ECLAMP0501T.TCT

Low Profile EClamp® 1-Line ESD protection PROTECTION PROTECTION PRODUCTS - EMIClamp® Description The EClamp 0501T TVS diode is designed to protect sensitive electronics from damage or latch-up due to ESD. This state-of-the-art device utilizes solid-state silicon-avalanche technology for superior clamping performance and DC electrical characteristics. It has been optimized for protection of digital lines in cellular phones and other portable electronics. ® EClamp0501T Features Transient protection for data lines to IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (tp = 5/50ns) Cable Discharge Event (CDE) Ultra-small package (1.0 x 0.6 x 0.4mm) Protects one data line T VS working voltage: 5V Series Resistor: 1K Ohm Capacitance: 15pF (Maximum at VR = 0V) Low leakage current Solid-state silicon-avalanche technology The device replaces two discrete components in a small footprint. It consists of a TVS diode and a series 1K Ohm resistor. The TVS diode presents a maximum loading capacitance of 15pF for maximum signal integrity. The TVS diodes provide effective suppression of ESD voltages in excess of ±15kV (air discharge) and ±8kV (contact discharge) per IEC 61000-4-2, level 4. The EClamp0501T is in a 3-pin, SLP1006P3T package. It measures 1.0 x 0.6 mm with a nominal height of only 0.4mm. The leads are spaced at a pitch of 0.65mm and are finished with lead-free NiPdAu. Each device will protect one line operating at 5 volts. It gives the designer the flexibility to protect single lines in applications where arrays are not practical. The small package makes it ideal for use in portable electronics such as cell phones, digital still cameras, and PDAs. Mechanical Characteristics SLP1006P3T package Pb-Free, Halogen Free, RoHS/WEEE Compliant Nominal Dimensions: 1.0 x 0.6 x 0.4 mm Lead Finish: NiPdAu Molding compound flammability rating: UL 94V-0 Marking : Marking code, cathode band Packaging : Tape and Reel Applications Cellular Handsets & Accessories Personal Digital Assistants (PDAs) Notebooks & Handhelds Portable Instrumentation Peripherals MP3 Players Schematic Package Configuration 1.0 1K Ω 1 15pF 2 0.60 0.65 3 0.40 3 Pin SLP package (Bottom Side View) Nominal Dimensions in mm 1 www.semtech.com Pin Identification and Configuration (Top Side View) Revision 04/14/2010 EClamp0501T PROTECTION PRODUCTS Absolute Maximum Rating R ating Peak Pulse Power (tp = 8/20μs) Maximum Peak Pulse Current (tp = 8/20μs) ESD p er IEC 61000-4-2 (Air) 1 ESD p er IEC 61000-4-2 (Contact) Op erating Temp erature Storage Temp erature 1 Symbol Pp k Ip p VESD TJ TSTG Value 25 2 +/- 17 +/- 12 -40 to +85 -55 to +150 Units Watts Amps kV °C °C Notes: 1) ESD rating between pin 1 and ground. Pin 2 not rated for IEC level ESD discharges Electrical Characteristics (T=25oC) P ar am et er T VS Reverse Stand-Off Voltage T VS Reverse Breakdown Voltage T VS Reverse Leakage Current Total Series Resistance Total Cap acitance S y m b ol VRWM V BR IR R Cin It = 1mA VRWM = 5.0V Each Line Inp ut to Gnd, Each Line VR = 0V, f = 1MHz 850 10 1000 12 6 8 Con d i t i on s Mi n i mu m Ty p i c a l M ax i m u m 5 10 0.5 1150 15 Units V V μA Ohms pF Pin Identification and Configuration Pin 1 2 3 Symbol I/O In I/O Out GN D Identification Data Inp ut (Connector Side) Data Outp ut (To Protected IC) Ground 2 1 3 Pin Configuration (Top View) © 2010 Semtech Corp. 2 www.semtech.com EClamp0501T PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time 10 Power Derating Curve 110 100 90 % of Rated Power or IPP 80 70 60 50 40 30 20 10 0 Peak Pulse Power - PPP (kW) 1 0.1 0.01 0.1 1 10 100 Pulse Duration - tp (us) 0 25 50 75 100 o 125 150 Ambient Temperature - TA ( C) Normalized Junction Capacitance vs. Reverse Voltage 1.1 1 0.9 0.8 CJ(VR) / CJ(VR=0) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 Reverse Voltage - VR (V) 4 5 f = 1 MHz Forward Voltage vs. Forward Current 8 7 Forward Voltage - VF V) 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Forward Current - IF (A) Waveform Parameters: tr = 8μs td = 20μs ESD Clamping (Measured between Pin2 and Gnd) (8kV Contact per IEC 61000-4-2) CH1 S21 Insertion Loss S21 LOG 6 dB / REF 0 dB 1: -23.787 dB 300.797 MHz 0 dB -6 dB -12 dB -18 dB -24 dB 1 4 5 2: -30.249 dB 800.000 MHz 3: -30.785 dB 900.000 MHz 4: -26.674 dB 1.8 GHz 5: -21.176 dB 2.5 GHz -30 dB 2 3 -36 dB 1 MHz 10 MHz 100 MHz 3 1 GHz GHz . STOP 3000 000000 MHz Note: Data is taken with a 10x attenuator © 2010 Semtech Corp. 3 START. 030 MHz www.semtech.com EClamp0501T PROTECTION PRODUCTS Applications Information Device Connection Options This device is designed to protect one data line. The device is unidirectional and may be used on lines where the signal polarity is above ground. The cathode band should be placed towards the line that is to be protected. Circuit Board Layout Recommendations for Suppression of ESD. Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are recommended: Place the TVS near the input terminals or connectors to restrict transient coupling. Minimize the path length between the TVS and the protected line. Minimize all conductive loops including power and ground loops. The ESD transient return path to ground should be kept as short as possible. Never run critical signals near board edges. Use ground planes whenever possible. Circuit Diagram 1K Ω 1 15pF 2 3 © 2010 Semtech Corp. 4 www.semtech.com EClamp0501T PROTECTION PRODUCTS Applications Information - Spice Model R1 1 D1 1K Ω 2 3 EClamp0501T Spice Model Table 1 - EClamp0501T Spice Parameters Parameter IS BV VJ RS IB V CJO TT M N EG Unit Amp Volt Volt Ohm Amp Farad sec --eV D1 (T VS) 2E-15 7.56 0.776 0.912 1.0E-3 11.5E-12 2.541E-9 0.23 1.1 1.11 © 2010 Semtech Corp. 5 www.semtech.com EClamp0501T PROTECTION PRODUCTS Outline Drawing - SLP1006P3T A D B DIM E A aaa C A1 L2 C L b2 C L e L1 0.40 C SEATING PLANE A A1 b1 b2 D E e L1 L2 N aaa bbb DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .015 .016 .017 0.37 0.40 0.43 .000 .001 .002 0.00 0.03 0.05 .004 .006 .008 0.10 0.15 0.20 .018 .020 .022 0.45 0.50 0.55 .035 .039 .043 0.90 1.00 1.10 .020 .024 .028 0.50 0.60 0.70 .014 BSC 0.35 BSC .008 .010 .012 0.20 0.25 0.30 .008 .010 .012 0.20 0.25 0.30 3 3 .003 0.08 .004 0.10 b1xN bbb CAB NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). Land Pattern - SLP1006P3T P P/2 X1 DIMENSIONS Y (C) G Z Y DIM C G P X1 X2 Y Z INCHES (.028) .016 .014 .008 .022 .012 .039 MILLIMETERS (0.70) 0.40 0.35 0.20 0.55 0.30 1.00 X2 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. © 2010 Semtech Corp. 6 www.semtech.com EClamp0501T PROTECTION PRODUCTS Marking Code Ordering Information Part Number EClamp 0501T.TCT Working Voltage 5V Qty per Reel 3,000 Reel Size 7 Inch 6T Tape and Reel Specification Notes: 1) This is a lead-free, RoHS/WEEE compliant product EMIClamp and EClamp are marks of Semtech Corporation Pin 1 Location User Direction of feed Device Orientation in Tape A0 0.69 +/-0.10 mm B0 1.19 +/-0.10 mm K0 0.66 +/-0.10 mm Tape Width B, (Max) D 1.5 + 0.1 mm - 0.0 mm (0.59 +.005 - .000) D1 E 1.750±.10 mm (.069±.004) F P 4.0±0.10 mm (.157±.004) P0 4.0±0.1 mm (.157±.004) P2 T W 8.0 mm + 0.3 mm - 0.1 mm (.312±.012) 8 mm 4.2 mm (.165) 0.4 mm ±0.25 (.031) 3.5±0.05 mm (.138±.002) 2.0±0.05 mm (.079±.002) 0.254±0.02 mm (.016) Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 www.semtech.com © 2010 Semtech Corp. 7