FR305G

FR301G ~ FR307G Elektronische Bauelemente VOLTAGE 50 ~ 1000 V 3.0 A, Glass Passivated Fast Recovery Rectifiers RoHS Compliant Product A suffix of “-C” specifies halogen & lead-free FEATURES Low forward voltage drop High current capability High reliability High surge current capability DO-27 C A B MECHANICAL DATA Glass Passivated Case: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Axial leads, solderable per MIL-STD-202, method 208 guaranteed Polarity: Color band denotes cathode end Mounting position: Any Weight: 1.1050 grams (approximately) D A REF. A B C D Millimeter Min. Max. 25.4 (TYP) 7.20 9.53 5.00 5.60 1.20 1.32 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25°C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, de-rate current by 20%. PART NUMBERS SYMBOL FR FR FR FR FR PARAMETERS 301 G 302 G 303 G 304 G 305 G FR 306 G FR 307 G UNITS TESTING CONDITIONS Recurrent Reverse Voltage (Max.) RMS Voltage (Max.) DC Blocking Voltage (Max.) Instantaneous Forward Voltage(Max.) Average Forward Rectified Current (Max.) VRRM VRMS VDC VF IO 50 35 50 100 70 100 200 140 200 400 280 400 1.3 3.0 600 420 600 800 560 800 1000 700 1000 V V V V A IF = 3A 0.375” (9.5mm) lead length @ TA = 75°C 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Peak Forward Surge Current IFSM 80 5.0 150 150 60 -65 ~ 150 250 500 A DC Reverse Current (Max.) Reverse Recovery Time (Max.) Junction Capacitance (Typ.) Storage Temperature Range IR TRR CJ TSTG μA nS pF °C VR = VDC, TA=25°C VR=VDC, TA=100°C IF=0.5A, IR=1.0A, IRR=0.25A f=1MHz and applied 4V DC reverse voltage http://www.SeCoSGmbH.com/ Any changes of specification will not be informed individually. 01-April-2009 Rev. B Page 1 of 2 FR301G ~ FR307G Elektronische Bauelemente VOLTAGE 50 ~ 1000 V 3.0 A, Glass Passivated Fast Recovery Rectifiers RATINGS AND CHARACTERISTIC CURVES (FR301G THRU FR307G) FIG.1-TYPICAL FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 50 INSTANTANEOUS FORWARD CURRENT,(A) 3.0 2.5 2.0 1.5 1.0 0.5 0 Single Phase Half Wave 60Hz Resistive Or Inductive Load 0.375"(9.5mm) Lead Length 10 3.0 1.0 Tj=25 C Pulse Width 300us 1% Duty Cycle 0 20 40 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE,( C) 0.1 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 250 .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLT AGE,(V) 200 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 150 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 100 50 (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 140 120 100 80 60 40 20 0 trr +0.5A | | | | | | | | 0 -0.25A -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm JUNCTION CAPACITANCE,(pF) .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) http://www.SeCoSGmbH.com/ Any changes of specification will not be informed individually. 01-April-2009 Rev. B Page 2 of 2