SEMIX241DH16S

SEMiX241DH16s Absolute Maximum Ratings Symbol Chip IT(AV) ITSM i2t sinus 180° 10 ms 10 ms Tc = 85 °C Tc = 100 °C Tj = 25 °C Tj = 130 °C Tj = 25 °C Tj = 130 °C 240 200 2250 1900 25300 18000 1700 1600 1600 Tj = 130 °C Tj = 130 °C 100 1000 -40 ... 130 -40 ... 125 AC sinus 50Hz 1 min 1s 4000 4800 A A A A A2s A2s V V V A/µs V/µs °C °C V V Conditions Values Unit SEMiX 13 ® VRSM VRRM VDRM (di/dt)cr Bridge Rectifier Module (halfcontrolled) SEMiX241DH16s (dv/dt)cr Tj Module Tstg Visol Features • Terminal height 17 mm • Chips soldered directly to isolated substrate Characteristics Symbol Chip VT VT(TO) rT IDD;IRD tgd tgr tq IH IL VGT IGT VGD IGD Rth(j-c) Rth(j-c) Rth(j-c) Module Rth(c-s) Ms Mt a w 350 per chip per module to heat sink (M5) to terminals (M6) 3 2.5 0.04 5 5 5 * 9,81 K/W K/W Nm Nm m/s2 g Tj = 25 °C, IT = 300 A Tj = 130 °C Tj = 130 °C Tj = 130 °C, VDD = VDRM; VRD = VRRM Tj = 25 °C, IG = 1 A, diG/dt = 1 A/µs VD = 0.67 * VDRM Tj = 130 °C Tj = 25 °C Tj = 25 °C, RG = 33 Ω Tj = 25 °C, d.c. Tj = 25 °C, d.c. Tj = 130 °C, d.c. Tj = 130 °C, d.c. per thyristor per module sin. 180° per thyristor per module per thyristor per module 0.32 0.32 3 150 0.25 6 1 2 150 150 300 250 600 1.9 0.85 4 24 V V mΩ mA µs µs µs mA mA V mA V mA K/W K/W K/W K/W K/W K/W Conditions min. typ. max. Unit Typical Applications* • Input Bridge Rectifier for AC/DC motor control • Power supply DH © by SEMIKRON Rev. 29 – 05.03.2010 1 SEMiX241DH16s Fig. 4L: Power dissipation per module vs. direct current Fig. 4R: Power dissipation per module vs. case temperature Fig. 5: Recovered charge vs. current decrease Fig. 6: Transient thermal impedance vs. time Fig. 7: On-state characteristics Fig. 8: Surge overload current vs. time 2 Rev. 29 – 05.03.2010 © by SEMIKRON SEMiX241DH16s © by SEMIKRON Rev. 29 – 05.03.2010 3 SEMiX241DH16s Fig. 9: Gate trigger characteristics spring configuration SEMiX 13 This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, Chapter IX * The specifications of our components may not be considered as an assurance of component characteristics. Components have to be tested for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our personal. 4 Rev. 29 – 05.03.2010 © by SEMIKRON