SC618_08

SC618 Charge Pump Flash LED Driver with Safety Timer POWER MANAGEMENT Features Flash and spotlight — two selectable modes Flash mode — up to 700mA output Flash mode — 500mA max output (over rated voltage, temperature, and load conditions) Flash mode safety timer shut-off — 1 second Spotlight mode set to 40% of flash current Spotlight mode — up to 280mA output Spotlight mode —1x mode (under most conditions) for best efficiency Input range — 3.0V to 5.25V External flash control pin for synchronization to a camera module or graphics controller Short-circuit, over-voltage, and over-temperature protection Soft-start functionality Separate flash and spotlight control inputs for maximum versatility Ultra-thin package MLPD-UT-10 — 3mm x 3mm x 0.6mm Description The SC618 is a high-current charge pump designed specifically for use with white LEDs used in camera flash applications. Only two small bucket capacitors are required to develop the output drive, providing a low EMI solution compared to inductive boost regulators. The SC618 has two modes of operation: flash mode and spotlight mode. In flash mode, the SC618 is capable of delivering 500mA of regulated current for a duration of 500ms or up to 700mA for a reduced duration. A safety timer is also included to ensure the LED cannot be left on indefinitely and overheat. In spotlight mode the SC618 outputs 40% of the flash mode current and can remain enabled continuously. An external resistor is connected in series with the LED to set the current. In flash mode, this resistor can dissipate up to 175mW, reducing the power dissipation requirement of the SC618. The flash input overrides the control input to make sure the flash function is activated . The SC618 ultra-thin package provides both a low profile and high thermal efficiency. Applications Mobile camera phones Digital cameras PDAs with built-in cameras Typical Application Circuit SC618 VIN VBAT VOUT GND ISET CTRL FLASH 10μF C1+ 1μF White LED 1μF C1C2+ 1μF C2- RSET FLASH CTRL February 6, 2008 1 SC618 Pin Configuration Ordering Information Device SC618ULTRT(1)(2) SC618EVB VIN C2GND C1FLASH 1 2 3 4 5 T Package MLPD-UT-10 3×3 Evaluation Board 10 TOP VIEW 9 8 7 6 C2+ VOUT C1+ CTRL ISET Notes: (1) Available in tape and reel only. A reel contains 3,000 devices. (2) Lead-free package only. Device is WEEE and RoHS compliant. MLPD-UT-10; 3x3, 10 LEAD θJA = 40°C/W Marking Information 618 yyww xxxx yyww = Date code xxxx = Semtech Lot Number 2 SC618 Absolute Maximum Ratings VIN (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.5 VOUT (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.5 C1+, C2+ (V) . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VOUT + 0.3) Pin Voltage - All Other Pins (V) . . . . . . -0.3 to (VIN + 0.3) Circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous ESD Protection Level(1) (kV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Thermal Resistance, Junction to Ambient(2) (°C/W) . . . . 40 Junction Temperature Range (°C) . . . . . . . . . . . . -40 to +150 Storage Temperature Range (°C) . . . . . . . . . . . . . -60 to +150 Peak IR Reflow Temperature (10s to 30s) (°C) . . . . . . . +260 Recommended Operating Conditions Ambient Temperature Range (°C) . . . . . . . . . . . . -40 to +85 Thermal Information Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not recommended. NOTES: (1) Tested according to JEDEC standard JESD22-A114-B. (2) Calculated from package in still air, mounted to 3” x 4.5”, 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. Electrical Characteristics Unless otherwise specified: TA = 25°C for TYP, -40°C to +60°C for MIN and MAX; CBUCKET = COUT = 1.0μF (ESR < 0.1Ω); CIN = 10.0μF; VIN = 3.0V to 5.25V; VOUT = 2.8V to 4.25V; RSET = 0.5Ω (0.1%). Parameter Symbol Conditions FLASH high, RSET = 0.357Ω 3.7V < VIN < 4.2V, VOUT = 3.7V(1) FLASH high, RSET = 0.5Ω 3.3V < VIN < 4.2V 2.8V < VOUT < 4.25V FLASH low, CTRL high, RSET = 0.357Ω 3.7V < VIN < 4.2V, VOUT = 3.4V(1) FLASH low, CTRL high, RSET = 0.5Ω 3.0V < VIN < 4.5V 2.8V < VOUT < 4.5V FLASH high, RSET = 0.5Ω 3.3V < VIN < 4.2V 2.8V < VOUT < 4.25V FLASH low, CTRL high, RSET = 0.5Ω 3.0V < VIN < 4.5V 2.8V < VOUT < 4.5V FLASH high Min Typ 700 Max Units 460 500 540 mA Output Current IOUT 280 170 200 230 230 250 270 mV ISET Reference Voltage VISET 85 100 115 3.4 2.0 0.1 5.0 4.5 2.0 mA mA μA Quiescent Current IQ FLASH low, CTRL high FLASH low, CTRL low 3 SC618 Electrical Characteristics (continued) Parameter Flash Mode Pulse Duration(2) Flash Mode Start-Up Time(2) Flash Mode Safety Timer(2) Spotlight Mode Start-Up Time(2,3) Oscillator Frequency Oscillator Frequency Accuracy Short-Circuit Output Current Limit Symbol tFLASH tF-SU tSAFE tS-SU fOSC ΔfOSC ISC Conditions 3.3V < VIN < 4.2V IOUT = 500mA, VOUT > 2.8V t = 0 when FLASH goes high to IOUT = 90% of final value FLASH high VIN = 4.2V, VOUT = 3.2V; t = 0 when CTRL goes high to IOUT = 90% of final value Device enabled Min Typ Max 500 1 Units ms ms s ms kHz 0.90 1.25 1 250 -15 Steady State with VOUT shorted to GND 2x mode, 3.3V < VIN < 4.2V 15 600 2.1 % mA Input Current Limit ILIMIT 2x mode, VIN = 3.7V, VOUT = 3.7V, TA = 25°C TOT Rising threshold Hysteresis FLASH, CTRL FLASH, CTRL FLASH 1 2 20 40 0.1 25 A 1.38 150 °C 10 1.5 0.4 35 μA CTRL 70 2.0 μA V V 1.53 Over-Temperature Protection(2) TOT -HYS Logic Input High Threshold Logic Input Low Threshold VIH VIL Logic Input High Current IIH Logic Input Low Current IIL FLASH, CTRL Spotlight mode — IOUT = 200mA ISET Ripple Voltage VISET(P-P) FLASH mode — IOUT = 500mA 100 mV Notes: 1) VOUT required by the typical LED at this current. 2) Guaranteed by design - not tested in production. 3) If conditions force 2x mode operation, this start-up time will increase by approximately 32ms due to the timer that is enabled to ensure 2x mode is needed. 4 SC618 Typical Characteristics Flash Current at 10ms, RISET = 500mΩ, VOUT = 3.75V 515 Flash Current at 100ms, RISET = 500mΩ, VOUT = 3.68V 515 510 510 LED Current (mA) 500 LED Current (mA) 505 505 500 495 495 490 490 485 3.3 3.45 3.6 3.75 VIN (V) 3.9 4.05 4.2 485 3.3 3.45 3.6 3.75 VIN (V) 3.9 4.05 4.2 Flash Current at 500ms, RISET = 500mΩ, VOUT = 3.58V 515 Spotlight Current, RISET = 500mΩ, VOUT = 3.16V 220 510 212 LED Current (mA) LED Current (mA) 505 Transition to 2x Mode 1x Mode 204 500 196 495 490 485 3.3 188 3.45 3.6 3.75 VIN (V) 3.9 4.05 4.2 180 5.25 4.8 4.35 VIN (V) 3.9 3.45 3 Flash Duration, RISET = 350mΩ, VOUT = 3.86V (start), 3.61V (LED Heated 500ms) 755 Flash Duration, RISET = 500mΩ, VOUT = 3.75V (start), 3.58V (LED Heated 500ms) 515 735 LED Current (mA) 509 LED Current (mA) VIN=4.2V VIN=3.7V 715 VIN=3.7V 503 VIN=4.2V 497 VIN=3.3V 695 VIN=3.4V 491 VIN=3.3V 675 0 100 200 300 Pulse Duration (ms) 400 500 485 0 100 200 300 Pulse Duration (ms) 400 500 5 SC618 Typical Characteristics (continued) Flash Mode Ripple, RISET = 500mΩ Start-Up Flash Mode, 500mA Ch 1: 100mV/DIV Ch 2: 200mV/DIV Ch 3: 200mV/DIV Time (4μs/div) Time (40μs/div) Ch 1: 100mV/DIV Ch 2: 2V/DIV Ch 3: 2V/DIV Safety Timer Shut-Off Spotlight 1x Mode Ripple, RISET = 500mΩ Ch1: 100mV/DIV Ch2: 2V/DIV Ch3: 5V/DIV Time (200ms/div) Time (4μs/div) Ch1: 50mV/DIV Ch2: 50mV/DIV Ch3: 50mV/DIV Spotlight 2x Mode Ripple, RISET = 500mΩ Short Circuit Current Limiting, VIN = 5.25V, VOUT = 0V Ch1: 50 mV/DIV Ch2: 100 mV/DIV Ch3: 100 mV/DIV Time (4μs/div) Time (400ms/div) Ch1: 2V/DIV Ch4: 100mA/DIV 6 SC618 Pin Descriptions Pin# 1 2 3 4 5 6 7 8 9 10 T Pin Name VIN C2GND C1FLASH ISET CTRL C1+ VOUT C2+ Thermal Pad Pin Function Input voltage Negative terminal of bucket capacitor 2 Ground— connect to ground plane using multiple vias Negative terminal of bucket capacitor 1 Flash mode enable pin— puts the device in active flash mode when high and also overrides CTRL. Current-setting reference pin — connect to the LED cathode and the current setting resistor. Control input bit — used