2kΩ Mute Control H: Single Mute L: Normal 10kΩ 10kΩ 10kΩ GND Ch1 IN +5V MUTE PLAY MUTE ST-BY No. A1248-8/11 STK433-090-E STK433-100 Series Application Explanation STK433-100 series -PRE -VCC Stand-by Circuit in Pre Driver IC SW transistor ΔVBE Ch1 Ch2 Ch1 Ch2 +VCC OUT(+) OUT(-) OUT(+) OUT(-) +PRE SUB GND Ch1 IN Ch1 NF ST-BY Ch2 NF Ch2 IN 1) Stand-by control circuit part H: Operation mode (+5V) L: Stand-by mode (0V) 1kΩ 33kΩ 2kΩ 1 2 3 4 5 0.22Ω/2W 56kΩ 6 6.8kΩ 7 8 9 10 11 12 13 14 15 0.22Ω/2W 56kΩ 6.8kΩ IST (*1) R1 Tr5 ex) 13kΩ 33μF (*2) ex) +5V Tr1 Point.B 56kΩ Point.C Point.B Tr2 56kΩ Point.C 22kΩ 56kΩ I3 I2 Tr4 0.1μF 10kΩ 1kΩ (*4) R2 Tr3 100kΩ (2) Load short detection part (3) Latch-up circuit part -VCC 82kΩ OUT Ch1 OUT Ch2 82kΩ 22μF 22μF Tr5 Tr6 100 kΩ (4) DC offset protection The protection circuit application for the STK433-100sr consists of the following blocks (blocks (1) to (4)). (1) Standby control circuit block (2) Load short-circuit detection block (3) Latch-up circuit block (4) DC voltage protection block 1) Standby control circuit block (Reference example) STK433-100 series test circuit (when +5V is applied to Stand-by control.) 1kΩ (*3) 1) Stand-by control H: Operation mode (+5V) L: Stand-by mode (0V) VST ΔVBE Sink current IST 33μF (*2) 2kΩ (*3) (*1) R1 13kΩ 33kΩ 1 -PRE 2 -VCC 3 +VCC 4 Ch1 OUT 5 Ch1 OUT 6 Ch2 OUT 7 Ch2 OUT 8 +PRE 9 10 11 Ch1 IN 12 Ch1 NF ΔVBE 13 ST-BY 14 Ch2 NF 15 Ch2 IN SUB GND ex) Stand-by control voltage=+5V IST=(VST-VBE*2)/R1 =(5-0.6*2)/13kΩ ≈0.3(mA) STK433-100series Concerning pin 13 reference voltage VST Stand-by Circuit in Pre Driver IC Operation mode The switching transistor in the bias circuit turns on and places the amplifier into the operating mode when the current flowing into pin 13 (IST) becomes 0.25mA or greater. Standby mode When the current flowing into pin 13 (IST) is stopped (=0mA), the switching transistor in the bias circuit turns off, placing the amplifier into the standby mode. (*1) The current limiting resistor (R1) must be used to ensure that the current flowing into the stand-by pin (pin 13) does not exceed its maximum rated value IST max. (*2) The pop noise level when the power is turned on can be reduced by setting the time constant with a capacitor in operating mode. (*3) Determines the time constant at which the capacitor (*3) is discharged in standby mode. No. A1248-9/11 STK433-090-E 2) Load short-circuit detection block Since the voltage between point B and point C is less than 0.6V in normal operation mode (VBE < 0.6V) and TR1 (or TR2) is not activated, the load short-circuit detection block does not operate. When a load short-circuit occurs, however, the voltage between point B and point C becomes larger than 0.6V, causing TR1 (or TR2) to turn on (VBE > 0.6V), and current I2 to flows. 3) Latch-up circuit block TR3 is activated when I2 is supplied to the latch-up circuit. When TR3 turns on and current I3 starts flowing, VST goes down to 0V (standby mode), protecting the power amplifier. Since TR3 and TR4 configure a thyristor, once TR3 is activated, the IC is held in the standby mode. To release the standby mode and reactivate the power amplifier, it is necessary to set the standby control voltage (*2) temporarily low (0V). Subsequently, when the standby control is returned to high, the power amplifier will become active again. (*4) The I3 value varies depending on the supply voltage. Determine the value of R2 using the formula below, so that I1 is equal to or less than I3. I1 ≤ I3 = VCC/R2 4) DC offset protection block The DC offset protection circuit is activated when ±0.5V (typ) voltage is applied to either "OUT CH1" or "OUT CH2," and the hybrid IC is shut down (standby mode). To release the IC from the standby mode and reactivate the power amplifier, it is necessary to set the standby control voltage temporarily low (0V). Subsequently, when the standby control is returned to high (+5V, for example), the power amplifier will become active again. The protection level must be set using the 82kΩ resistor. Furthermore, the time constant must be determined using 22μ//22μ capacitors to prevent the amplifier from malfunctioning due to the audio signal. STK433-100 Series BTL Application STK433-100-E series Ch1 -PRE -VCC +VCC OUT Ch1 OUT Ch2 Ch2 OUT OUT +PRE SUB GND Ch1 IN Ch1 Ch2 Ch2 NF ST-BY NF IN (*1) The voltage applied to the Stand-by pin (#13) must not exceed the maximum rated value (VST max). 1 100Ω /1W 2 3 0.22Ω 4 5 0.22Ω 6 7 8 9 10 11 12 13 14 15 Stand-by Control 56kΩ 56kΩ 3pF 100μF /100V 100μF /100V 3pF 100Ω/1W 100pF (*1) R1 1.8kΩ 100μF /100V 10μF /10V 1.8kΩ 470pF 56kΩ 10μF /10V GND 1kΩ -VCC +VCC 33μF 33μF 56kΩ 3μH 0.1μF 3μH 4.7Ω 0.1μF 4.7Ω /1W 4.7Ω 2.2μF /50V Ch1 IN 4.7Ω/1W RL=8Ω OUT No. A1248-10/11 STK433-090-E SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. T his catalog provides information as of March, 2009. Specifications and information herein are subject to change without notice. PS No. A1248-11/11