3-107-924

DG11 Power entry modules without line filter https://www.schurter.com /PG05 IEC Appliance Inlet C14 or C18 with Circuit Breaker TA35 2-pole Screw-on with IP67 and TA35 in white with black printed symbols C14 Screw-on with IP67 Snap-in IP40 with TA35 red illuminated and embossed symbols C18 See below: Approvals and Compliances 70° C 70° C Description - Panel mount : Screw-on version from front or rear side, snap-in version from front side - 2 Functions : Appliance Inlet , protection class I or II , Circuit breaker type TA35 , 2-pole - Pre-wired coupling - V-Lock notch standard - Quick connect terminal 6.3 x 0.8 mm Unique Selling Proposition - Variant tested for IP67 into the appliance - Various mounting options - Recessed rocker prevents accidental manipulation - Compatible with V-Lock cord retention Technical Data Ratings IEC Ratings UL/CSA Dielectric Strength Allowable Operation Temperature IP-Protection Insulation cover Terminal Panel Thickness S Material: Housing Characteristics - Connector and circuit breaker are prewired - Circuit Breaker non-illuminated or illuminated - Suitable for use in equipment according to IEC/UL 60950 Other versions on request - Version without pre-wiring from inlet to circuit breaker - Protection class II, 70°C - Variants in white References Substitute for type   6135  Component: circuit breakers   TA35 Rocker 2Pole  Weblinks pdf datasheet, html-datasheet, General Product Information, DistributorStock-Check, Accessories, Detailed request for product, Microsite   10 A / 250 VAC; 50 Hz 15 A / 250 VAC; 60 Hz > 2.5 kVAC between L-N > 3 kVAC between L/N-PE (1 min/50 Hz) -25 °C to 60 °C from front side IP40 or IP67 acc. to IEC 60529 Suitable for appliances with protection class I or II acc. to IEC 61140 Quick connect terminals 6.3 x 0.8 mm Screw: max 8 mm Recommended torque min 0.25 Nm Snap-in : S =1/1.2/1.5/2/2.5/3 mm Thermoplastic, black, UL 94V-0 appliance inlet/-outlet Circuit Breakers C14 / C18 acc. to IEC 60320-1 UL 60320-1, CSA C22.2 no. 60320-1 (for cold conditions) pin-temperature 70 °C, 10 A, Protection Class I or II Acc. IEC/EN 60934, UL 1077, CSA 22.2 no. 235 2-pole rocker switch, illuminated or nonilluminated. Conditional short circuit Inc: 2000 A Approvals and Compliances Detailed information on product approvals, code requirements, usage instructions and detailed test conditions can be looked up in   Details about Approvals Connectors 1 DG11 Power entry modules without line filter https://www.schurter.com /PG05 Approvals The approval mark is used by the testing authorities to certify compliance with the safety requirements placed on electronic products. Approval Reference Type: DG11 Approval Logo Certificates Certification Body Description VDE Approvals VDE Certificate Number: 40048151 UL Approvals UL UL File Number: E96454 CQC Approvals CQC CCC Certificate Number: pending Design Standard Description Designed according to IEC 60320-1 Appliance couplers for household and similar general purposes Designed according to UL 60320-1 Standard for Attachment Plugs and Receptacles Designed according to CSA C22.2 no. 60320-1 General Use Receptacles, Attachment Plugs, and Similar Wiring Devices Design Standard Description Designed for applications acc. IEC/UL 60950 IEC 60950-1 includes the basic requirements for the safety of information technology equipment. Details Initiator Description CE declaration of conformity SCHURTER AG The CE marking declares that the product complies with the applicable requirements laid down in the harmonisation of Community legislation on its affixing in accordance with EU Regulation 765/2008. RoHS SCHURTER AG EU Directive RoHS 2011/65/EU China RoHS SCHURTER AG The law SJ / T 11363-2006 (China RoHS) has been in force since 1 March 2007. It is similar to the EU directive RoHS. REACH SCHURTER AG On 1 June 2007, Regulation (EC) No 1907/2006 on the Registration, Evaluation, Authorization and Restriction of Chemicals 1 (abbreviated as "REACH") entered into force. MicrositeV-Lock SCHURTER AG V-Lock system are based on a matching plug-dose combination. The connector is equipped with a notch intended for use with the latching cordset. The cord latching system prevents against accidental removal of the cordset. Product standards Product standards that are referenced Organization Application standards Application standards where the product can be used Organization Compliances The product complies with following Guide Lines Identification Dimensions [mm] Snap-in mounting for front mount IP40 (51.6) 35 5.65 48.3 30 ±0.10 22.1 63 59 +0.20 0 16 5.35 R1.5 x. ma +0.10 0 S 32.45 S = Panel thickness 2 Connectors 3.3 R3 DG11 Power entry modules without line filter https://www.schurter.com /PG05 Screw-on mounting version A for front