to enable and set the output current in spotlight mode when high. Positive terminal of bucket capacitor 1 Output pin — connect to the LED anode Positive terminal of bucket capacitor 2 Pad for heat sinking purposes — not connected internally. Connect to ground plane using multiple vias. 7 SC618 Block Diagram VIN 1 LDO 8 C1+ 250kHz 4 C1- 10 C2+ CTRL FLASH 7 5 Logic Control and Flash Mode Timer CHARGE PUMP 2 C2- Reference Voltage Generator 9 VOUT 3 GND 6 ISET 8 SC618 Applications Information General Operation The SC618 is a powerful dual-mode charge pump designed to drive a high-intensity white LED. A constant current spotlight mode or a pulsed current with higher intensity is used for camera flash. The device operates in 2x mode while operating in flash mode. In spotlight mode it can operate in either 2x or 1x mode depending on the load current, load voltage, and input voltage levels. In flash mode the SC618 output can drive 500mA at 4.25V into an LED for a minimum duration of 500ms under all temperature and input conditions. The FLASH pin is used to trigger this mode (active high). In spotlight mode the SC618 regulates the output current to 40% of the flash mode current setting, when the CTRL pin is pulled high and the FLASH pin is low. Flash mode has priority over spotlight mode, i.e., the FLASH pin triggers flash mode regardless of the state of the CTRL pin. Output current is regulated by attaching the ISET pin to the cathode(s) of the LED package and a low resistance sense resistor (typically 0.5Ω). The ISET pin monitors the voltage at the cathode and signals the charge pump to increase or decrease the output current until the ISET voltage reaches the programmed setting. The resistor value is chosen to set the current through the LED based on this reference voltage. The resistor can be chosen to set either the flash mode current or spotlight mode current, but it should not be less than 0.35Ω due to output current limitations of the device. example, 700mA derates to a maximum of 350ms. In flash mode, IOUT = 250mV/RISET. Figure 1 shows maximum flash mode current for extended duration times. 800 700 Flash Current [mA] 600 500 400 300 200 100 0 0 100 200 300 400 500 600 700 800 900 1000 Flash Duration [ms] Figure 1 — Maximum Flash Duration Flash Mode Safety Timer The SC618 provides a time-out protection function when in flash mode. The output is disabled if the FLASH pin is held high for longer than 1 second to protect the LED. Once this time-out has occurred, the output will stay disabled until the FLASH pin has been pulled low and then re-enabled. Spotlight Mode Spotlight mode is enabled by setting the CTRL pin high and keeping the FLASH pin low. When in spotlight mode, the SC618 can maintain a constant current indefinitely to drive an LED or bank of LEDs. The ISET reference voltage is set to 100mV so that the output current is maintained at 200mA when a 0.5Ω resistor is used. Spotlight current is always 40% of flash current for any given value of RISET. In spotlight mode, IOUT = 100mV/RISET. To maximize power efficiency, the SC618 has been designed to operate in 1x mode when conditions do not require the charge pump to be active. When first enabled the SC618 attempts to regulate the voltage on the ISET pin in 1x mode. If the voltage on the ISET pin cannot be maintained and this condition persists for longer than 32ms, then the charge pump will change to 2x mode operation. In a typical application, the SC618 will operate in 1x mode until the supply voltage decreases sufficiently 9 Flash Mode Flash mode is enabled whenever the FLASH pin is pulled high and remains active until the FLASH pin is released. This mode has higher priority than spotlight mode, so the state of the CTRL pin is overridden whenever the FLASH pin is activated. While in flash mode the reference voltage on the ISET pin is set to 250mV. The duration of the pulse is limited by the amount of power that