ECLAMP2455K.TCT

ESD/EMI Protection for SIM Card PROTECTION PROTECTION PRODUCTS - EMIClampTM Description The EClampTM2455K is combination EMI filter and line termination device with integrated TVS diodes for use on SIM Card interfaces on cellular phones and other portable electronics. This state-of-the-art device utilizes solid-state silicon-avalanche technology for superior clamping performance and DC electrical characteristics. The device consists of three circuits that include series impedance matching resistors for proper termination of the SIM card interface. Termination resistor value of 100 Ohms is included on the RST and Data lines and 47 Ohms on the CLK line. TVS diodes are also included on each line for ESD protection in excess of ±15kV (air discharge) and ±8kV (contact discharge) per IEC 610004-2, level 4. An additional TVS diode connection is included for protection of the voltage (Vcc) bus. The EClamp2455K is in a 8-pin, RoHS/WEEE compliant, SLP1713P8 package. It measures 1.7 x 1.3 x 0.50mm. The leads are spaced at a pitch of 0.4mm and are finished with lead-free NiPdAu. The small package makes it ideal for use in portable electronics such as cell phones and digital still cameras. EClamp2455K PRELIMINARY Features Bidirectional EMI/RFI filter with integrated TVS for ESD protection ESD protection to IEC 61000-4-2 (ESD) Level 4, ±15kV (air), ±8kV (contact) T VS working voltage: 5V Termination Resistors: 100 Ohms & 47 Ohms Capacitance: 20pF (Typical at VR = 0V) Protection and filtering for four lines Solid-state technology Mechanical Characteristics SLP1713P8 8-pin package RoHS/WEEE Compliant Nominal Dimensions: 1.7 x 1.3 x 0.50 mm Lead Pitch: 0.4mm Lead finish: NiPdAu Marking: Marking Code Packaging: Tape and Reel per EIA 481 Applications SIM Card Cell Phone PDAs and Smartphones Pin Configuration Package Configuration 1.70 12 RST Out CLK Out 1 8 RST In CLK In Data In 1.30 Gnd Data Out NC 4 5 0.40 BSC Vcc 0.50 Pin Identification and Configuration (Top Side View) Revision 03/27/2007 1 8 Pin SLP package (Bottom Side View) Nominal Dimensions in mm www.semtech.com EClamp2455K PROTECTION PRODUCTS Pin Identification and Configuration PRELIMINARY Pin 1, 8 2, 7 3, 6 4 5 Center tab Symbol RST C LK Data NC Vcc GND Identification Reset input/output with termination resistor Clock input/output with termination resistor Data input/output with termination resistor No Connect Power Supply ESD Protection Ground connection 8 7 6 5 Gnd 1 2 3 4 Pin Configuration (Top View) Schematics & Component Values Vcc 100 Ω RST IN 47 Ω RST OUT CLK OUT 100 Ω CLK IN Data IN Data OUT GND © 2007 Semtech Corp. 2 www.semtech.com EClamp2455K PROTECTION PRODUCTS Maximum Ratings R ating ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) Junction Temp erature Op erating Temp erature Storage Temp erature Symbol VESD TJ Top TSTG Value +/- 18 +/- 12 125 -40 to +85 -55 to +150 PRELIMINARY Units kV o C C C o o Electrical Characteristics (T=25oC) P ar am et er T VS Reverse Stand-Off Voltage T VS Reverse Breakdown Voltage T VS Reverse Leakage Current Reset Series Resistors Clk Series Resistors Data Series Resistors Total Cap acitance S y m b ol VRWM V BR IR RRST R CLK Con d i t i on s Mi n i mu m Ty p i c a l M ax i m u m 5 Units V V μA Ohms Ohms Ohms pF It = 1mA VRWM = 5.0V Each Line Each Line Each Line Inp ut to Gnd, Each Line VR = 0V, f = 1MHz 6 8 10 0.5 85 40 85 16 100 47 100 20 115 55 115 24 RDATA Cin © 2007 Semtech Corp. 3 www.semtech.com EClamp2455K PROTECTION PRODUCTS Typical Characteristics Typical Insertion Loss S21 (Pin 2 to 7) CH1 S21 LOG 6 dB / REF 0 dB 1: -6.4316 dB 307.466 MHz 2: -14.641 dB 900 MHz 3: -23.808dB 1.8 GHz 4: -28.845 dB 2.5 GHz 5: -30.455 dB 2.7 GHz 3 5 5 3 4 4 PRELIMINARY Typical Insertion Loss S21 (Pin 1 to 8 and Pin 3 to 6) CH1 S21 LOG 6 dB / REF 0 dB 1: -8.9909 dB 294.402 MHz 2: -19.003 dB 900 MHz 3: -28.966dB 1.8 GHz 1 0 dB -6 dB 1 0 dB -6 dB -12 dB -18 dB 2 -12 dB -18 dB -24 dB -30 dB -36 dB -42 dB -48 dB 1 MHz START. 