SF61R

SF61R THRU SF67R Elektronische Bauelemente RoHS Compliant Product A suffix of "-C" specifies halogen-free VOLTAGE 50V ~ 600V 6.0AMP Super Fast Rectifiers R-6 FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application .360(9.1) .340(8.6) D IA. 1.0(25.4) MIN. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guaranteed * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 1.10 grams .360(9.1) .340(8.6) .052(1.3) .048(1.2) DIA. 1.0(25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 6.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: SF61R 50 35 50 SF62R SF63R SF64R SF65R SF66R SF67R UNITS 100 70 100 150 105 150 200 140 200 6.0 150 0.95 5.0 50 35 50 -65 +150 1.25 1.50 300 210 300 400 280 400 600 420 600 V V V A A V µA µA nS pF C 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 1 of 2 SF61R THRU SF67R Elektronische Bauelemente VOLTAGE 50V ~ 600V 6.0AMP Super Fast Rectifiers RATING AND CHARACTERISTIC CURVES (SF61R THRU SF67R) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) 6 5 4 3 2 1 0 0 25 50 75 100 125 150 175 Single Phase Half Wave 60Hz Resistive Or Inductive Load 0.375"(9.5mm) Lead Length FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A | | | | | | | | (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 -0.25A NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm AMBIENT TEMPERATURE,( C) FIG.3-TYPICAL FORWARD CHARACTERISTICS 50 INSTANTANEOUS FORWARD CURRENT,(A) FIG.4-TYPICAL REVERSE CHARACTERISTICS 50 3.0 ~SF 64R SF6 1R REVERSE LEAKAGE CURRENT, (mA) 10 10 3.0 1.0 Tj=100 C ~S 65R SF 1.0 F6 6R SF 67 R 0.1 Tj=25 C Pulse Width 300us 1% Duty Cycle Tj=25 C 0.1 .01 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 .01 0 20 40 60 80 100 120 140 FORWARD VOLT AGE,(V) PERCENT OF RATED PEAK REVERSE VOLT AGE,(%) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 150 FIG.6-TYPICAL JUNCTION CAPACITANCE 175 150 125 100 75 50 25 0 120 90 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 60 30 0 1 5 10 50 100 JUNCTION CAPACITANCE,(pF) .01 .05 .1 .5 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE,(V) http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 2 of 2