SMF1004D1

SMF1001D1 THRU SMF1007D1 VOLTAGE 50V ~ 1000V Elektronische Bauelemente 10.0AMP Surface Mount Fast Recovery Rectifiers RoHS Compliant Product A suffix of "-C" specifies halogen-free TO-252 FEATURES * Ideal for surface mount applications * Easy pick and place * Built-in strain relief * Fast switching speed 2 MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any 1 2 3 REF. P IN 1 PIN 3 PIN 2 CASE A B C D E F S Millimeter Min. Max. 6.40 6.80 5.20 5.50 6.80 7.20 2.20 2.80 2.30 REF. 0.70 0.90 0.60 0.90 REF. G H J K L M R Millimeter Min. Max. 0.50 0.70 2.20 2.40 0.45 0.55 0 0.15 0.90 1.50 5.40 5.80 0.80 1.20 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C (Per Leg 5.0A) Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 5.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Thermal Resistance, Juntion to Lead (Note 3) Thermal Resistance, Juntion to Ambient (Note 3) Operating and Storage Temperature Range TJ, TSTG SMF1001D1 SMF1002D1 SMF1003D1 SMF1004D1SMF1005D1SMF1006D1 SMF1007D1 UNITS 50 35 50 100 70 100 200 140 200 400 280 400 10.0 100 600 420 600 800 560 800 1000 700 1000 V V V A A V uA 1.3 1.5 10 0.5 250 44 8 30 -65 ~ +150 1.7 mA 500 nS pF C/W C 150 NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3. Rating applies when surface mounted on the minimum pad size recommended, PC Board with 8.0 X 8.0mm copper pad. http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 1 of 2 SMF1001D1 THRU SMF1007D1 VOLTAGE 50V ~ 1000V Elektronische Bauelemente 10.0AMP Surface Mount Fast Recovery Rectifiers RATING AND CHARACTERISTIC CURVES (SMF1001D1 THRU SMF1007D1) FIG.1-TYPICAL FORWARD 20 CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 12 10 8.0 6.0 4.0 2.0 0 0 Tj=25 C Pulse Width 300us 1% Duty Cycle Single Phase Half Wave 60Hz Resistive Or Inductive Load FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE INSTANTANEOUS FORWARD CURRENT,(A) SMF1001~SMF1004 SMF1005 10 5.0 SMF1006~SMF1007 1.0 20 40 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE ( C) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWAARD SURGE CURRENT,(A) 100 0.1 .01 .6 .8 1.2 1.4 1.6 1.8 2.0 2.2 FORWARD VOLT AGE,(V) 80 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 60 40 Tj=25 C 8.3ms Single Half Sine Wave 20 JEDEC method (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 35 30 25 20 15 10 5 trr +0.5A | | | | | | | | 0 -0.25A JUNCTION CAPACITANCE,(pF) -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 1 of 2