can be dissipated in the SC618 before it exceeds the maximum operating temperature. If an output current less than the rated 500mA is desired, the duration of the pulse can increase proportionally. Extending flash mode beyond the 500ms pulse limit could adversely affect the long term reliability of the SC618. Flash duration must be derated at higher currents. For SC618 Applications Information (continued) that the voltage on the ISET pin can no longer be maintained. After a 32ms delay (included to prevent false transitions) the charge pump will convert to 2x mode. After the charge pump switches from 1x mode to 2x mode, the device remains in 2x mode until the part is turned off. If the part is re-enabled in spotlight mode, it will begin operation in 1x mode and determine the appropriate mode of operation as previously described. Over-Current Protection When the SC618 is in 2x mode, the input current will be approximately double the required output. When the steady-state load requires the maximum current available in 2x mode, the OCP circuit prevents the device from overheating from excessive power dissipation. This feature protects the device when in 1x mode. The current limit is set lower in the 1x mode due to lower current requirements. Short-Circuit Current Protection SSCP is provided to limit the current that can be sourced when the output is shorted to ground. When a short circuit forces VOUT to drop below 2V, the SCCP detects the condition and limits the output current. Protection Circuitry The SC618 provides several protection features to safeguard the device from catastrophic failures. These features include: • • • • • Input Over-Voltage Protection (IOVP) Output Over-Voltage Protection (OVP) Over-Temperature Protection (OTP) Over-Current Protection (OCP) Short-Circuit Current Protection (SCCP) Resistor Selection The ISET resistor selection is critical in generating the correct current. The value can be chosen to set the spotlight mode current or the flash mode current, and the two current settings are dependent on the same resistor. It is recommended that the resistor be selected to match the desired LED current for flash mode. This allows the designer to set the SC618’s maximum current and select the resistor package size necessary for the power dissipation required in flash mode. The typical application uses a 0.5Ω resistor to set a flash mode current of 500mA and spotlight mode current of 200mA. A high precision resistor should be used to ensure the specified accuracy for LED current. To avoid malfunction of the charge pump, it is recommended that the resistance seen at the ISET pin remain constant while the device is active (flash or spotlight mode). Changing the resistance value or the load current while the device is active could cause instability. Input Over-Voltage Protection IOVP is included to prevent operation at high input voltages that could damage the device. The IOVP circuit senses the input voltage and determines when the supply exceeds 6V. Hysteresis is included in this circuit to avoid chattering between states. When the voltage rises above this threshold, the device is disabled until the input voltage drops to a level within the specified range. Output Over-Voltage Protection Output OVP prevents the SC618 from generating an output voltage that could damage other devices connected to it such as load LEDs and bypass capacitors. When the output voltage exceeds 5.5V, the OVP circuit disables the charge pump until the voltage decreases to a level within the acceptable range. This circuit allows the device to drive LEDs with high forward voltages at a reduced level without exceeding the output voltage limits specified for the device. Over-Temperature Protection The OTP circuit prevents the device from overheating and experiencing a catastrophic failure. When the junction temperature exceeds 150°C the device is disabled. It remains disabled until the junction temperature drops below this threshold. Hysteresis is included to prevent toggling between modes. Capacitor Selection The SC618 is designed to use low-ESR ceramic capacitors for the input and output bypass capacitors as well as the charge pump bucket capacitors. Ideal performance is achieved when C1 is exactly equal to C2. It is recommended that X5R or X7R ceramic capacitors be used for best performance. 