1N4620D2A-JQRS

LOW NOISE ZENER DIODE 1N4620D2A / 1N4620D2B • • • • • • Low Leakage Low Current Low Noise Standard ±5% Zener Voltage Tolerance Hermetic Ceramic Surface Mount Package Space / High-Rel Screening Options Available ABSOLUTE ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise stated) PT TJ TSTG TSP TA = 25°C Total Power Dissipation at Junction Temperature Range Storage Temperature Range Maximum Soldering Pad Temperature for 20s 250mW -65 to +200°C -65 to +200°C 260°C E LECTRICAL ELECTRICAL CHARACTERISTICS (TA = 25°C, VF = 1.0V MAX @ IF = 200mA unless otherwise stated) Symbols S ymbol Symbols VZ ZZT IR ND IZM ɑVZ Parameters Parameters Zener Voltage Maximum Zener Impedance Reverse Current Noise Density Zener Current Temperature Coefficient † of Zener Voltage IZT = 250µA T1 = 25°C T2 = 100°C Test Conditions IZT = 250µA IZT = 250µA VR = 1.5V TA = 150°C IZT = 250µA Min 3.135 Typ 3.3 Max 3.465 1650 3.5 7.0 1.0 85 -0.075 Units Units V Ω µA µV Hz mA %/°C † Temperature coefficient of regulator voltage. The device shall be temperature stabilized with current applied prior to reading Zener voltage at the specified ambient temperature as specified. Verified by design. Not a production test. Semelab Limited reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. S emelab Semelab plc Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8864 Issue 1 Page 1 of 3 LOW NOISE ZENER DIODE 1N4620D2A / 1N4620D2B MECHANICAL DATA DLCC2 Variant A (D2A) PAD 1 PAD 2 DIMENSION A B C D ANODE CATHODE mm 5.00 ±0.10 2.61 ±0.10 1.08 ±0.10 1.76 ±0.10 Inches 0.197 ±0.004 0.103 ±0.004 0.043 ±0.004 0.069 ±0.004 DLCC2 Variant B (D2B) PAD 1 PAD 2 PAD 3 DIMENSION A B C D ANODE CATHODE LID CONTACT TO ANODE* mm 5.00 ±0.10 2.61 ±0.10 1.08 ±0.10 1.76 ±0.10 Inches 0.197 ±0.004 0.103 ±0.004 0.043 ±0.004 0.069 ±0.004 SOLDER PAD LAYOUT D-5A DLCC2/ D-5A MELF OVERLAY DIMENSION A B C mm 6.25 1.70 2.67 Inches 0.246 0.067 0.105 A B * The additional contact provides a connection to the lid in the application. Connecting the metal lid to a known electrical potential stops deep dielectric discharge in space applications; see the Space Weather link www.semelab.co.uk/dlcc2.html on the Semelab web site. Package variant to be specified at order. Other Package Outlines may be available – Contact Semelab Sales to Enquire S emelab Semelab plc Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8864 Issue 1 Page 2 of 3 C LOW NOISE ZENER DIODE 1N4620D2A / 1N4620D2B SCREENING OPTIONS Space Level (JQRS/ESA) and High Reliability options are available in accordance with the High Reliability and Screening Options Handbook available for download from the from the TT electronics Semelab web site. ESA Quality Level Products are based on the testing procedures specified in the generic ESCC 5000 and in the corresponding part detail specifications. Semelabs QR216 and QR217 processing specifications (JQRS), in conjunction with the companies ISO 9001:2000 approval present a viable alternative to the American MILPRF-19500 space level processing. QR217 (Space Level Quality Conformance) is based on the quality conformance inspection requirements of MIL-PRF19500 groups A (table V), B (table VIa), C (table VII) and also ESA / ESCC 5000 (chart F4) lot validation tests. QR216 (Space Level Screening) is based on the screening requirements of MIL-PRF-19500 (table IV) and also ESA /ESCC 5000 (chart F3). JQRS parts are processed to the device data sheet and screened to QR216 with conformance testing to Q217 groups A and B in accordance with MIL-STD-750 methods and procedures. Additional conformance options are available, for example Pre-Cap Visual Inspection, Buy-Off Visit or Data Packs. These are chargeable and must be specified at the order stage (See Ordering Information). Minimum order quantities may apply. Alternative or additional customer specific conformance or screening requirements would be considered. Contact Semelab sales with enquires. ORDERING INFORMATION Part numbers are built up from Type, Package Variant, and screening level. The part numbers are extended to include the additional options as shown below. Type – See Electrical Stability Characteristics Table Package Variant – See Mechanical Data Screening Level – See Screening Options (ESA / JQRS) Additional Options: Customer Pre-Cap Visual Inspection Customer Buy-Off visit Data Pack Solderability Samples Scanning Electron Microscopy Radiography (X-ray) Total Dose Radiation Test MIL-PRF-19500 (QR217) Group B charge Group B destructive mechanical samples Group C charge Group C destructive electrical samples Group C destructive mechanical samples ESA/ESCC Lot Validation Testing (subgroup 1) charge LVT1 destructive samples (environmental) LVT1 destructive samples (mechanical) Lot Validation Testing (subgroup 2) charge LVT2 endurance samples (electrical) Lot Validation Testing (subgroup 3) charge LVT3 destructive samples (mechanical) .CVP .CVB .DA .SS .SEM .XRAY .RAD .GRPB .GBDM (12 pieces) .GRPC .GCDE (12 pieces) .GCDM (6 pieces) .LVT1 .L1DE (15 pieces) .L1DM (15 pieces) .LVT2 .L2D (15 pieces) .LVT3 .L3D (5 pieces) Additional Option Notes: 1) All ‘Additional Options’ are chargeable and must be specified at order stage. 2) When Group B,C or LVT is required, additional electrical and mechanical destructive samples must be ordered 3) All destructive samples are marked the same as other production parts unless otherwise requested. MARKING DETAILS Parts can be laser marked with approximately 7 characters on two lines and always includes cathode identification. Typical marking would include part or specification number, week of seal or serial number subject to available space and legibility. Customer specific marking requirements can be arranged at the time of order. Example Marking: Example ordering information: The following example is for the 1N4620 part with package variant A, JQRS screening, additional Group C conformance testing and a Data pack. Part Numbers: 1N4620D2A-JQRS (Include quantity for flight parts) 1N4620D2A-JQRS.GRPC (chargeable conformance option) 1N4620D2A-JQRS.GCDE (charge for destructive parts) 1N4620D2A-JQRS.GCDM (charge for destructive parts) 1N4620D2A-JQRS.DA (charge for Data pack) Customers with any specific requirements (e.g. marking or screening) may be supplied with a similar alternative part number (there is maximum 20 character limit to part numbers). Contact Semelab sales with enquiries High Reliability and Screening Options Handbook link: http://www.semelab.co.uk/pdf/misc/documents/hirel_and_screening_options.pdf S emelab Semelab plc Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8864 Issue 1 Page 3 of 3