SMF15SS

SMF10SS THRU SMF15SS Elektronische Bauelemente VOLTAGE 1000V ~ 1500V 1.0AMP Surface Mount Fast Recovery Rectifiers RoHS Compliant Product A suffix of "-C" specifies halogen-free 2010 .181(4.60) FEATURES * Ideal for surface mount applications * High Voltage, Low profile package * Built-in strain relief * Fast switching speed 0.091(2.30) 0.083(2.10) .173(4.40) .002(0.05) 50 ) .0 R0 20 (0. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 0.063 grams 0.049(1.25) 0.033(0.85) 0.049(1.25) 0.033(0.85) 0.049(1.25) 0.033(0.85) * Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ , TSTG NOTES: SFM10SS 1000 800 1000 SFM12SS 1200 SFM15SS 1500 1200 1500 UNITS V V V 960 1200 1.0 25 1.3 5.0 10 0 500 15 -55 +155 A A V µA µA nS pF C 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.Marking Code: SMF10SS SMF12SS SMF15SS RGC10M RGC10Q RGC10Y http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 1 of 2 SMF10SS THRU SMF15SS Elektronische Bauelemente VOLTAGE 1000V ~ 1500V 1.0AMP Surface Mount Fast Recovery Rectifiers RATING AND CHARACTERISTIC CURVES (SMF10SS THRU SMF15SS) FIG.1-TYPICAL FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 50 INSTANTANEOUS FORWARD CURRENT,(A) 1.2 1.0 0.8 0.6 0.4 0.2 0 0 20 40 60 80 100 120 140 160 180 200 Single Phase Half Wave 60Hz Resistive Or Inductive Load 10 3.0 1.0 Tj=25 C Pulse Width 300us 1% Duty Cycle AMBIENT TEMPERATURE ( C) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWAARD SURGE CURRENT,(A) 50 0.1 .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLT AGE,(V) 40 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 30 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 20 10 (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 35 30 25 20 15 10 5 trr +0.5A | | | | | | | | 0 -0.25A JUNCTION CAPACITANCE,(pF) -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 2 of 2