LB1936V-MPB-E

Ordering number : EN7233A LB1936V Monolithic Digital IC 1-2 Phase Excitation Stepper Motor Driver http://onsemi.com Overview The LB1936V is a 2-phase bipolar drive stepper motor driver IC that supports low-voltage drive. The LB1936V's miniature package and minimal number of external components reduces the required mounting area. It also provides high-efficiency motor drive and can reduce circuit current consumption. Since it provides a current detection pin and supports PWM control input, it can be used to implement current chopper control at the system level. The LB1936V is optimal for the stepper motor drive in scanners, digital cameras, and printers. Features • Low saturation voltage forward/reverse motor driver (VO sat = 0.25V at IO = 200mA) • Two H-bridge channels • Wide usable voltage range (Allowable voltage range : 2.5V to 9.5V, absolute maximum rating : 10.5V) • Supports PWM input (Low power consumption can be achieved in slow delay mode that uses IN1/IN2 = H/H logic.) • Motor (coil) current detection pin • Built-in thermal shutdown circuit • Miniature package (SSOP16 : 225mil) Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Maximum output voltage Maximum input voltage Ground pin source current Allowable power dissipation Symbol Conditions Ratings Unit VCC max -0.3 to +10.5 VS max -0.3 to +10.5 V VS+ VSF V -0.3 to +8.0 V VOUT max VIN max IGND max Pd max V Per channel 800 mA When mounted on a circuit board * 740 mW Operating temperature Topr -20 to +85 °C Storage temperature Tstg -40 to +150 °C * Specified circuit board : 114.3 × 76.1 × 1.6mm3, glass epoxy Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. ORDERING INFORMATION See detailed ordering and shipping information on page 5 of this data sheet. Semiconductor Components Industries, LLC, 2013 September, 2013 90913NK /40407 TI PC B8-5595 No.7233-1/5 LB1936V Allowable Operating Range at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC 2.5 to 9.5 V VS 2.5 to 9.5 High-level input voltage VIH 2.0 to 7.5 V Low-level input voltage VIL -0.3 to 0.7 V Electrical Characteristics at Ta = 25°C, VCC = VS = 5V Parameter Symbol VCC system power supply current VS system power supply current Output saturation voltage Input current Ratings Conditions min typ Unit max ICC0 IN1 = IN2 = IN3 = IN4 = 0V 0.1 1 μA ICC1 IN1 = IN3 = 3V, IN2 = IN4 = 0V 10 16 mA IS0 IN1 = IN2 = IN3 = IN4 = 0V 0.1 1 μA IS1 IN1 = IN3 = 3V, IN2 = IN4 = 0V 12 19 mA VOUT1 VCC = VS = 3V to 7.5V, VIN = 3V or 0V, IOUT = 200mA (High and low side) - 0.25 0.4 V VOUT2 VCC = VS = 4V to 7.5V, VIN = 3V or 0V, IOUT = 400mA (High and low side) - 0.5 0.8 V 150 200 μA 30 μA 1.7 V IIN VIN = 5V Spark killer diode Reverse current IS(leak) Forward voltage VSF IOUT = 400mA Package Dimensions unit:mm (typ) 3178B 5.2 0.5 6.4 9 4.4 16 1 8 0.65 0.22 0.8 Specified circuit board : 114.3 × 76.1 × 1.6mm3 glass epoxy board Mounted on the specified circuit board 0.74 0.6 0.4 0.2 1.5max 0 -20 0 20 40 60 80 100 (1.3) Ambient temperature, Ta – °C 0.1 (0.33) 0.15 Allowable power dissipation, Pd max – W Pd max – Ta 1.0 SSOP16(225mil) No.7233-2/5 LB1936V Pin Assignment VS 1 16 P-GND VCC 2 15 RFG1 IN1 3 14 OUT1 IN2 4 13 OUT2 LB1936V S-GND 5 12 OUT3 IN3 6 11 OUT4 IN4 7 10 RFG2 VS 9 8 (NC) Top view Block Diagram 10μF VCC VS 30kΩ OUT1 IN1 Stepping Motor 10μF 30kΩ OUT2 IN2 30kΩ 30kΩ IN4 30kΩ RFG1 VS Thermal shutdown 30kΩ IN3 Control block 30kΩ OUT3 OUT4 30kΩ RFG2 S-GND P-GND LB1936V No.7233-3/5 LB1936V Truth Table IN1 IN2 L IN3 IN4 OUT1 OUT2 L off off (1) L H L H (2) H L H L off H (4) H(*) H(*) H off (4)′ - - OUT3 OUT4 Output mode (3) - L L off off (5) L H L H (6) H L H L (7) off H (8) H(*) H(*) H off (8)′ - L : low, H : high *: The output logic mode when IN1/IN2 = H/H is determined by the immediately preceding IN1/IN2 mode. The post-switching output modes will be as follows. When switching from (2): (4) When switching from (3): (4)' When switching from (1): Undefined (Either (4) or (4)') The modes when IN3/IN4 = H/H operate similarly as described below. When switching from (6): (8) When switching from (7): (8)' When switching from (5): Undefined (Either (8) or (8)') ICC -- VCC 15 10 5 0 0 1 2 3 4 5 IS -- VS 20 Supply current, IS – mA Supply current, ICC – mA 20 6 7 8 9 15 10 5 0 10 0 1 2 Supply voltage, VCC – V Output saturation voltage, VO(sat) – V Input current, IIN – µA 1 to N4 I 50 0 0 1 2 3 4 5 6 7 8 9 10 VO(sat) -- IO IN 100 5 0.8 200 150 4 Supply voltage, VS – V IIN -- VIN 250 3 6 Input voltage, VIN – V 7 8 9 0.7 0.6 0.5 e ow dl 0.4 gh Hi 0.3 sid an 0.2 0.1 0 0 100 200 300 400 500 600 Output current, IO – mA No.7233-4/5 LB1936V ICC -- Ta 10 5 0 -40 -20 0 20 40 60 80 100 120 140 Output saturation voltage, VO(sat) – V Ambient temperature, Ta – °C 10 5 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature, Ta – °C VO(sat) -- Ta 0.7 IS -- Ta 15 Supply current, Is – mA Supply current, ICC – mA 15 High and low side 0.6 0.5 0.4 0.3 0.2 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature, Ta – °C ORDERING INFORMATION Device LB1936V-MPB-E Package SSOP16 (225mil) ( Pb-Free ) LB1936V-TLM-E SSOP16 (225mil) ( Pb-Free ) Shipping (Qty / Packing) 90 / Fan-Fold 2000 / Tape & Reel ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.7233-5/5