2N2857C1B-JQRS

SILICON RF SMALL SIGNAL NPN TRANSISTOR 2N2857C1 • • • • High Current Gain-Bandwidth Product (fT) Hermetic Ceramic Surface Mount Package Designed For High Gain, Low Noise Amplifier, Oscillator and Mixer Applications Screening Options Available ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise stated) VCBO VCEO VEBO IC PD PD TJ Tstg Collector – Base Voltage Collector – Emitter Voltage Emitter – Base Voltage Continuous Collector Current TA = 25°C Total Power Dissipation at Derate Above 25°C TC = 25°C Total Power Dissipation at Derate Above 25°C Junction Temperature Range Storage Temperature Range 30V 15V 3V 40mA 200mW 1.14mW/°C 300mW 1.72mW/°C -65 to +200°C -65 to +200°C THERMAL PROPERTIES Symbols RθJA RθJC Parameters Thermal Resistance, Junction To Ambient Thermal Resistance, Junction To Case Min. Typ. Max. 875 583.3 Units °C/W °C/W Semelab Limited reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. S emelab Coventry Road, Lutterworth, Leicestershire, LE17 4JB Semelab Limited Telephone +44 (0) 1455 556565 Fax +44 (0) 1455 552612 Email: sales@semelab-tt.com Document Number 7726 Issue 1 Page 1 of 4 Website: http://www.semelab-tt.com SILICON RF SMALL SIGNAL NPN TRANSISTOR 2N2857C1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise stated) Symbols V(BR)CEO (1) Parameters Collector-Emitter Breakdown Voltage Collector-Cut-Off Current Test Conditions IC = 3mA VCB = 15V IB = 0 IE = 0 TA = 150°C VCB = 30V IE = 0 IB = 0 IC = 0 VCE = 1.0V TA = -55°C IC = 10mA IC = 10mA IB = 1.0mA IB = 1.0mA Min 15 Typ Max Units V 10 1.0 1.0 100 10 30 10 0.4 150 nA µA nA µA ICBO ICES IEBO hFE (1) Collector-Cut-Off Current Emitter-Cut-Off Current Forward-current transfer ratio (1) VCE = 16V VEB = 3V IC = 3mA VCE(sat) VBE(sat) (1) Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage V 1.0 DYNAMIC CHARACTERISTICS | hfe | Small signal forward-current transfer ratio Small Signal Current Gain Collector – Base Feedback Capacitance (2) IC = 5mA f = 100MHz IC = 2mA f = 1.0KHz VCB = 10V f = 1.0MHz IE = 2mA f = 31.9MHz VCE = 6V f = 450MHz VCE = 6V f = 450MHz VCE = 6V VCE = 6V IE = 0 VCB = 6V IC = 1.5mA IC = 1.5mA RG = 50 10 21 hfe Ccb rb’CC Gpe 50 220 1.0 pF Collector Base Time Constant Small Signal Power Gain 4 15 ps 12.5 dB 4.5 NF (2) Noise Figure Notes Notes (1) Pulse Width ≤ 300us, δ ≤ 2% (2) By design only, not a production test. S emelab Coventry Road, Lutterworth, Leicestershire, LE17 4JB Semelab Limited Telephone +44 (0) 1455 556565 Fax +44 (0) 1455 552612 Email: sales@semelab-tt.com Website: http://www.semelab-tt.com Document Number 7726 Issue 1 Page 2 of 4 SILICON RF SMALL SIGNAL NPN TRANSISTOR 2N2857C1 MECHANICAL DATA Dimensions in mm (inches) 0.51 ± 0.10 (0.02 ± 0.004) 4 R0.31 (0.012) See Package Variant Table 0.76 ± 0.15 (0.03 ± 0.006) 1.02 ± 0.10 (0.04 ± 0.004) 2.54 ± 0.13 (0.10 ± 0.005) 2 1.91 ± 0.10 (0.075 ± 0.004) 3.05 ± 0.13 (0.12 ± 0.005) C1 R (0 0. .0 56 22 ) 1 3 0.31 (0.012) rad. 1.40 (0.055) max. Underside View PACKAGE VARIANT TABLE Variant C1A C1B Pad 1 Base Base Pad 2 Emitter Emitter Pad 3 Collector Collector Pad 4 No Pad (3-Pins Only) Lid Contact * * The additional contact provides a connection to the lid in the application. Connecting the metal lid to a known electrical potential stops deep dielectric discharge in space applications; see the Space Weather link www.semelab.co.uk/mil/lcc1_4 on the Semelab web site. Package variant to be specified at order. S emelab Coventry Road, Lutterworth, Leicestershire, LE17 4JB Semelab Limited Telephone +44 (0) 1455 556565 Fax +44 (0) 1455 552612 Email: sales@semelab-tt.com Website: http://www.semelab-tt.com Document Number 7726 Issue 1 Page 3 of 4 SILICON RF SMALL SIGNAL NPN TRANSISTOR 2N2857C1 SCREENING OPTIONS Space Level (JQRS/ESA) and High Reliability options are available in accordance with the High Reliability and Screening Options Handbook available for download from the from the TT electronics Semelab web site. ESA Quality Level Products are based on the testing procedures specified in the generic ESCC 5000 and in the corresponding part detail specifications. Semelabs QR216 and QR217 processing specifications (JQRS), in conjunction with the companies ISO 9001:2000 approval present a viable alternative to the American MILPRF-19500 space level processing. QR217 (Space Level Quality Conformance) is based on the quality conformance inspection requirements of MIL-PRF19500 groups A (table V), B (table VIa), C (table VII) and also ESA / ESCC 5000 (chart F4) lot validation tests. QR216 (Space Level Screening) is based on the screening requirements of MIL-PRF-19500 (table IV) and also ESA /ESCC 5000 (chart F3). JQRS parts are processed to the device data sheet and screened to QR216 with conformance testing to Q217 groups A and B in accordance with MIL-STD-750 methods and procedures. Additional conformance options are available, for example Pre-Cap Visual Inspection, Buy-Off Visit or Data Packs. These are chargeable and must be specified at the order stage (See Ordering Information). Minimum order quantities may apply. Alternative or additional customer specific conformance or screening requirements would be considered. Contact Semelab sales with enquires. ORDERING INFORMATION Part number is built from part and screening level. The part number can be extended to include the additional options as shown below. Type – See Electrical Stability Characteristics Table Package Variant – See Mechanical Data Screening Level – See Screening Options (ESA / JQRS) Additional Options: Customer Pre-Cap Visual Inspection Customer Buy-Off visit Data Pack Solderability Samples Scanning Electron Microscopy Radiography (X-ray) Total Dose Radiation Test MIL-PRF-19500 (QR217) Group B charge Group B destructive mechanical samples Group C charge Group C destructive electrical samples Group C destructive mechanical samples ESA/ESCC Lot Validation Testing (subgroup 1) charge LVT1 destructive samples (environmental) LVT1 destructive samples (mechanical) Lot Validation Testing (subgroup 2) charge LVT2 endurance samples (electrical) Lot Validation Testing (subgroup 3) charge LVT3 destructive samples (mechanical) .CVP .CVB .DA .SS .SEM .XRAY .RAD .GRPB .GBDM (12 pieces) .GRPC .GCDE (12 pieces) .GCDM (6 pieces) .LVT1 .L1DE (15 pieces) .L1DM (15 pieces) .LVT2 .L2D (15 pieces) .LVT3 .L3D (5 pieces) Additional Option Notes: 1) All ‘Additional Options’ are chargeable and must be specified at order stage. 2) When Group B,C or LVT is required, additional electrical and mechanical destructive samples must be ordered 3) All destructive samples are marked the same as other production parts unless otherwise requested. MARKING DETAILS Parts are typically marked with specification number, serial number (or week of seal) as shown in the example below. Customer specific marking requirements can be arranged at time of order but is approximately limited to two lines of 7 Characters. This is to ensure text remains readable.. Example Marking: Example ordering information: The following example is for the variant B package with, JQRS screening, additional Group C conformance testing and a Data pack. Part Numbers: 2N2857C1B-JQRS (Include quantity for flight parts) 2N2857C1B-JQRS.GRPC (chargeable conformance option) 2N2857C1B-JQRS.GCDE (charge for destructive parts) 2N2857C1B-JQRS.GCDM (charge for destructive parts) 2N2857C1B-JQRS.DA (charge for Data pack) Customers with any specific requirements (e.g. marking, package or screening) may be supplied with a similar alternative part number (there is maximum 20 character limit to part numbers). Requirements for deep dielectric discharge variant (C1B) must be specified at time of order. Contact Semelab sales with all enquiries High Reliability and Screening Options Handbook link: http://www.semelab.co.uk/pdf/misc/documents/hirel_and_screening_options.pdf S emelab Coventry Road, Lutterworth, Leicestershire, LE17 4JB Semelab Limited Telephone +44 (0) 1455 556565 Fax +44 (0) 1455 552612 Email: sales@semelab-tt.com Document Number 7726 Issue 1 Page 4 of 4 Website: http://www.semelab-tt.com