TA35-CBD6K150C0

Power entry modules without line filter www.schurter.com/pg05 IEC Appliance Inlet C14 with Circuit Breaker TA35 2-pole 635 C14 70° C Description - Panel Mount: Snap-in version from front side - 2 Functions: Appliance Inlet, Protection class I, Circuit breaker type TA35, 2-pole - Quick connect terminal 6.3 x 0.8 mm - Alternative: version for 16 A (20 A) 6136 - Substitute for type 7764 Characteristics - Unwired - Switch non-illuminated or illuminated Thermal overload protection - Qualified for use in equipment according IEC/EN 60950 Other versions on request Approvals - Pre-wired version - Quick-connect terminals 4.8 x 0.8 mm - Protection class II, 70°C - VDE License Number: 40023066 - UL License Number: E96454 References Weblinks General Product Information Approvals, RoHS, CHINA-RoHS, Mating Connectors, Distributor-StockCheck, Accessories Technical Data Ratings IEC Ratings UL/CSA Dielectric Strength 10 A / 250 VAC; 50 Hz 15 A / 250 VAC; 60 Hz > 2.5 kVAC between L-N > 3 kVAC between L/N-PE (1 min/50 Hz) -25 °C to 60 °C from front side IP 40 acc. to IEC 60529 Suitable for appliances with protection class 1 acc. to IEC 61140 Quick connect terminals 6.3 x 0.8 mm Snap-in1.5/2/2.5/3 mm Thermoplastic, black, UL 94V-0 Appliance Inlet C14 acc. to IEC/EN 60320-1 UL 498, CSA C22.2 no. 42 (for cold conditions) pin-temperature 70 °C, 10 A, Protection Class 1 Acc. IEC/EN 60934, UL 1077, CSA 22.2 no. 235 2-pole rocker switch, illuminated or nonilluminated. Conditional short circuit Inc: 2000 A Circuit Breakers Allowable Operation Temp. Degree of Protection Protection Class Terminal Panel Thickness s Material: Housing Connectors  635 www.schurter.com/pg05 Dimensions 30 10.6 31.8 Power entry modules without line filter 65.4 mm 3.2 27.4 +0.20 0 58.8 x 27.2 65.4 6 max. R 0.2 R3 S ± 0.05 28.4 Diagrams L 1) PE N N' P2 1) Line 2) Load L' P1 2) PE' TA35  Connectors 59 +0.20 0 Power entry modules without line filter www.schurter.com/pg05 ORDER CODE Number of switched poles Number of protected poles 2-pole 1 LINE 635 Table 1 Selection for type TA35 Order example 2 LINE LOAD LOAD TA35- CBD W F 120 C0 Switch without illumination illuminated 240 V 120 V CBT CBD No other features Switch C12 C14 C32 C34 Other versions on request Colours Switch front W B 3 4 6 black black black black black Rocker non-illuminated illuminated white black – – – – – red transparent green transparent orange transparent Other colours on request Rocker legend Surface F H K L embossed printed printed printed Illustration 0 l Colour of print OFF OFF ON white black white black ON l l M printed Other legends on request Position of the rocker legend e.g. F 0 0 Rated current In (A) In 1,0 2,0 4,0 5,0 6,0 Code J10 J20 040 050 060 In 8,0 10,0 12,0 15,0 Code 080 100 120* 150* Other rated currents on request *) UL / CSA only Connectors 3 635 www.schurter.com/pg05 Technical data (continued) Circuit breaker Tripping characteristics In < 3 A [ min ] [ sec ] 10'000 Type p Rated current Ambient temp. TA35 3 ... 15 A [ min ] [ sec ] 10'000 Type Rated current Ambient temp. TA35 > 3–15A (TC-1, TC-2) +23 °C 60 30 20 10 5 200 100 1 50 2`000 1`000 500 60 30 20 10 5 200 100 1 50 2`000 1`000 500 20 10 5 2 1 0,5 Tr ipping time Tr ipping time 20 10 5 2 1 0,5 0,3 0,2 0,1 1,05 1,35 2 3 4 5 8 10 Multiple of rated current [ x In ] 0,3 0,2 0,1 1,05 1,35 2 3 4 5 8 10 Multiple of rated current [ x In ] The above tripping characteristics apply to symmetrical overloads on the two poles. At asymmetric overloads on two pole types the tripping current will be increased by factor 1.05 (TC-2). Effect of ambient temperature The unit is calibrated for an ambient temperature of +23 °C. To determine the rated current for lower or higher ambient temperature, use a correction factor from the table below. * Ambient temperature [°C] –25 –20 0 +23 +40 +50 +60 Correction factor 0.79 0.81 0.90 1.00 1.03 1.04 1.06 * Temperature must be measured at the rear of the breaker next to the terminals after equipment operating temperature has been reached. Example: Rated current at +23 °C Ambient temperature Correction factor Chosen rated current at +60 °C ambient temperature: 10 A +60 °C 1.06 10 A x 1.06 = 10.6 A Order code (Order example) Type Order code TA35 Wiring 1 wired 0 unwired 6135 CBDWF120C0 see table 1 .0210 Terminals 1 Quick connect 6.3 x 0.8 mm Mounting 2 Snap-in s = 1.5 mm 3 Snap-in s = 2.0 mm 4 Snap-in s = 2.5 mm 5 Snap-in s = 3.0 mm 0 Protection class 1 Please note that Schurter will establish an internal part number for logistics use in addition to the order code. The format of this internal part number is, for example: 6135.xxxx.xxxx Packaging unit 40 Pcs  Connectors Power entry modules without line filter www.schurter.com/pg05 Accessories Description 635 Assorted Covers Rear Cover 0859.0074 Cord retaining kits Cord retaining strain relief Flat head, A 4700.0001 Mating Outlets/Connectors Category / Description Appliance Outlet Overview complete IEC Appliance Outlet F, Screw-on Mounting, Front Side, Solder or Quick-connect Terminal IEC Appliance Outlet F, Snap-in Mounting, Front Side, Solder or Quick-connect Terminal Appliance Outlet further types to 6135 4787 4788 Connector Overview complete IEC Connector C15A, Rewireable, Straight IEC Connector C15A, Rewireable, Straight IEC Connector C15A, Rewireable, Angled IEC Connector C13, Rewireable, Angled IEC Connector C13, Rewireable, Angled Connector further types to 6135 Power Cord Overview complete Power Cord with IEC Connector C13, Angled Power Cord with IEC Connector C13, Angled Power Cord with IEC Connector C13, Angled Power Cord with IEC Connector C13, Angled Power Cord with IEC Connector C13 Power Cord further types to 6135 0311 3011 3012 3013 3020 ... 0102 0102-G 0112 4012 4013 ... The specifications, descriptions and illustrations indicated in this document are based on Connectors current information. All content is subject to modifications and amendments. 5