mount IP40 5.65 (51.6) 30 +0.20 0 22.1 ø 6.2 ø 3.4 35 ±0.10 59 66 76 16 R 5.35 3.3 ±0.10 48.3 66 1.5 max. R3 ø 3.4/M3 1.2 32.45 Screw-on mounting Version A for rear mount IP40 (51.6) 5.65 50.1 59.2 ±0.10 ±0.10 22.1 57.2 66 76 16 R 5.35 ±0.10 1.5 66 ø 3.4 1 .R ax 1.8 35 34.25 ø 3.4/M3 m 1.5 Screw-on mounting Version B for front mount IP40 5.65 48.3 30 ±0.10 16 22.1 59 63 1.2 ±0.10 ø 3.4 / M3 ø 6.2 5.35 38 +0.20 0 (51.6) 48 x ma 3.3 3 32.45 .R .5 R1 38 Connectors 3 DG11 Power entry modules without line filter https://www.schurter.com /PG05 Screw-on mounting version B for rear mount IP40 5.65 (51.6) 38 ±0.10 5.35 29.2 ±0.10 57.2 ±0.10 22.1 63 16 ø 3.4 50.1 ø 3.4 / M3 48 m R1 ax .R 1.8 .5 38 34.25 1 1.5 Screw-on mounting for front mount IP67 (53.6) 5.65 ±0.10 22.1 38 68 38 +0.20 34.3 ±0.10 16 5.35 59 0 50.3 ø 3.4/M3 51 L L' P1 2) PE PE' TA35 1) N N' P2 1) Line 2) Load Effect of ambient temperature The units are calibrated for an ambient temperature of +23°C. To determine the rated current for a lower or higher ambient temperature, use a correction factor (typical value) from the table below: Ambient Temperature [°C] Correction factor -30 0.76 -20 0.81 0 0.90 +23 1.00 +40 1.03 +50 1.04 +60 1.06 Example: Rated current = 5 A, Environmental temperature = 50 °C --> Correction factor = 1.04, Resulting current = 5.2 A --> Fount to next higher rated current: 6 A 4 Connectors 3 Diagrams 42 ±0.10 .R 3.3 ax m 32.45 42 DG11 Power entry modules without line filter https://www.schurter.com /PG05 Time-Current-Curves [ min ] [ sec ] 10'000 60 30 20 10 [ min ] [ sec ] 10'000 Typ p TA35 3–15A (TC-1, TC-2) 5 200 1 Typ Nennstrom Umgebungstemp. 60 50 20 10 100 1 50 20 10 5 5 2 2 1 1 0,5 0,5 0,3 0,3 0,2 0,2 0,1 0,1 1,05 1,35 2 3 4 5 8 10 1,05 1,35 Multiple of Rated Current In Multiple of Rated Current In Reference Temperature +23° Reference Temperature +23° 2 3 Connectors 4 5 8 10 5 DG11 Power entry modules without line filter https://www.schurter.com /PG05 ORDER CODE Table 1 Selection for type TA35 Switch Switch 1 2 LINE LINE LOAD LOAD CBT without illumination illuminated Order example 2-pole Number of switched poles Number of protected poles C32 C34 Colours W B 3 4 6 Rocker black black black black black non-illuminated illuminated white black – – – – – red transparent green transparent orange transparent Other colours on request Rocker legend 0 K printed L printed l M printed OFF OFF printed white 0 l H Colour of print white 0 embossed l F ON Illustration ON Surface black black Other legends on request Position of the rocker legend e.g. I / O Rated current In (A) In Code In Code 1,0 2,0 4,0 5,0 6,0 J10 J20 040 050 060 8,0 10,0 12,0 15,0 080 100 120* 150* Other rated currents on request 6 Connectors W F 120 C0 No other features Other versions on request Switch front CBD CBD C12 C14 240 V 120 V TA35- *) UL / CSA only DG11 Power entry modules without line filter https://www.schurter.com /PG05 Configuration Code Typ DG11 Configuration Code (Example) TA35 C B D W F 1 2 0 C 0 -000- C6135-X X X - X X X -00 see table 1 Please note that Schurter will establish an internal part number for logistics use in addition to the order code. The format of this internal part number is, for example: 3-XXX-XXX Color 0 Black Panel Mounting 1) 00 Screw version A front mounting 01 Screw version B front mounting 02 Screw version A rear mounting 03 Screw version B rear mounting 10 Snap-in 1.0 mm 12 Snap-in 1.2 mm 15 Snap-in 1.5 mm 20 Snap-in 2.0 mm 25 Snap-in 2.5 mm 30 Snap-in 3.0 mm 88 Screw version front mounting (sealed towards housing, IP65) Terminal PE 0 Without (PCII) 1 QC 6.3x0.8 mm Terminal N 1 QC 6.3x0.8 mm (unwired) 3 Connection to TA35 (wired) Terminal L 1 QC 6.3x0.8 mm (unwired) 3 Connection to TA35 (wired) 1) Screw version A Screw version B All Variants Config. Code Order Number DG11-C126F100C0-000-C6135-331-200-00 3-107-924 █ DG11-CBDWM100C0-000-C6135-331-880-00 3-108-454 █ DG11-CBDBL100C0-000-C6135-331-010-00 3-108-463 █ DG11-CBDWM100C0-000-C6135-331-150-00 3-109-713 █ DG11-CBDWM100C0-000-C6135-331-010-00 3-109-714 █ DG11-CBDWM100C0-000-C6135-331-020-00 3-109-715 █ DG11-CBDWM150C0-000-C6135-331-150-00 3-109-716 █ DG11-CBDWM150C0-000-C6135-331-010-00 3-109-717 █ DG11-CBDWM150C0-000-C6135-331-020-00 3-109-718 █ DG11-CBDWM150C0-000-C6135-331-880-00 3-109-719 █ █ Most Popular. Availability for all products can be searched real-time:https://www.schurter.com/en/Stock-Check/Stock-Check-SCHURTER 10 Pcs  23.07.2018 Packaging unit   The specifications, descriptions and illustrations indicated in this document are based on current information. All content is subject to modifications and amendments. Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability and test each product selected for their own applications. Connectors 7