10 SC618 Applications Information (continued) PCB Layout Considerations The following layout is suggested for a two-layer design. The capacitors C1 and C2 are the bucket capacitors and each conducts the full load current of up to 500mA pulsed for one half clock cycle. C3 is the output decoupling capacitor placed near the VOUT pin. C4 is the input decoupling capacitor placed near the VIN pin. Multiple vias should be used whenever it is necessary to change layers on nets connecting to pins VIN, VOUT, GND, C1-, C1+, C2- and C2+. The load current return path is from the ISET sense point through the resistor and back to the ground pins. Resistance in this path adds to the total resistance and has the effect of reducing the LED current by about 4% per 10mV of DC drop across the return copper trace in flash mode. For this reason, it is crucial to have a low resistance return path. Place and ground the resistor as close as possible to the ground pin of the SC618. The trace from the ISET pin has virtually no current. The ISET trace should make contact at the pad of the power sense resistor to minimize the effect of voltage drop between the LED cathode and the resistor. Resistor R1 is routed with a very low resistance connection between R1 and GND pin 3. The sense trace between Pin 6 and R1 is routed around the ground vias, allowing the shortest ground return path possible. The sense trace is connected to R1 at the positive terminal pad for the most accurate output possible. The bottom copper layer is mostly a ground plane with no obstructions between the ground vias. The smaller rectangle to the left connects the input power to VIN pin 1 and input capacitor C4. The two traces at the lower left are for logic inputs FLASH and CTRL. The trace to the right is the ISET pin sense trace. The sense trace is routed out of the path of the returning ground current. while in flash or spotlight mode. It is critical to maintain adequate ground plane around the device to maximize heat transfer and avoid over-temperature shutdown. Thermal Resistance Considerations The SC618 package is thermally efficient when the circuit board layout connects the thermal pad through multiple vias to the ground plane. The thermal resistance is rated at 40°C/W, and this rating is dependent on the connection between the thermal pad and the ground plane. The layout should keep the junction temperature below the OTP limit while operating the SC618 within the specified electrical conditions for IOUT and VISET. A poor layout may allow the junction temperature to reach the OTP limit 11 SC618 Outline Drawing — MLPD-UT-10 A E B DIM A A1 A2 E PIN 1 INDICATOR (LASER MARK) b C D E e L N aaa bbb A aaa C A1 C 1 LxN 2 A2 SEATING PLANE C .007 .074 .042 .114 .012 MIN .018 .000 DIMENSIONS INCHES NOM (.006) .009 .079 .048 .118 .020 BSC .016 10 .003 .004 .020 0.30 .011 .083 .052 .122 0.18 1.87 1.06 2.90 MAX .024 .002 MILLIMETERS MIN 0.45 0.00 NOM (0.1524) 0.23 2.02 1.21 3.00 0.50 BSC 0.40 10 0.08 0.10 0.50 0.30 2.12 1.31 3.10 MAX 0.60 0.05 D N e bxN bbb NOTES: 1. 2. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS. C A B 12 SC618 Land Pattern — MLPD-UT-10 K DIM C G (C) H G Z H K P Y X P X Y Z DIMENSIONS INCHES (.112) .075 .055 .087 .020 .012 .037 .150 MILLIMETERS (2.85) 1.90 1.40 2.20 0.50 0.30 0.95 3.80 NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 2. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. Contact Information Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 Fax: (805) 498-3804 www.semtech.com 13