FR152G

FR151G THRU FR157G Elektronische Bauelemente VOLTAGE 50V ~ 1000V 1.5 AMP Glass Passivated Fast Recovery Rectifier RoHS Compliant Product A suffix of "-C" specifies halogen-free. DO-15 .140(3.6) .104(2.6) DIA. FEATURES . Low Forward Voltage Drop . High Current Capability . High Reliability . High Surge Current Capability . High Speed Switching .034(.9) .028(.7) DIA. 1.0(25.4) MIN. .300(7.6) .230(5.8) 1.0(25.4) MIN. MECHANICAL DATA . Case: Molded Plastic . Epoxy: UL 94V-0 Rate Flame Retardant . Lead: Axial Lead, Solder Able per MIL-STD-202, Method 208 Guaranteed Dimensions in inches and (millimeters) . Polarity: Color Band Denotes Cathode End . Mounting Position: Any . Weight: 0.40 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. O TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.5A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: FR151G FR152G FR153G FR154G FR155G FR156G FR157G UNITS 50 35 50 100 70 100 200 140 200 400 280 400 1.5 50 1. 3 5.0 100 600 420 600 800 560 800 1000 700 1000 V V V A A V 150 30 -65 +175 250 500 nS pF C 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 01-Jun-2007 Rev. A Page 1 of 2 FR151G THRU FR157G Elektronische Bauelemente VOLTAGE 50V ~ 1000V 1.5 AMP Glass Passivated Fast Recovery Rectifier RATING AND CHARACTERISTIC CURVES ( FR151G THRU FR157G ) FIG.1-TYPICAL FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 50 INSTANTANEOUS FORWARD CURRENT,(A) 1.8 1.5 1.2 0.9 0.6 0.3 Single Phase Half Wave 60Hz Resistive Or Inductive Load 0.375"(9.5mm) Lead Length 10 3.0 1.0 Tj=25 C Pulse Width 300us 1% Duty Cycle 0 20 40 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE ( C) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 50 0.1 .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLT AGE,(V) 40 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 30 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 20 10 (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 70 60 50 40 30 20 10 trr +0.5A | | | | | | | | 0 -0.25A JUNCTION CAPACITANCE,(pF) -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) http://www.SeCoSGmbH.com/ 01-Jun-2007 Rev. A Any changing of specification will not be informed individual Page 2 of 2