SEMIX303GB12E4S

SEMiX303GB12E4s Absolute Maximum Ratings Symbol IGBT VCES IC ICnom ICRM ICRM = 3xICnom VCC = 800 V VGE ≤ 20 V VCES ≤ 1200 V Tj = 175 °C Tc = 25 °C Tc = 80 °C 1200 466 359 300 900 -20 ... 20 Tj = 150 °C 10 -40 ... 175 Tc = 25 °C Tc = 80 °C 338 252 300 IFRM = 3xIFnom tp = 10 ms, sin 180°, Tj = 25 °C 900 1485 -40 ... 175 Tterminal = 80 °C AC sinus 50Hz, t = 1 min 600 -40 ... 125 4000 V A A A A V µs °C A A A A A °C A °C V Conditions Values Unit SEMiX® 3s Trench IGBT Modules SEMiX303GB12E4s Features • Homogeneous Si • Trench = Trenchgate technology • VCE(sat) with positive temperature coefficient • High short circuit capability • UL recognized, file no. E63532 VGES tpsc Tj IF IFnom IFRM IFSM Tj Module It(RMS) Tstg Visol Inverse diode Tj = 175 °C Typical Applications* • AC inverter drives • UPS • Electronic Welding Characteristics Symbol IGBT VCE(sat) VCE0 rCE VGE(th) ICES Cies Coes Cres QG RGint td(on) tr Eon td(off) tf Eoff Rth(j-c) Conditions IC = 300 A VGE = 15 V chiplevel Tj = 25 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C VGE = 15 V VGE = 0 V VCE = 1200 V VCE = 25 V VGE = 0 V VGE = - 8 V...+ 15 V Tj = 25 °C VCC = 600 V IC = 300 A VGE = ±15 V RG on = 1.8  RG off = 1.8  di/dton = 5250 A/µs di/dtoff = 2825 A/µs per IGBT Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C min. typ. 1.8 2.2 0.8 0.7 3.3 5.0 max. 2.05 2.4 0.9 0.8 3.8 5.3 6.5 0.3 Unit V V V V m m V mA mA nF nF nF nC  ns ns mJ ns ns mJ Remarks • Case temperature limited to TC=125°C max. • Product reliability results are valid for Tj=150°C • Dynamic values apply to the following combination of resistors: RGon,main = 1,0  RGoff,main = 1,0  RG,X = 2,0  RE,X = 0,5  VGE=VCE, IC = 11.4 mA Tj = 25 °C Tj = 150 °C f = 1 MHz f = 1 MHz f = 1 MHz 5 5.8 0.1 18.5 1.22 1.03 1695 2.50 255 57 30 565 98 41.2 0.095 K/W GB © by SEMIKRON Rev. 1 – 05.01.2011 1 SEMiX303GB12E4s Characteristics Symbol Conditions Tj = 25 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C rF Tj = 25 °C Tj = 150 °C IF = 300 A Tj = 150 °C di/dtoff = 5100 A/µs T = 150 °C j VGE = -15 V Tj = 150 °C VCC = 600 V per diode 1.1 0.7 2.7 3.5 min. typ. 2.2 2.2 1.3 0.9 3.0 4.2 300 44.2 17.7 max. 2.52 2.5 1.5 1.1 3.4 4.6 Unit V V V V m m A µC mJ Inverse diode VF = VEC IF = 300 A VGE = 0 V chip VF0 SEMiX® 3s Trench IGBT Modules SEMiX303GB12E4s Features • Homogeneous Si • Trench = Trenchgate technology • VCE(sat) with positive temperature coefficient • High short circuit capability • UL recognized, file no. E63532 IRRM Qrr Err Rth(j-c) Module LCE RCC'+EE' Rth(c-s) Ms Mt w 0.18 20 K/W nH m m K/W res., terminal-chip per module to heat sink (M5) TC = 25 °C TC = 125 °C 3 to terminals (M6) 2.5 0.7 1 0.04 5 5 300 Nm Nm Nm g  K Typical Applications* • AC inverter drives • UPS • Electronic Welding Temperatur Sensor R100 B100/125 Tc=100°C (R25=5 k) R(T)=R100exp[B100/125(1/T-1/T100)]; T[K]; 493 ± 5% 3550 ±2% Remarks • Case temperature limited to TC=125°C max. • Product reliability results are valid for Tj=150°C • Dynamic values apply to the following combination of resistors: RGon,main = 1,0  RGoff,main = 1,0  RG,X = 2,0  RE,X = 0,5  GB 2 Rev. 1 – 05.01.2011 © by SEMIKRON SEMiX303GB12E4s Fig. 1: Typ. output characteristic, inclusive RCC'+ EE' Fig. 2: Rated current vs. temperature IC = f (TC) Fig. 3: Typ. turn-on /-off energy = f (IC) Fig. 4: Typ. turn-on /-off energy = f (RG) Fig. 5: Typ. transfer characteristic Fig. 6: Typ. gate charge characteristic © by SEMIKRON Rev. 1 – 05.01.2011 3 SEMiX303GB12E4s Fig. 7: Typ. switching times vs. IC Fig. 8: Typ. switching times vs. gate resistor RG Fig. 9: Typ. transient thermal impedance Fig. 10: Typ. CAL diode forward charact., incl. RCC'+EE' Fig. 11: Typ. CAL diode peak reverse recovery current Fig. 12: Typ. CAL diode recovery charge 4 Rev. 1 – 05.01.2011 © by SEMIKRON SEMiX303GB12E4s SEMiX 3s spring configuration This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, Chapter IX * The specifications of our components may not be considered as an assurance of component characteristics. Components have to be tested for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our staff. © by SEMIKRON Rev. 1 – 05.01.2011 5