2N2919

2N2919 MECHANICAL DATA Dimensions in mm (inches) 8.51 (0.335) 9.40 (0.370) 7.75 (0.305) 8.51 (0.335) 6.10 (0.240) 6.60 (0.260) DUAL NPN PLANAR TRANSISTORS IN TO77 PACKAGE 1.02 (0.040) Max. 12.7 (0.500) Min. 0.41 (0.016) 0.53 (0.021) 5.08 (0.200) 2.54 (0.100) Applications • Differential Amplifiers 0.74 (0.029) 1.14 (0.045) 2.54 (0.100) 3 2 4 5 6 • High Gain, Low Noise Audio Amplifiers • Low Level Flip Flops • Transducer Signal Conditioner Amplifiers 1 45˚ 0.71 (0.028) 0.86 (0.034) TO–77 PACKAGE (MO - 002AF) Underside View PIN 1 – Collector 1 PIN 2 – Base 1 PIN 3 – Emitter 1 PIN 4 – Emitter 2 PIN 5 – Base 2 PIN 6 – Collector 2 ABSOLUTE MAXIMUM RATINGS (Tamb = 25°C unless otherwise stated) VCBO VCEO VEBO IC PD PD TSTG TL Collector – Base Voltage Collector – Emitter Voltage Emitter – Base Voltage Continuous Collector Current Total Device Dissipation Total Device Dissipation EACH SIDE TOTAL DEVICE 60V 60V 6V 30mA 300mW 500mW 1.72mW / °C 2.86W / °C 750mW 1.5W 4.3mW / °C 8.6mW / °C –65 to 200°C 300°C TAMB = 25°C Derate above 25°C TC = 25°C Derate above 25°C Storage Temperature Range Lead temperature (Soldering, 10 sec.) Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 3302 Issue 1 2N2919 ELECTRICAL CHARACTERISTICS (Tamb = 25°C unless otherwise stated) Parameter Test Conditions 1 IE = 0 IB = 0 IC = 0 IE = 0 TA = 150°C VCE = 5V VEB = 5V VCE = 5V hFE DC Current Gain VCE = 5V VCE = 5V VBE VCE(sat) hib hob |hfe| Cobo Base – Emitter Voltage Collector – Emitter Saturation Voltage Small Signal Common – Base Input Impedance Small Signal Common – Base Output Admittance Small Signal Common – Base Current Gain Common – Base Open Circuit Output Capacitance * Pulse Test: tp = 300µs , δ ≤ 1%. Parameter hFE1 hFE2 Test Conditions IC = 100µA IC = 100µA IC = 10µA to 1mA IC = 100µA TA2 = –55°C IC = 100µA TA2 = +125°C Min. Typ. Max. Unit VCE = 5V IB = 100µA VCB = 5V f = 1kHz VCB = 5V f = 1kHz VCE = 5V f = 20MHz VCB = 5V IE = 0 f = 140kHz to 1MHz IC = 500µA 3 6 IC = 1mA IB = 0 IC = 0 IC = 10µA TA = –55°C IC = 100µA IC = 1mA IC = 100µA IC = 1mA IC = 1mA 25 60 15 100 150 0.70 0.35 32 1 V Ω µmho — pF Min. 60 60 6 2 10 2 2 240 — nA µA nA V Typ. Max. Unit INDIVIDUAL TRANSISTOR CHARACTERISTICS IC = 10µA V(BR)CBO Collector – Base Breakdown Voltage V(BR)CEO* V(BR)EBO ICBO ICEO IEBO Collector – Emitter Breakdown Voltage IC = 10mA Emitter – Base Breakdown Voltage Collector Cut-off Current Collector Cut-off Current Emitter Cut-off Current IE = 10µA VCB = 45V TRANSISTOR MATCHING CHARACTERISTICS Static Forward Current Gain VCE = 5V Balance Ratio See Note 2. VCE = 5V VCE = 5V VCE = 5V TA1 = +25°C VCE = 5V TA1 = +25°C 0.9 1 3 5 0.8 — |VBE1 – VBE2| Base – Emitter Voltage Differential |∆(VBE1 – VBE2)∆TA| Base – Emitter Voltage Differential Change With Temperature mV mV 1 NOTES 1) Terminals not under test are open circuited under all test conditions. 2) The lower of the two readings is taken as hFE1. Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 3302 Issue 1