030 MHz 10 MHz 100 MHz 2 4: -30.765 dB 2.5 GHz 5: -30.974 dB 2.7 GHz -24 dB -30 dB -36 dB -42 dB 1 3 GHz GHz . STOP 3000 000000 MHz -48 dB 1 MHz START. 030 MHz 10 MHz 100 MHz 1 3 GHz GHz . STOP 3000 000000 MHz ESD Clamping (+8kV Contact) ESD Clamping (-8kV Contact) Note: Data is taken with a 10x attenuator Note: Data is taken with a 10x attenuator Normalized Capacitance vs. Reverse Voltage 1.1 1 0.9 0.8 Analog Crosstalk (Each Line) C H1 S21 LOG 20 dB / EF 0 dB R CJ(VR) / CJ(VR=0) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 f = 1 MHz 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 START. 030 M Hz STOP 3000. 000000 M Hz Reverse Voltage - VR (V) © 2007 Semtech Corp. 4 www.semtech.com EClamp2455K PROTECTION PRODUCTS Device Connection The EClamp2455K designed with ease of layout in mind. The package has flow through design which allows the designer to route the signals straight in and out between the SIM port connector and the SIM controller. The device is in a 8-pin SLP package. Electrical connection is made to the 8 pins located at the bottom of the device. A center tab serves as the ground connection. Pin connections are noted in Figure 1. All path lengths should be kept as short as possible to minimize the effects of parasitic inductance in the board traces. PRELIMINARY Figure 1 - Pin Identification and Configuration (Top Side View) RST Out CLK Out 1 8 RST In CLK In Data In Gnd Data Out NC 4 5 Vcc SIM Card Connector SIM Controller RST OUT CLK OUT DATA OUT 4 Gnd 1 8 RST In CLK IN DATA IN Reset Clock Data I/O 5V/3.3V/1.8V 5 Vcc EClamp2455K EClamp2455P Figure 2 - SIM Protection © 2007 Semtech Corp. 5 www.semtech.com EClamp2455K PROTECTION PRODUCTS Applications Information - Spice Model EClamp2455K Spice Model & Parameters Vcc PRELIMINARY 100 Ω RST IN 47 Ω RST OUT CLK OUT 100 Ω CLK IN Data IN Data OUT GND EClamp2455K Spice Model Note: All TVS shown in the circuit use D1 Parameters Table 1 - EClamp2455K Spice Parameters Parameter IS BV VJ RS IB V CJO TT M N EG Unit Amp Volt Volt Ohm A mp Farad sec --eV D1 (T VS) 2E-15 7.5 0.775 1.05 1E-3 9E-12 2.541E-9 0.246 1.1 1.11 © 2007 Semtech Corp. 6 www.semtech.com EClamp2455K PROTECTION PRODUCTS Outline Drawing - SLP1713P8 PRELIMINARY A D B DIM PIN 1 INDICATOR (LASER MARK) E DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .018 .020 .022 .000 .001 .002 (.005) .006 .008 .010 .065 .067 .070 .047 .051 .055 .049 .051 .054 .008 .012 .016 .016 BSC .008 .010 .012 8 .003 .004 0.45 0.50 0.55 0.00 0.02 0.05 (0.13) 0.15 0.20 0.25 1.65 1.70 1.775 1.20 1.30 1.40 1.25 1.30 1.375 0.20 0.30 0.40 0.40 BSC 0.20 0.25 0.30 8 0.08 0.10 A aaa C A2 A1 C SEATING PLANE A A1 A2 b D D1 E E1 e L N aaa bbb D1 1 E1 N e/2 e D/2 2 LxN E/2 bxN bbb CAB NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. Land Pattern - SLP1713P8 P X DIM C G H K P X Y Z DIMENSIONS INCHES MILLIMETERS (.050) (1.27) .027 0.69 .012 0.30 .055 1.40 .016 0.40 .008 0.20 .023 0.58 .073 1.85 Z G Y K H (C) NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. © 2007 Semtech Corp. 7 www.semtech.com EClamp2455K PROTECTION PRODUCTS Marking PRELIMINARY Ordering Information Part Number Qty per Reel 3000 R eel Size 7 Inch PIN 1 INDICATOR 2455K XXXX EClamp 2455K.TCT This is a lead-free RoHS/WEEE Compliant Device EMIClamp and EClamp are marks of Semtech Corporation XXXX = Date Code Tape and Reel Specification Pin 1 Location User Direction of feed Device Orientation in Tape A0 1.51 +/-0.05 mm B0 1.91 +/-0.05 mm K0 0.66 +/-0.05 mm Tape Width B, (Max) D 1.5 + 0.1 mm - 0.0 mm (0.59 +.005 - .000) D1 E 1.750±.10 mm (.069±.004) F K (MAX) P 4.0±0.1 mm (.157±.004) P0 4.0±0.1 mm (.157±.004) P2 T(MAX) W 8.0 mm + 0.3 mm - 0.1 mm (.312±.012) 8 mm 4.2 mm (.165) 0.8 mm ±0.05 (.031) 3.5±0.05 mm (.138±.002) 2.4 mm (.094) 2.0±0.05mm (.079±.002) 0.4 mm (.016) Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 © 2007 Semtech Corp. 8 www.semtech.com