LT1084MIG-XX

LAB FEATURES INPUT SAFE AREA PROTECT ION SEME LT1084M MILITARY VERSION 5 AMP POSITIVE VOLTAGE REGULATOR • • • • • • • Low Dropout Performance Fixed or Adjustable Voltages Fixed Output Voltages of 3.3V, 5V & 12V Adjustable Output Voltage Range From 1.2V Line Regulation 0.015% / V Typical. Load Regulation 0.01% Typical. Available in Hermetically Sealed TO–3, SMD1 and TO–257 (isolated & non-isolated) Packages. • Military Temperature Range (–55 to +150°C) DEVICE(1) LT1084MK–XX LT1084MG–XX LT1084MIG–XX LT1084MSM–XX PACKAGE TO–3 TO–257 Isolated TO–257 SMD1 CU RR EN T LIMITING AMPLIFIER L IM I T OU TPUT SEN SE T H E R M AL O V ER L O AD VOL T AGE REGUL ATION AMPLIFIER VR E F ADJUST DESCRIPTION The LT1084 voltage regulators are monolithic Note integrated circuits designed for use in applications 1) –XX = Voltage Option: 3.3, 5 or 12 requiring a well regulated positive output voltage –XX = Left blank for Adjustable Option. with low input-output differential voltage. Features include full power usage of up to 5A load current, internal current limiting and thermal shutdown. Safe area protection on the die is also included, providing protection of the series pass Darlington transistor under most conditions. The hermetically sealed TO–3 packages are utilised for high reliablitiy and low thermal resistance, whilst the SMD1 package is designed for surface mount applications. ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated) VIN PD RqJC RqJC RqJC TJ TSTG TLEAD Input – Output Voltage Differential Power Dissipation Thermal Resistance Junction To Case Thermal Resistance Junction To Case Thermal Resistance Junction To Case Operating Junction Temperature Range Storage Temperature Range Lead Temperature (for 10 sec.) Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk 35V Internally limited * TO–3 TO–3 SMD1 SMD1 TO–257 TO–257 Control Power Control Power Control Power Control Power 0.76°C / W 2.3°C / W 0.79°C / W 4.0°C / W 0.79°C / W 4.0°C / W –55 to 150°C –55 to 200°C –65 to 150°C 300°C Prelim. 7/00 * These ratings are only applicable for power dissipations of 30 Watts over a limited range of VIN – VOUT. Semelab plc. LAB ELECTRICAL CHARACTERISTICS Parameter SEME LT1084M MILITARY VERSION (TJ = 25°C Unless otherwise stated) 1,2 Output Voltage Test Conditions 3.3 VIN – VOUT = 6.3V IO = 10mA to 5A VIN – VOUT = 8V IO = 10mA to 5A VIN – VOUT = 15V IO = 10mA to 5A Min. IO = 10mA TJ = Over Temp IO = 10mA TJ = Over Temp IO = 10mA TJ = Over Temp IO = 10mA TJ = Over Temp TJ = 25°C TJ = Over Temp IO = 10mA TJ = 25°C TJ = Over Temp TJ = Over Temp TJ = Over Temp TJ = Over Temp TJ = Over Temp TJ = 25°C 3 3 3 3 3 3 3 3 3 3 Typ. 3.3 3.3 5 5 12 12 1.25 1.25 0.015 0.035 0.05 0.1 0.2 1.3 Max. 3.333 3.366 5.05 5.10 12.12 12.24 1.262 1.270 0.2 Unit 3.267 3.234 4.95 4.90 11.88 11.76 1.238 1.225 VO 4 Output Voltage 5 V 12 VREF 4 Reference Voltage ADJ. VIN – VOUT = VO + 3V IO = 10mA to 5A VIN – VOUT = 1.5 to 15V IO = 10mA VIN – VOUT = 1.5 to 35V TJ = Over Temp 3 V % REG(LINE) 4 Line Regulation 0.5 0.3 0.4 1.5 % REG(LOAD) VD ICL IQ 4 Load Regulation Dropout Voltage Current Limit Quiescent Current VIN – VOUT = 3V VIN – VOUT = 3V % V A mA %/W DVOUT , DVREF = 1% VIN – VOUT = 5V VIN – VOUT = 25V VIN – VOUT = 35V tp = 30ms TJ = 25°C TJ = Over Temp TJ = Over Temp VIN – VOUT = 5V TJ = Over Temp TJ = Over Temp TJ = 25°C 6 3 3 3 5.5 0.3 6.5 0.6 10 0.002 55 120 0.2 5 0.01 REG(THERM) Thermal Regulation IPIN Adjust Pin Current Adjust Pin Current Change Temperature Stability mA mA % DIPIN TS IO VN RA IO = 0.5A IO = 0.5A 0.5 Minimum Load Current RMS Output Noise 5 VIN – VOUT = 25V 3 5 0.003 10 mA %VO dB Ripple Rejection Ratio VIN – VOUT = 3V TJ = Over Temp 3 IO = 3A 60 75 Notes 1. Test Conditions unless otherwise stated: VIN = 1.5 to 35V, or Maximum Input, whichever is less. IO = 10mA to 5A. 2. These specifications are only applicable for power dissipations of 45 Watts over a limited range of VIN – VOUT. 3. Over Temp. = Over specified Junction Temperature Range (See Absolute Maximum Ratings). 4. Low duty cycle pulse test with Kelvin connections required. Changes in output voltage are covered under the specification for thermal regulation. 5. Bandwidth of 10Hz to 10kHz. 6. 120Hz input ripple, 15V = 64dB min. COUT (CADJ) = 25mF. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Prelim. 7/00 LAB K Package (TO–3) 40.01 (1.575) Max. 10.41 (0.410) 10.72 (0.422) SEME LT1084M MILITARY VERSION G & IG Packages (TO–257) 4.83 (0.190) 5.46 (0.215) 0.89 (0.035) 1.14 (0.045) 26.67 (1.050) Max. 1 0.4 1 (0.4 1) 1 0.9 2 (0.4 3) 4.47 (0.176) Rad. 2 Pls. 1 3.39 (0.5 27) 1 3.64 (0.5 37) 3.05 (0.120) Ø 3.30 (0.130) 11.43 (0.450) 6.35 (0.250) 1.09 (0.043) 0.97 (0.038) Dia. 30.40 (1.197) 29.90 (1.177) 12.19 (0.48) 11.18 (0.44) 1.63 (0.064) 1.52 (0.060) 12.70 (0.50) 19.05 (0.75) 22.23 (0.875) Max. 123 0.64 (0.025) 0.89 (0.035) 2.54 ± 0.08 (0.10 ± 0.003) 3.05 ± 0.08 (0.12 ± 0.003) SMD1 Package 2 11.18 (0.440) 10.67 (0.420) 4.09 (0.161) 3.84 (0.151) 2 Pls 4 .1 4 (0 .1 6 3 ) 3 .8 4 (0 .1 5 1 ) 3 .7 0 (0 .1 4 6 ) 3 .4 1 (0 .1 3 4 ) 0 .8 9 (0 .0 3 5 ) m in . 3 .7 0 (0 .1 4 6 ) 3 .4 1 (0 .1 3 4 ) 3 .6 0 (0 .1 4 2 ) M ax. 1 3 0 .7 6 (0 .0 3 0 ) m in . 1 1 0 .6 9 (0 .4 2 1 ) 1 0 .3 9 (0 .4 0 9 ) 2 16.97 (0.668) 16.87 (0.664) 9 .6 9 .3 1 1 .5 1 1 .2 7 (0 8 (0 8 (0 8 (0 .3 8 .3 6 .4 5 .4 4 1) 9) 6) 4) 1 6 .0 2 (0 .6 3 1 ) 1 5 .7 3 (0 .6 1 9 ) 1 6.3 8 (0 .64 5) 1 6.8 9 (0 .66 5) 0 .5 0 (0 .0 2 0 ) 0 .2 6 (0 .0 1 0 ) LT1084MK Pin 1 2 Fixed Adjustable COMMON ADJUST INPUT INPUT Case is OUTPUT Pin 1 2 3 LT1084MSM Fixed COMMON OUTPUT INPUT Adjustable ADJUST OUTPUT INPUT LT1084MG Pin 1 2 3 Fixed Adjustable COMMON ADJUST OUTPUT OUTPUT INPUT INPUT Case is OUTPUT Pin 1 2 3 LT1084MIG Fixed Adjustable COMMON ADJUST OUTPUT OUTPUT INPUT INPUT Case is ISOLATED Prelim. 7/00 Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk