SEMIX453GD12VC

SEMiX453GD12Vc Absolute Maximum Ratings Symbol IGBT VCES IC ICnom ICRM ICRM = 3xICnom VCC = 600 V VGE ≤ 15 V VCES ≤ 1200 V Tj = 175 °C Tc = 25 °C Tc = 80 °C 1200 673 513 450 1350 -20 ... 20 Tj = 125 °C 10 -40 ... 175 Tc = 25 °C Tc = 80 °C 516 385 450 IFRM = 3xIFnom tp = 10 ms, sin 180°, Tj = 25 °C 1350 2430 -40 ... 175 Tterminal = 80 °C AC sinus 50Hz, t = 1 min 600 -40 ... 125 4000 V A A A A V µs °C A A A A A °C A °C V Conditions Values Unit SEMiX® 33c VGES tpsc Tj IF IFnom Inverse diode SEMiX453GD12Vc Features • Homogeneous Si • VCE(sat) with positive temperature coefficient • High short circuit capability • UL recognised file no. E63532 Tj = 175 °C IFRM IFSM Tj Module It(RMS) Tstg Visol Typical Applications* • AC inverter drives • UPS • Electronic Welding Characteristics Symbol IGBT VCE(sat) VCE0 rCE VGE(th) ICES Cies Coes Cres QG RGint td(on) tr Eon td(off) tf Eoff Rth(j-c) Remarks • Case temperature limited to TC=125°C max. • Product reliability results are valid for Tj=150°C • Dynamic values apply to the following combination of resistors: RGon,main = 0,5  RGoff,main = 0,5  RG,X = 2,2  RE,X = 0,5  Conditions IC = 450 A VGE = 15 V chiplevel Tj = 25 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C VGE = 15 V VGE = 0 V VCE = 1200 V VCE = 25 V VGE = 0 V VGE = - 8 V...+ 15 V Tj = 25 °C VCC = 600 V IC = 450 A VGE = ±15 V RG on = 1.4  RG off = 1.4  di/dton = 6400 A/µs di/dtoff = 4000 A/µs du/dtoff = 6600 V/ µs per IGBT Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C min. typ. 1.75 2.2 0.94 0.88 1.8 2.9 max. 2.2 2.5 1.04 0.98 2.6 3.4 6.5 0.3 Unit V V V V m m V mA mA nF nF nF nC  ns ns mJ ns ns mJ VGE=VCE, IC = 18 mA Tj = 25 °C Tj = 150 °C f = 1 MHz f = 1 MHz f = 1 MHz 5.5 6 0.1 27.0 2.66 2.65 4950 1.67 470 72 39.8 665 109 54.4 0.067 K/W GD © by SEMIKRON Rev. 2 – 16.02.2011 1 SEMiX453GD12Vc Characteristics Symbol Conditions Tj = 25 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C rF Tj = 25 °C Tj = 150 °C IF = 450 A Tj = 150 °C di/dtoff = 6900 A/µs T = 150 °C j VGE = -15 V Tj = 150 °C VCC = 600 V per diode 1.1 0.7 1.4 2.3 min. typ. 2.1 2.1 1.3 0.9 1.9 2.6 425 78.8 32.7 max. 2.46 2.4 1.5 1.1 2.1 2.8 Unit V V V V m m A µC mJ Inverse diode VF = VEC IF = 450 A VGE = 0 V chip VF0 SEMiX® 33c IRRM Qrr Err Rth(j-c) Module LCE RCC'+EE' 0.12 20 K/W nH m m K/W SEMiX453GD12Vc Features • Homogeneous Si • VCE(sat) with positive temperature coefficient • High short circuit capability • UL recognised file no. E63532 res., terminal-chip per module to heat sink (M5) TC = 25 °C TC = 125 °C 3 to terminals (M6) 2.5 0.7 1 0.014 5 5 900 Rth(c-s) Ms Mt w Nm Nm Nm g  K Typical Applications* • AC inverter drives • UPS • Electronic Welding Temperatur Sensor R100 B100/125 Tc=100°C (R25=5 k) R(T)=R100exp[B100/125(1/T-1/T100)]; T[K]; 493 ± 5% 3550 ±2% Remarks • Case temperature limited to TC=125°C max. • Product reliability results are valid for Tj=150°C • Dynamic values apply to the following combination of resistors: RGon,main = 0,5  RGoff,main = 0,5  RG,X = 2,2  RE,X = 0,5  GD 2 Rev. 2 – 16.02.2011 © by SEMIKRON SEMiX453GD12Vc Fig. 1: Typ. output characteristic, inclusive RCC'+ EE' Fig. 2: Rated current vs. temperature IC = f (TC) Fig. 3: Typ. turn-on /-off energy = f (IC) Fig. 4: Typ. turn-on /-off energy = f (RG) Fig. 5: Typ. transfer characteristic Fig. 6: Typ. gate charge characteristic © by SEMIKRON Rev. 2 – 16.02.2011 3 SEMiX453GD12Vc Fig. 7: Typ. switching times vs. IC Fig. 8: Typ. switching times vs. gate resistor RG Fig. 9: Typ. transient thermal impedance Fig. 10: Typ. CAL diode forward charact., incl. RCC'+EE' Fig. 11: Typ. CAL diode peak reverse recovery current Fig. 12: Typ. CAL diode recovery charge 4 Rev. 2 – 16.02.2011 © by SEMIKRON SEMiX453GD12Vc SEMiX 33c pinout This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, Chapter IX * The specifications of our components may not be considered as an assurance of component characteristics. Components have to be tested for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our staff. © by SEMIKRON Rev. 2 – 16.02.2011 5